Product description Transformer Standard current transformer are also called precision current transformers, current transformer standards, standard CT and current transformer standards. Transformer standards are divided into current transformer standards and voltage transformer standards. Standard current transformers are used in the error test of transformers. Used as a current transformer calibration standard technical parameter 1. Temperature: 2. Relative humidity 3. Rated Primary Current:5-5000A 5A,1A 4.Rated secondary current:5 1A 5 Accuracy Class 0.05S 6. Allow long-term work under the rated current; More than120A across the core. Precautions: 1. The current of standard CT and tested CT must be the same in CT calibration. 2. Follow the given wiring diagram strictly. 3. Test whether the load box is accurate or not before calibrating the transformer. 4. Forbid secondary winding opening during the calibration. 5. Select demagnetization before calibration.The wiring diagram is shown in figure 5. Short out the secondary winding before cutting off the power when the demagnetization is finished. 6.Principle wiring diagram of CT with large current generator is similar to above diagram. They are the same except the output winding of large current generator and primary winding of transformer are the same one.
Product Introduction Capacitive voltage transformer (CVT) in calibration the test must be conducted under the condition of 50Hz frequency complex geographical condition on site at the same time the traditional experiment device is difficult to meet the requirements of on-site handling testing series resonance booster device is first used in domestic field tunable resonance device has been widely used in domestic 500 kv and below the field calibration of capacitor voltage transformer. Product Parameters Technical parameters Rated Capacity 80kVA rated voltage 160kV Adjustable inductance range 65~130H Rated frequency 50Hz Rated current 0.5A Adjustable gap range 0~300mm
Product description Transformer Standard current transformer are also called precision current transformers, current transformer standards, standard CT and current transformer standards. Transformer standards are divided into current transformer standards and voltage transformer standards. Standard current transformers are used in the error test of transformers. Used as a current transformer calibration standard technical parameter Temperature -5 40 Relative humidity 80% Rated Primary Current 5-5000A 5A,1A Rated secondary current 5A 1A Accuracy Class 0.05S Allow long-term work under the rated current; More than120A across the core. Precautions The current of standard CT and tested CT must be the same in CT calibration. Follow the given wiring diagram strictly. Test whether the load box is accurate or not before calibrating the transformer. Forbid secondary winding opening during the calibration. Select demagnetization before calibration.The wiring diagram is shown in figure 5. Short out the secondary winding before cutting off the power when the demagnetization is finished. Principle wiring diagram of CT with large current generator is similar to above diagram. They are the same except the output winding of large current generator and primary winding of transformer are the same one.
Product description The current booster is used on checking current transformer,to be the power source supply once current for current transformer or to be other 50Hz single phase current source device. Technical index Temperature Humidit Capacity: 20kVA Specification Weight: 75Kg Allow long-term work on the rated current Allowable overload 1.5 times,30 minutes of continuous work. Feature This PSLLQ is make up of input Winding(220V), output winding below 100A and CXRZ. Output current indicated on the nameplate is defined the rated current that through winding allow to pass.When CX many circles, the rated current its permitted to pass through will inversely decline. The value which ouput capcity divided by product of output current and each circle voltage was the biggest circle number allowing. The current booster is designed to provide the primary current power supply for the current transformer when verifying the current transformer or as other 50HZ single-phase power equipment. The current booster for transformer verification is suitable for power departments such as power testing, power measurement, and power maintenance. The current booster is developed and produced according to the industry standard of transformer error testing, and is used as a current transformer to verify the primary current of the current transformer. The output current can be customized according to customer requirements. The lifter is equipped with casters for easy on-site movement.
Wireï¼?electrical cableï¼?electrical wireï¼?electrical cord reelsï¼?coil cordsï¼?cable.
Laser Diode Or Photodiode Aging Socket, Chip Loading Fixture And Laser Aging Plate, Etc.
