Climbing rail cart is towed by winch or other vehicle. It runs on slope rail. It is used for transfer cargo from one level to another level. It is applied in the shipyard to handling workpiece. Stainless wheel, clamping device meet the special
Products Introduce The electric material transfer cart is powered by storage battery. The storage battery is installed in the electric material transfer cart. The storage batteries supplied the electricity to the DC motor through the electrical control system. Use this principle to operate the electric material transfer cart to starting, stopping, going forward, going backward, adjusting the speed and so on. Features Of Electric Material Transfer Cart 1. Battery power supply, operating distance is not restricted. 2. Can directly running on the concrete. 3. Turn to at will. 4. Change direction and route at any time. 5. Full load uninterrupted for 4-5 hours.
Products Introduce The steerable transfer vehicle for mold industry is powered by storage battery. The storage battery is installed in the steerable transfer vehicle. The storage batteries supplied the electricity to the DC motor through the electrical control system. Use this principle to operate the steerable transfer vehicle to starting, stopping, going forward, going backward, adjusting the speed and so on. Structures The whole steerable transfer vehicle is composed of motor, reducer, electric appliance and wheels. Due to more parts, compared with other transfer vehicle, it has large size. But it travels flexibly. url:http://www.newld-transfercar.com
Coil transfer car is used for steel coil, aluminum coil, paper roll etc coil cargo transportation. It powered can be rail, battery, cable drum, dragging cable etc. It can work on rails also can be work cement floor. There are coil holder mounted on the car and it is movable and can be removed. It can transport coils range 1-5 coils one time. The Load
Industrial Flat Transfer Cart Introduce This kinds of industrial flat transfer carts, the motor gear reducer as driving system of the carts, solid PU wheels of the industrial flat transfer carts can be run on the ground directly and flexibly with no limited running distance. And imported solid PU wheels can reduce the impair for the ground. It can be suitable for smaller space by 360 degree spot turning, 360 degree protection to guarantee site safety, including emergency stop., anti-collision device... touch-screen, Pry bar device,...this design is humanization and modernization. Automated operation makes the industrial flat transfer carts more intelligent.
Product Introduce The flanged rail steel wheels are made from high strength steel. Running surfaces are hardened to 40 HRC. With our own forging workshop, machining workshop, heat treatment workshop, we can provide all kind of wheels with different materials, such as ZG430640 cast steel, 60#,65 # , 65Mn, 42CrMoA or according to your demands. Specifications 1. Material: cast steel or cast iron. 2. Tread Hardness:260-380HB. 3. Loading capacity: 1-300 tons, can be customized. 4. Type : single flange wheel, double flange wheel, hollow wheel sets and solid wheel sets. 5. Diameter: 300mm, 350mm, 400mm, 450mm;500mm; 900mm, 1200mm, etc. Or as your demands. Inspection Technical report detailing the condition of each component to OEM requirements. Provide recommendations for repair or replacement. Issue recommendations to improve performance or capability. FIRM costs for reconditioning the assembly.
The steel industry transfer cart is powered by battery. The battery is installed in the cart. The batteries supplied the electricity to the DC motor through the electrical control system. Use this principle to make the transfer carts to start, stop, go forward, backward, adjust the speed and so on. Compare with conducting railway powered transfer carts and roll-cable powered transfer carts, this kind of battery powered steel industry transfer carts are more safe and flexible.
Product Introduction for 90 degree turntable The 90 degree turntable is a kind of turntable with a rotation angle of 90 degrees.Its special function is the common equipment in the rail transfer system. Features of 90 degree turntable The angle of rotation is 90 degrees; The 90 degree turntable can be divided into two categories: manual 90 degree turntable and electric 90 degree turntable; The loading capacity of the 90 degree turntable, can be customized according to customerâ??s demands.
Products introduce The kinds of electric railway flat vehicle, AC 380V voltage. In order to avoid the impair of cable, the cable drums are equipped together. Due to the limitation of cable length, it is suitable to be used in short distance transport system. It is a common equipment in workshop due to its simple structure, low price.
