Shenglong Injection packer for high pressure grout Features High pressure injection packers for concrete crack repairs , waterproofing ,rehabilitation of concrete structures , basement leak sealing cracksealing etc. Shenglong injection packer for injection machine spare parts is uesd with the Shenglong injection machine in concrete crack repair and water leaking stop. It suits for both polyurethane and epoxy injection. Method of Construction for Injection 1.Crack and leakage condition inspection Check the process procedure after finding the thickness, width and depth of crack and leakage condition of the structure 2.Drilling Operation Drill directly into crack section if the thickness of concrete is thinner than 10cm. For the thickness of 10~50cm, drill it with 45 degree angle by keeping a distance of 1/5 of concrete thickness. Make sure it penetrates the crack section. If the thickness is over than 50cm, keep the distance of 20~30cm and drill it with 45 degree angle until it penetrates crack section. And keep drilling by maintaining the fixed interval. (5 holes per 1 meter. Drill it in zigzags) 3.Packer Installation Clean the inside of drilled holes with compressor. Make sure that rubber sleeve of packer and cutting line of tightening nut should be put into the inside of concrete surface when installing. Tighten the packer completely by using the T-box. (Packer might be damaged if you tighten it too strongly) 4.Injection Operation Inject the waterstopping material by using the high pressure device or grease gun. Maintain the initial injection pressure as around 40kg/cm and increase the pressure by each 10kg/cm gradually until the waterstopping material flows out from crack section. Water will come out from the crack section first and then waterstopping foaming agent and then water stopping liquid at last. If the waterstopping material that is not foamed comes from the crack section, then move to next packer for injection. 5.Packer Removing Operation Remove and break the packer by using vise pliers or hammer as a tool. If there is still a wet section, then inject the water stopping material again. 6.Finishing Operation Remove the water stopping material that is remained on the crack section. Spreading with the elastic sealing material. SL-8 (80*13.5*14)mm SL-10 (100*13.5*14)mm SL-15 (150*13.5*14)mm SL-20 (200*13.5*14)mm SL-25 (250*13.5*14)mm SL-30 (300*13.5*14)mm SL-100 (1000*13.5*14)mm In carton
ModelHBTS50-13-92R Length(L)5000mm Width(W)1600mm Height(H)1800mm Hopper Capacity0.8m Feeding Height1280mm Weight4500kg Theoretical delivery pressure13Mpa Theoretical concrete output50m/h Hydraulic SystemOpen Diesel Engine BrandDauyz Weichai Power92kw Rotation speed2200r/min Distribution valveS Pipe Valve Hydraulic Cylinder Diameter100mm Concrete Cylinder Diameter180mm High/Low Pressure Switch Available Oil Tank Volume115L Hydraulic Oil Tank Volume460L Nude cargo in containers
ModelHBTS60-13-130R Length(L)7200mm Width(W)2100mm Height(H)2500mm Hopper Capacity0.8m Feeding Height1380mm Weight6200kg Theoretical delivery pressure13Mpa Theoretical concrete output60m/h Hydraulic SystemOpen Diesel Engine BrandDauyz Weichai Power130kw Rotation speed2200r/min Distribution valveS Pipe Valve Hydraulic Cylinder Diameter125mm Concrete Cylinder Diameter200mm High/Low Pressure Switch Available Oil Tank Volume230L Hydraulic Oil Tank Volume580L Nude cargo in containers
ModelHBTS80-16-161R Length(L)7200mm Width(W)2100mm Height(H)2500mm Hopper Capacity0.8m Feeding Height1380mm Weight6800kg Theoretical delivery pressure16Mpa Theoretical concrete output80m/h Hydraulic SystemOpen Diesel Engine BrandDeutz AG Power161kw Rotation speed2200r/min Distribution valveS Pipe Valve Hydraulic Cylinder Diameter140mm Concrete Cylinder Diameter200mm High/Low Pressure Switch Available Oil Tank Volume230L Hydraulic Oil Tank Volume580L Nude cargo in containers
ModelHBTS80-16-174R Length(L)7200mm Width(W)2100mm Height(H)2500mm Hopper Capacity0.8m Feeding Height1380mm Weight6780kg Theoretical delivery pressure16Mpa Theoretical concrete output80m/h Hydraulic SystemOpen Diesel Engine BrandVOLVO Power174kw Rotation speed2200r/min Distribution valveS Pipe Valve Hydraulic Cylinder Diameter140mm Concrete Cylinder Diameter200mm High/Low Pressure Switch Available Oil Tank Volume230L Hydraulic Oil Tank Volume580L Nude cargo in containers