GRP Pipe Filament Winding Prodcution Line-Winding Machine GRP Pipe Winding Machine Specifications: General technical data: Diameter range DN300mm-3000mm Length of Product 12m Winding Angle 45° - 90° Carriage stroke 13m Control Manner Two axes motion and three spindles Electrical power supply 380V, 3 phases 50-60 Hz Raw materials: Resin Polyester resin, or vinyl ester resin with reinforcement yarn E-Glass or ECR Roving 1. Liner making machine(13 Kw/set) (1set) Consist of: 1) Headstock 1 set 2) Tailstock 1 set 3) Railway 1 set 4) Carriage 1 set 5) Four-wheel pneumatic roller 1 set 6) Mylar delivery rack 1 set 7) System of timing with frequency conversion 1 set 8) Electric control system 1 set 9) Resin feeding system 1 set
Super tank Polymer Concrete Electrolytic Cells are designed, built and installed to satisfy the most stringent requirements requested by tank house operators worldwide. In most case their main request is to guarantee full operating availability throughout the plant' s lifespan, maximizing production of high-purity metal (copper, zinc, nickel, cobalt, lead or other) with absolute safety for people and the environment. Additionally, Polymer Concrete Electrolytic Cells must accommodate changes for continuous improvement of electrolytic process, integrating efficiently with upgrades of complementary equipment such as anodes, cathodes, cap boards, overhead crane, electrolyte agitation systems, acid mist control devices, thermal insulation, among many others. Super tank electrolytic cells are cast monolithically based on a patented, three stratum composite material system. the internal stratum is a monolithic tank made with multiple layers of fiber-reinforced vinyl ester resin (FRP) complying with chemical barrier international norms that assure long term impermeability and corrosion resistance. the intermediate stratum is the structural core made with Hyperbonded Polymer Concrete, with a patented formulation to achieve a low coefficient of thermal expansion, providing long term structural integrity with low thermally-induced stresses. the external stratum is a standard seal layer of FRP that further protects the structural core from electrolyte splashes and spills. Optionally, this external seal may be specified with multi-layered oriented fiber reinforcements to guarantee trouble-free operation in unusually extreme operating environments.
Super tank Polymer Concrete Electrolytic Cells are designed, built and installed to satisfy the most stringent requirements requested by tank house operators worldwide. In most case their main request is to guarantee full operating availability throughout the plant' s lifespan, maximizing production of high-purity metal (copper, zinc, nickel, cobalt, lead or other) with absolute safety for people and the environment. Additionally, Polymer Concrete Electrolytic Cells must accommodate changes for continuous improvement of electrolytic process, integrating efficiently with upgrades of complementary equipment such as anodes, cathodes, cap boards, overhead crane, electrolyte agitation systems, acid mist control devices, thermal insulation, among many others. Super tank electrolytic cells are cast monolithically based on a patented, three stratum composite material system. the internal stratum is a monolithic tank made with multiple layers of fiber-reinforced vinyl ester resin (FRP) complying with chemical barrier international norms that assure long term impermeability and corrosion resistance. the intermediate stratum is the structural core made with Hyperbonded Polymer Concrete, with a patented formulation to achieve a low coefficient of thermal expansion, providing long term structural integrity with low thermally-induced stresses. the external stratum is a standard seal layer of FRP that further protects the structural core from electrolyte splashes and spills. Optionally, this external seal may be specified with multi-layered oriented fiber reinforcements to guarantee trouble-free operation in unusually extreme operating environments.