Brief Introduction for rail car turntable The weight and load of the rail flat car are the load of the rail car turntable. The rotation angle of the rotary table can be customized according to customer's demands, and can be realized to stopped at any angle of 360 degrees, and the well type cross operation can also be realized. The specifications of rail car turntable Product name: rail car turntable Type: manual turntable Capacity:Customized as per demands
The motorized flat rail carriage is cable drum powered, the motorized flat rail carriage gets power AC 380v through the device of cable drum, and the motor is controlled by the power through AC control system that make the motorized flat rail carriage to starting, stopping, going forward and going backward, adjusting the speed and so on. We adopt the magnetic coupling cable drum, it can make sure that there is no force on the cable and the cable can be wound and released evenly. if it is used in short distance transportation, it is a better choice without limited time. Of course, our product includers five kinds of different power, the proper solution will be recommended to you after
Motorized Material Handling Cart Introduce The motorized material handling carts are powered by battery. The battery is installed in the motorized material handling cart. The batteries supplied the electricity to the DC motor through the electrical control system. By this way, we can make the cart to starting, stopping, going forward, going backward, adjusting the speed and so on. Special Requirements Of Motorized Material Handling Cart Is Allowed The hydraulic lifting device can be equipped as per your requirement. As per the transported cargoes, the V frame, U frame, rubber pad, wooden pad, weighing device...can be equipped.
Products Description The kinds of electric transfer rail trolley, which is powered by conductor railway. It makes the AC electricity power is transformed into AC 36v three-phase and are respectively connected to the three rails. Then the electric transfer rail trolley conduct the AC 36v on rail into the electrical appliance box at the bottom of the trolley. And then the AC 36v is transformed into DC 36v to control the DC motor. Use this principle to make the electric transfer rail trolley start, stop, go forward and backward and adjust the speed and so on.
Rail Guided Flat Vehicle,it makes the AC electricity power is transformed into AC 36v two-phas and are respectively connected to the two rails. Then the flat vehicle conduct the AC 36v on rail into the electrical appliance box at the bottom of the vehicles. And then the AC 36v is transformed into DC 36v, control the DC motor through the DC control system to make the rail guided flat vehicle start, stop, go forward and backward and adjust the speed and so on.
Product Introduction for railway manual turntable The railway manual turntable is a device that turns and changes direction for the rail transfer cart on the rail, or material, equipment. It is installed in the position where the two rails are crossed, one or more rails are laid on its table. The upper surface of the turntable rails as same high as the upper surface of the track on the ground, and also has the same rail gauge. Advantages of railway manual turntable 1.Simple structure, low cost processing materials; 2.Production process is simple, easy to install; 3.Can be reused many times, less maintenance;
Working principle of agv electric turning vehicle AGV electric turning vehicle is composed by power supply system, navigation system, transmission system, steel structure frame, steering system, travelling mechanism, automation control system, signal feedback system and fault diagnosis system. As usual, this electric turning vehicle adopts battery as power source, through electrical control module system supply power to the traction motor, realize the AGV electric turning vehicle start, stop, forward, backward and steering, and other functions. Features of agv electric turning vehicle a. This kinds of agv electric turning vehicle needn't run via the rails, which gets rid of relying for the rails. b. It can not lead to impairment for the cement ground, and can run freely, go forward, back forward, turning... c. This kinds of agv electric turning vehicle is battery powered, so only charged fully, can it run freely without limited distance. d. Professional team for Xinxiang New Leader Machinery Manufacturing Co., Ltd,, the proper solution can be provided once getting for your inquiry. e. The agv electric turning vehicle can be customized as per your true demand. Application of agv electric turning vehicle The agv electric turning vehicle is suitable for various occasions, for example,industries, (steel mill, transfer steel products such as steel structure, steel pipe, steel billets, steel ladle and coil, etc from one location to another; Paper roll plant: transfer paper coil Painting shops: transfer work piece into the painting room Sand blasting room), Workshops, automotive molds, material handling, aerospace equipment workshops, air-conditioning workshops,