ModelHBTS80-16-145R Length(L)7200mm Width(W)2100mm Height(H)2500mm Hopper Capacity0.8m Feeding Height1380mm Weight6500kg Theoretical delivery pressure16Mpa Theoretical concrete output80m/h Hydraulic SystemOpen Diesel Engine BrandDauyz Weichai Power145kw Rotation speed2200r/min Distribution valveS Pipe Valve Hydraulic Cylinder Diameter140mm Concrete Cylinder Diameter200mm High/Low Pressure Switch Available Oil Tank Volume230L Hydraulic Oil Tank Volume580L Nude cargo in containers
Precast Hollow Core Concrete Floor slab Forming Machine Precast concrete hollow core slab machine,The machine is mainly used to make the roofslab of house or building. The machine is making the beam through mechanical squeezing. It use the vibrator to compaction the slab make the cement, sand and stone etc. fastening together. We are having many types of the Beam Slabs Forming Machine, different model can produce different kinds of floor slab to make different building. Special type of concrete hollow core slab making machine. According to eaves slabs which from the house need to inclining in order to let rain sluicing quickly, and prevent rain leakage. SANKE researched and developed the inclined slab molding machinery. Users will be content with the labor and materials saving. Hollow Core Concrete slab Machine Motor Power(kw) Vibrator power(kw) Weight (kg) Forming speed(m/min) Holes no. Dia. Of holes Dimension L*W*H(m) TW50X500 3 0.8 700 1.2-1.4 8 25 1.8*0.75*0.65 TW50X500 +80X500 4.0 1.5 930 1.2-1.4 6 25 ( 42) 2.03*0.73*0.66 TW60X500 +80X500 4.0 1.5 910 1.2-1.4 7 ¦µ25 (¦µ42) 2.03*0.83*0.66 TW90X600 4.0 2.2 955 1.2-1.4 6 µ50 2.1*0.84*0.73 TW100X600 4.0 2.2 975 1.2-1.4 6 60 2.1*0.85*0.73 TW120X600 5.5 3.0 1050 1.2-1.4 5 76 2.1*0.85*0.75 TW120X900 7.5 3.0 1580 1.2-1.4 8 76 2.5*1.3*0.9 TW120X1200 7.5 3.0 1650 1.2-1.4 11 76 2.5*1.7*0.9 TW120x600 5.5 3.0 1150 1.2-1.4 5 76 2.3*1.1*0.9 TW180X600 7.5 3.0 1290 1.2-1.4 3 130 2.3*1.1*0.95 TW180X900 7.5 3.0 1900 1.2-1.4 5 130 2.8*1.5*1.4 HTY Hollow core slab machine Motor Power(kw) Motor Vibrator Power(kw) Inner vibrator power Forming speed (m/min) Holes no. Hole shape Weight(kg) 200x900 11 3.6 0.8 1-1.2 6 Peach 2600 250x900 11 4.7 0.8 1-1.2 6 Peach 3700 300x900 11 4.7 1.1 1-1.2 5 Peach 4500 200x1200 11 11 1.1 1-1.2 8 Peach 3100 250x1200 15 11 1.1 1-1.2 8 Peach 4500 300x1200 18.5 15 1.5 1-1.2 6 Peach 5100 Precast Concrete hollow core slab machine£¬concrete roof slab machine,Concrete block making machine,Concrete wall panel machine
Self travelling of 4 x 4 in job site, 60 cbm concrete pump, 140 hp euro4 diesel engine, 18 m hydraulic boom with radio remote control, Automatic lubrication, High pressure washing. 9.800 kg, Shipped in 40' high cube container
60 cbm/hr, 140 HP Euro4 diesel engine,automatic lubrication and high pressure washing; 4 weeks of training all included. 1.70 x 4.19 x 2.08 m ; 3.400 kg
Ultra light mobile placing boom; Detacheble boom unit from main frame, Radio remote control 2.100 kg, Shipped in 20' container
Failure phenomenon: batching station concrete trailer pump stone feed pneumatic door stones stuck not open. Analysis: batching station pneumatic door there is a big gap doors and small gap doors, big gap door its clearance greater than normal gravel particle size, so as to avoid the card material. Its small gap door gap is generally in the 5 ~ 10mm, 10mm below the stones card into the gap, it is difficult to pneumatic door jammed. Batching station after a period of use, the aggregate diesel engine concrete mixer spout wear, when the the gap wear to diesel concrete pump supplier 20 ~ 30mm, the card into the larger stones entering the gap in the process of the door, the gravel can easily stuck (wedge force) , pneumatic door can not be opened. Concrete mixing station troubleshooting method. twin shaft concrete mixer process: Check the pneumatic valve clearance and adjust to the appropriate value, can not be adjusted to the appropriate value as a result of excessive wear, you need to add welding steel plate or round bar in the feed opening, the gap reached a reasonable value. Take gray tank top, conveying powder to jar. Failure phenomenon: the bulk cement truck screw conveyer for sale the powder tank pump ashes, cement tank top with powder smoke. Analysis: conveying powder to powder cans transported by compressed air, compressed air, the powder to the powder cans into the air, such as dust removal machine cement mixing machine supplier filter clogging dust mobile concrete batching plant collector filter tank top, compressed air can not discharged generated "pressureout, and when the pressure reaches the safety valve opening pressure of the tank top, the safety valve opens, the diesel concrete pump for sale compressed air and powder through the safety valve is vented to the atmosphere, resulting in the risk ash phenomenon. Another level gauge failure, powder filled continue feeding also appears to take the gray tank top phenomenon. Process: 1, check movable concrete batching plants tank top dust filter and clean-up. 2, Once the take Ash phenomenon appears, you must clean up the safety valve around the powder, avoid powder caking the rain plug the safety valve. 