Super tank Polymer Concrete Electrolytic Cells are designed, built and installed to satisfy the most stringent requirements requested by tank house operators worldwide. In most case their main request is to guarantee full operating availability throughout the plant' s lifespan, maximizing production of high-purity metal (copper, zinc, nickel, cobalt, lead or other) with absolute safety for people and the environment. Additionally, Polymer Concrete Electrolytic Cells must accommodate changes for continuous improvement of electrolytic process, integrating efficiently with upgrades of complementary equipment such as anodes, cathodes, cap boards, overhead crane, electrolyte agitation systems, acid mist control devices, thermal insulation, among many others. Super tank electrolytic cells are cast monolithically based on a patented, three stratum composite material system. the internal stratum is a monolithic tank made with multiple layers of fiber-reinforced vinyl ester resin (FRP) complying with chemical barrier international norms that assure long term impermeability and corrosion resistance. the intermediate stratum is the structural core made with Hyperbonded Polymer Concrete, with a patented formulation to achieve a low coefficient of thermal expansion, providing long term structural integrity with low thermally-induced stresses. the external stratum is a standard seal layer of FRP that further protects the structural core from electrolyte splashes and spills. Optionally, this external seal may be specified with multi-layered oriented fiber reinforcements to guarantee trouble-free operation in unusually extreme operating environments.
Ur large size of batteries, 18 months for our small size batteries. 4.Various payment: we can accept various payment terms, like tt, l/c and so on. 5.Various type: we manufacture types is very widely, can for ups, e-bike, storage , and telecommunications and so on. 6.Good service: we with specialized person who work for battery marketing more than eight years for good communications. 7.Rich experiences: we have rich experiences to do the oem brand for you to keep you every details as your required. 8.Worldwide customer: wherever you are, all with our stable customer exist for your reference Product advantage: 1free maintenance: the battery is free maintenance, you can use it till the life is the end. 2low discharge rate: the battery with very lower self-discharge, you can store it more than 3 months. 3adaptable condition: the battery design can suite for various conditions, like different temperature.
1. Battery charger 1. Professional mount: according to anton/bauer product, install with gold mount("a" type mount), and the link is safe and reliable. 2. Fast charge system: many batteries can be charged simultaneously, double, voltage 16.8v, current is 2 a; 4 batteries, voltage 16.8v, current is 1.5a 3. Input voltage: ac100~240v 4. Adapter output: 12v 50w 5. Dc power function: as an adapter. Can offer dc 12v power supply for camera. 6. Lcd display function: charge voltage, battery capacity, current, cycle times, model, manufacture date, temperature etc. 7. Perfect protection function: according to the characters of the battery, the charge system provides suitable charging process for the battery. 8. Light design is easy to carry 9. Comhensive use for camera 10. High quality, competitive price Weight:2.0kg Dimension: 232*285*90
1. Battery charger 1. Professional mount: according to anton/bauer product, install with gold mount("a" type mount), and the link is safe and reliable. 2. Fast charge system: many batteries can be charged simultaneously, double, voltage 16.8v, current is 2 a; 4 batteries, voltage 16.8v, current is 1.5a 3. Input voltage: ac100~240v 4. Adapter output: 12v 50w 5. Dc power function: as an adapter. Can offer dc 12v power supply for camera. 6. Lcd display function: charge voltage, battery capacity, current, cycle times, model, manufacture date, temperature etc. 7. Perfect protection function: according to the characters of the battery, the charge system provides suitable charging process for the battery. 8. Light design is easy to carry 9. Comhensive use for camera 10. High quality, competitive price Weight:1.5kg Dimension:255*111*83
1. Battery charger 1. Professional mount: according to anton/bauer product, install with gold mount("a" type mount), and the link is safe and reliable. 2. Fast charge system: many batteries can be charged simultaneously, double, voltage 16.8v, current is 2 a; 4 batteries, voltage 16.8v, current is 1.5a 3. Input voltage: ac100~240v 4. Adapter output: 12v 50w 5. Dc power function: as an adapter. Can offer dc 12v power supply for camera. 6. Lcd display function: charge voltage, battery capacity, current, cycle times, model, manufacture date, temperature etc. 7. Perfect protection function: according to the characters of the battery, the charge system provides suitable charging process for the battery. 8. Light design is easy to carry 9. Comhensive use for camera 10. High quality, competitive price Weight:1.7kg Dimension:233*207*83
LS14250 LS14250 ER14250 TL-2150 TL-2150 TL-2150 ER14250 E14250 TL-2150 ER14250 ER14250 TL-2150 ER14250 TL-2150 ER14250 LS14250 LS14250 ER14250 TL-2150 ER14250 Ms CoCo 13986282065 0086-27-83258996 . 23.5x28.5x32.5 cm.