Products Introduce The railway transfer vehicle is the cable reels powered, the railway transfer vehicle gets power AC 380v through the device of cable reel , and the motor is controlled by the power through AC control system that make the railway transfer vehicle to start, stop, go forward , backward , adjust the speed and so on. We adopt the magnetic coupling, it can make sure that there is no force on the cable and the cable can be wound and released evenly. if it is used in short distance transportation. It is a better choice without limited time. Of course, our product includers different power, the proper solution will be recommended to you after learning your requirements. Features The railway transfer vehicles can run on the straight railways to carry many material, workpiece, workpiece; The railway transfer vehicles can be applied in many occasions, such as easy explosion, easy corrasion, high temperature; AC motor, simple structure, not limited for the using time; This kinds of railway transfer vehicle is powered by cable reels, so there is not strict requirement for the construction of the railway, and the running distance should accord to the length of the cable; Cost is not high, easy to operate and maintenance;
Working Principle of electric rail turntable The principle of the electric rail turntable is to rotate the gear by the motor to achieve the rotation of the turntable. When the flat car is completely running on the turntable, the turntable starts to rotate to the desired angle and the connect with the ground rails completely, then the flat car can starts again and runs along the rails. Advantages of electric rail turntable A very common device in the rail transportation system; We can design the capacity, rotation degree as requirement; Adopts electric drive mode and frequency control; Positioning safety requirements are high, there are mechanical and electrical two control methods for braking;
Product Introduction for factory electric turning vehicle The factory electric turning vehicle is a solution for transportation design on S-shaped, C-shaped and U-shaped rails. The wheels with steering mechanisms that can adapts to the curved rail and ensure the wheel edge do not rub against the rail. At present, the customer of factory electric turning vehicles are increasingly diversified. The functions of the factory electric turning vehicles are not limited to the load, and the operating lines are diversified. There are various forms distributed, such as straight lines, curved bends, S bends, right angle bends, climbing slopes and so on. Quality Control for factory electric turning vehicle 1. Configure single audit, customer demand is the primary choice, customer demand is the main basis for cost performance; 2. Examination of construction drawings, construction drawings provide an important basis for production and processing, require reasonable and precise drawings, and plan approval; 3. Under the material audit, request the correct input, the thickness is correct; 4. Assembled welding examination requires standard size chain, reasonable and orderly processing according to the figure, no slag, uneven, cracks, etc.; 5. After grinding and rusting inspection, the vehicle shall not appear sharp corners, burrs, or rust dead spots except under special circumstances; 6. The assembly assembly audit is strictly in accordance with the requirements of the contract industry standards, industry common sense, etc.; 7. Spray paint examination, requiring the use of precision paint, spray paint uniform, beautiful and generous; 8. Electrical installation requires correct position, firm installation, and correct wiring.
Product Description Cross-bay steering handling vehicle is a kind of rail transfer vehicle which can solve the problem of product transportation between factory spans. It is also called rail flat vehicle, electric rail transfer vehicle, material handling vehicle and so on. The cross-bay steering handling vehicle is running on the rails and powered by mobile cable. Working Principle When the cross-bay steering handling vehicle moves, the cable pulls behind the cross-bay steering handling vehicle. The cable is connected to the ground at one end, while the other is powered by an electric control box on cross-bay steering handling vehicle, and then provide the power to the engine. The cross-bay steering handling vehicle conduct AC 380V directly into the electrical control system of the cross-bay steering handling vehicle to let it start, stop, go forward and backward and so on. Safety Device 1. Acousto-optic warning lamp(When the cross-bay steering handling vehicle is running, it will ring up to warn others) 2. Urgent stop button(When encountering unexpected situations, pressing the emergency stop button, the cross-bay steering handling vehicle will immediately stop to ensure safety) 3. E-stops (The induction switch equipped on the front and rear of the cross-bay steering handling vehicle, the vehicle will automatically stop when induction of obstacles, to ensure safe)