3, as a result of the powder overfilled and take the gray, you must check on the level meter and a the material full alarm device reliability. Belt rainy slip. Fault slip phenomenon: a rainy day, inclined belt with load operation. Analysis: rainy, a moisture in the aggregate, and belt exposed parts easy to wet, damp, especially the inner ring and wet belt to screw conveyor reduce the coefficient of friction between the belt and the drive rollers, so that the drum is passed to the reduction in the belt torsional torch, the torque less than the belt material handling required torque, belt slipping.
Introduction of products 1.Super-strong steel structure , made of extensive imported original parts, ensuring more stability and reliability for the main machine body. 2.The whole process uses a plc aptitude control and dialogue system of human -machine interface, easy to analyze the chance signal , ensure the best operation effect. 3.High-efficiency and super-strong vibration system , computer control flow pressure of the hydraulic system , realise vertically thus greatly increase products compactness and mold-box service life. 4.The cloth system adopts semi-closed screen reticular feeding unit to feed materials forcedly , with evenness and even speed , ensuring product intensity. 5.Fitted with special hydraulic loading unit, readily realise mass and automatic production , saving a great deal of human power , maintenance , and circulating fund investment. The technical data of qt3-15 technology parameter are as follows: Outside size: 8000¡á1300¡á2700(mm) Weight: 8000kg Rated pressure: 21mp Vibration frequency: 50hz;3000-4000r/min Pallet size: 695¡á560¡á15(mm) Power: 30kw Material: slag, sand, flyash, cement Standard brick:(240¡á115¡á53)37500pcs/8hours Multi-hole brick:(240¡á115¡á90) 18750pcs/8hours Hollow brick:(390¡á190¡á190)6250pcs/8hours Standard seaworthy packing
High speed with reasonable price brick making machine in china we are a professional manufacturer in china, only focus on manufacturing block machine line. Our newest machine: qt6-15 feature: 900018002700(mm); daily output: standard brick(24011553)60000pcs, multi-hole brick(24011590)30000pcs, hollow brick(390190190)10000pcs. We provide leading technologies in block industry, from a standalone machine to a whole automated line, with world class flexibility, quality and cost-efficiency. We have already exported our machines to asia, us, and europe, india, many customers come back to order more lines. Technology parameter Outside size 900018002700(mm) Weight 11000kg Rated pressure 21mp Vibration frequency 50hz;3000-4000r/min Pallet size 110056020(mm) Power 45kw Daily output Standard brick (24011553)60000pcs Multi-hole brick(24011590)30000pcs Hollow brick (390190190)10000pcs Welcome to visit our factory when you are free, 2 hours by car from shanghai city, we will show how all the machines when they are working. Standard seaworthy packing
Detailed product description Construction mobile jdc500 concrete mixer 1.Safe and long service life 2.High quality, reliable performance 3.Iso9001:2000 Jdc500 concrete mixer High quality, reliable performance Safe and long service life Iso9001:2000 & sgs test 1. Feeding system : by the motor, hopper move on a track smooth and safety. 2. Discharge system : rotating cylinder discharge the materials in a short time. 3. Hydraulic system : reversing valve control, easy to operate. Main parameters and description of jdc500 single shaft concrete mixer Discharging volume: 500l Charging volume: 800l Max. Aggregate size: 80/60mm Mixing time :30s Working cycle times :70 batches per hour Capacity: 25~30m3/h Mixing blades rotating-speed :27.6r/min Bucket lifting speed: 19m/min Mixing motor model & power: y160l-4b5, 18.5kw Hoisting motor model & power: yej112m-4, 5.5kw Water pump model & power :50dw18-8a, 0.75kw Concrete discharging motor model & power: yej112m-4, 3kw Water feeding type :time relay Total weight: 4000kg Dimension :2820x2900x3260mm.