Battery type : li-ion Voltage : 11.1v Capacity : 3600mah Product type : replacement battery (brand new) Product id : epmn001 Replace code : smp-202 Voltage : 11.1v Capacity : 3600mah
3.6v li/socl2 er14505h size aa bobbin type Specification: Max dimension: 14.5x50.5mm; Nominal capacity: 2700mah (1ma/2.0v); Nominal voltage: 3.6v; Max constant discharge current: 50ma; Max pulse current: 150ma; Operating temperature range: -55½+85 Er14505h can replace tl-5903 ls14500 ls14500c tl-4903 tl-2100 xl-060f sl-360 sl-760 Primary lithium battery type er14505h has the advantages of high energy density, high open circuit voltage, wide range of operating temperature, stable operating voltage and current (over 90% of the total capacity is discharged at a high plateau voltage), long operating time (over 8 years) for continuous low current discharge with medium current pulse and low self-discharge rate (less than 1% per year). Its main applications are : utility meters, main-frame computers, pcs, gps, wireless communication, asset tracking , law enforcement, earth detector, digital control machine, portable communication equipment, military radio stations, and other electric powered devices requiring small current drain high current pulse long operating life applicable batteries.
Primary lithium battery Specification: Max dimension: 17.0x50.5mm; Nominal capacity: 3400mah (2ma/2.0v); Nominal voltage: 3.6v; Max constant discharge current: 100ma; Max pulse current: 200ma; Operating temperature range: -55½+85 Er17505 can replace ls17500 xl-100f sb-a01 Primary lithium battery type er17505 has the advantages of high energy density, high open circuit voltage, wide range of operating temperature, stable operating voltage and current (over 90% of the total capacity is discharged at a high plateau voltage), long operating time (over 8 years) for continuous low current discharge with medium current pulse and low self-discharge rate (less than 1% per year). Its main applications are : utility meters, main-frame computers, pcs, gps, wireless communication, asset tracking , law enforcement, earth detector, digital control machine, portable communication equipment, military radio stations, and other electric powered devices requiring small current drain high current pulse long operating life applicable batteries.
3.6v li/socl2 er26500 size c bobbin type Specification: Max dimension: 26.2x50.0mm; Nominal capacity: 7500mah (3ma/2.0v); Nominal voltage: 3.6v; Max constant discharge current: 230ma; Max pulse current: 400ma; Operating temperature range: -55íµí½+85íµ Er26500 can replace ls26500 tl-5920 tl-4920 xl-145f tl-2200 sl-2770 sl-780
Gfm series valve regulated lead acid battery Features Super cell capacity Avoid some trouble that is caused by connecting several internal cells in parallel when the capacity of the battery reaches 4000ah. Long life design Special heavy-duty lead-calcium alloy remaining the float charge life more than 10 years. Full capacity Use tank formation technology to improve the first cycle 10hr capacity more than 100%. Excellent high rate discharge performance Use large area copper terminal with patent construction and special high porosity plate to ensure high rate energy output. Low self-discharge rate Use high quality and high pure raw material to reduce the self-discharge rate not more than 0.08% per day. Maintenance-little Use agm absorption technology and oxygen recombination technology to ensure more than 99% oxygen being recombined and not needing to add the water. Safety The patent technology with double post sealing construction and valve adjusting technology ensure the battery has no leakage and no acid mist flood and explosion-proof. Easy installation Use portable and flexible copper cable to connect the battery and it is ease to install due to use all kinds of cabinet and rack construction. Being economical The battery adopts the valve regulated sealed construction, no acid mist flood and not needing special accumulator room. And it can be placed with other power supply device in the same room. Standard carton and wooden package