Product details: Place of origin: china (mainland) Brand name: nf Model number: js2000 Motor power :37.5kw Mixing power :37.5kw Charging capacity: 3200l Reclaiming capacity: 2000l Speed of mixing drum: 30 r/min Water supply mode: water pump Working cycle period :50s Discharge way ;hydraulic pressure Outline dimension :10560*3876*10710 Weight: 15600kg Condition: new Modle :js2000 Charging capacity (l) :3200 Discharging capacity (l) :2000 Production capacity(m3/h) :¡ý100 Max aggregate diameter(mm): 80/60 Cycle time (s): 50 Stirring motor power (kw) :37.5 Overall dimensions ( mm) :10560*3876*10710 Discharging height (m) :3.8 Total weight (kg): 15600 Detailed product description Js2000 concrete mixer Charging capacity (l):3200 Discharging capacity (l):2000 Cycle time (s):50 Discharging height (m):3.8 2012 new js2000 concrete mixer Specifications Js2000 concrete mixer for sale 1.Advanced electric control system 2. High quality and production 3. Easy to maintain 4. Excellent mixing performance 5. Ce & iso9000 6. Hot sell product Js2000 concrete mixer is applicable to the common construction working site, road, bridge and each kind of precast product factory. It can work independently or be used as facility concrete plant, which is applied with correspond batching machine. Js2000 concrete mixer has reposefully and low noise .The electrical system adopts import component, which is good performance and reliability.
Detailed product description Product details: Place of origin henan, china (mainland) Brand name nf Model number js1000 Motor power 2x37kw Mixing power 37kw Charging capacity 1600l Reclaiming capacity 1000l Speed of mixing drum 25.5r/min Water supply mode water pump Working cycle period 60s Discharge way automatic Outline dimension 8765x3436x9540mm Weight 8700kg Condition new Model js1000 Discharging volume 1000l Charging volume 1600l Max. Aggregate size 80/60mm Capacity 50m3/h Mixing blades rotating-speed& qty. 25.5r/min, 2x8pcs Bucket lifting speed 21.9m/min Mixing motor model & power y225s-4, 37kw Hoisting motor model & power yez160s-4, 15kw Water pump model & power kqw65-100i, 3kw Js1000 twin-shaft concrete mixer Capacity: 50m3/hr Discharging volume: 1000l Charging volume: 1600l Mixing motor: 37kw Reasonable js1000 concrete mixer Js1000 concrete mixer is dual horizontal shaft concrete mixer, which can can work independently, also can be composed the concrete mixing plant with other matched equipment., and it can be applicable to large, medium and small precast concrete products factory and roads, railways, bridges, water conservancy, civil construction project, and it can mix dry and hard concrete, plastic concrete, light aggregate concrete and all kind of mortar, it is one kind of high efficiency, widely used construction machinery. It owns reasonable design , and its mechanical accessories used industry standard parts, and its maintenance is much convenient. Nude cargo.Or based on customer's require
Qyc front-end fixed jacks have internal re-usable anchor which can automatically clamp and loosen the wedge, they are mainly used for bfm15 and bfm13- type various single tensioning with bonded and unbounded. Notice: qyc type front-end fixed jacks could be matched with different size, length of the top cover, retreat anchor device, to used in the experiment by root tension pre-tightening, tension retreat anchor and stay cable tone with single cable. Woode case.
The scopes Sap40-40tph Sap64-64tph Sap80-80tph Sap100-100tph Sap120-120tph In containers
Model Cap20Cap40Cap60Cap80 Cap20 tph40 tph60 tph80 tph In containers
Mb series mobile asphalt mixing plant is the latest generation asphalt mixing plant of sinosun group, based on quickly erection and easily transportation consideration. In containers
