This device adopts advance ARM+FPGA high precision D/A conversion and DDS technologies can set up and regulate parameters of voltage current frequency phase etc in a long period of time via analog closed loop feedback and digital PID control 1. Can be used to test errors and variance caused by voltage current waveform or power factor change for a variety of metering instrument such as energy meter voltmeter ammeter wattmeter frequency meter power factor meter phase meter 2. Can generate distorted wave with 2~32 order harmonic harmonic number order amplitude and phase position to base wave can be controlled by programs 3. Operational amplifier work frequency 40HZ~1kHz good linearity dual output protection High fidelity output signal and high shock-proof ability 4. With RS232 and USB(optional) communication interface for PC connection 5. With aluminum alloy carrying box which look nice and with little weight
1. Function: AC sampling device and sampling RTU (Remote Terminal Unit) calirbation 1) AC/DC analog value input measurement 2) state variables input measurement 3) remote control execution testing 4) remote regulation function testing 5) digital value input testing 6) impulse input testing 2. AC Power source It can output AC voltage AC current accuracy 0.05 class can provide standards of AC/DC voltage/current power phase power factor frequency energy. Output method and output electric quantity can be set arbitrarily 3. Data management It can save search browse print or delete RTU testing data. Calibrated parameters can be saved permanently
product brief introduction Product Introduction Alternating and direct current amphibious light AC DC Hipot Test Set. The winding is theconcentric pagoda and multilayer cylindrical type low-voltagewinding in inner high-voltage winding in outside; Outer cover is portable which has characteristics such as volume smallness weight light the shape prettiness and move convenience and so on. Product Parameters technical parameters environment temperature 0ï½?40â?? altitude < 100m relative humidity < 85% Main product specifications type specification capacity power source output operating mode Refer to the weight anthroposcopy (V) (A) (V) (A) XC-2 2 1 220 50 0-220 10 manual operation 14 XC-3 3 1 220 50 0-220 15 manual operation 16 XC-5 5 1 220 50 0-220 20 manual operation 18
product brief introduction Product Introduction TC power frequency voltage tester adopts integrated design, small size, light weight, more convenient for transportation and portable operation. The over-current protection of voltage tester is set by current relay, The high-voltage output, direct reading instrument and operation are integrated with the voltage stand. Therefore, the operation is simple, practical and reliable.
Product description Single phase standard power supply is suitable for power department, quality control department, research units, institution of higher learning, electric energy meter, power supply management, load control, power quality, reactive power compensation device and production of the enterprise and so on. It can be as single phase voltage source, current source and power source. Electrical parameters Electrical parameters Accuracy class 0.05, 0.1 Power supply Single phase AC 85-265V, 50 60 Hz AC Voltage output Range 57.7V 100 V 220V 380V, Switch automatically max 500V Adjustment resolution 0.01, 0.1, 1 10,
Product description Single phase standard power supply is suitable for power department, quality control department, research units, institution of higher learning, electric energy meter, power supply management, load control, power quality, reactive power compensation device and production of the enterprise and so on. It can be as single phase voltage source, current source and power source. Electrical parameters Electrical parameters Accuracy class 0.05, 0.1 Power supply Single phase AC 85-265V, 50 60 Hz AC Voltage output Range 57.7V 100 V 220V 380V, Switch automatically max 500V Adjustment resolution 0.01, 0.1, 1, 10 AC Voltage output Range 57.7V 100 V 220V 380V, Switch automatically max Adjustment resolution 0.01, 0.1 1, 10, Accuracy 0.05 RG Stability Better than 0.01 RG 1min Distortion degree Better than 0.1 not capacitive load Load capacity 40VA Full load regulation rate Less than 0.01 RG Full load regulation time Less than 1ms Temperature drift 8 PPM C Long-term stability 60 PPM year
Generator sets.
Ws wt 400w small wind turbine applies to those places where the wind source is better and inconvenient utility electricity, Ment lighting fields is very conspicuous. It not only makes full use of Nature energy but also add beautiful nature landscape. A. Wind/solar hybrid street lighting power system. B.Industry, agriculture, business, university, military, animals, forestry, fishing lighting power system, etc. C. Communication base station D. Road monitoring E. Household Technical information: Components of wind turbine and technical information Start wind speed 1.5m/s Rated wind speed 12m/s Cut-in wind speed 2m/s Rated voltage 12v/24v Rated power 400w Max power 4500w Fan material Southwest aluminum Number of fan 6 Fan diameter 320mm Safe wind speed 40m/s Whole weight 15kg Environmental conditions unlimited Temperature Wind turbine is -20~+85¡ãc Humidity Wind turbine is ¡Ü90% Altitude ¡Ü4500m(rated altitude condition is 1000m) Max wind speed ¡Ü35m/s, instantaneous maximum wind speed ¡Ü50m/s Wind turbine installation height 3.5m~13m Output power Wind speed Output power 2m/s 1.5w 4m/s 10w 7m/s 80w 8m/s 100w 9m/s 150w 10m/s 250w 12m/s 350w Above 15m/s 450w Note: wind speed exceeds 15m/start electronic speed brake system Packing: 1pc/ctn
400w ~ 800w£¡§12v/24v£© Charge off voltage hvd 14.4v / 28.8v Low voltage directive lvd 10.8v / 21.6v Low voltage restore lvr 11.8v / 23.6v Charge loop drop £¼300mv Discharge loop drop £¼50mv Overload protection 31.5v Short-circuit protection 30a Light operate Light control on + light control off Light time control Light control on/off + time control on/off Time control classification 0.5 hours started, half an hour of one grade, up to 10 hours Output route Single bulb Ambient temperature -25¡æ¡ª¡ª+55¡æ Safe degree Ip55 Quiescent dissipation 24ma Wind turbine braking mechanism Unloading brake Control mode Solar charge/ Specification: 40pcs/carton
Product description The impulse voltage generator intelligent measurement and control system is the latest programmable control system and consists of two parts: Automatic control of pulse voltage generator program and automatic analysis of pulse signal measurement. The General Conditions of Use Altitude: 1000m Ambient temperature: -5 40 Relative humidity: 90 20 Use of the environment: indoor Non-conductive dust Grounding resistance 0.5 No fire or explosion hazard Earthquake resistance: 8 magnitude There is no gas that corrodes metal and insulates Impulse voltage generator (2) Supply voltage waveform is the actual sine wave, waveform distortion rate 85% (more than 90% when no load 300PF); (2)Truncated wave: cut-off time (2-6) 10% s, zero-crossing coefficient 0.3% (3)Standard operating impulse voltage wave 250 20% s / 2500 60% s, The impulse voltage waveform parameters and their deviations are in line with the requirements of the national GB311 and GB16927 standards. 7, the lowest output voltage is greater than 10% of the nominal voltage 8. Duration of use: Above 70% of rated voltage, it can be continuously operated every 120 seconds after charging and discharging. It can be continuously operated after charging and discharging every 60 seconds under 70% of rated voltage. One computer is used for control and waveform analysis 18-inch LCD monitor, strong anti-interference and long life WINDOWS XP, OFFICE 2003, LabVIEW related driver software, ACE measurement and control software package,built in
Products Introduction Ultra-low frequency dielectric strength testing is another method of power frequency withstand voltage testing, because large-capacity testing is required, and large-scale equipment is not only expensive, but also bulky. The power department did some tests to solve these problems. According to domestic and foreign tests, this product can solve this problem. Not only the size of the instrument is small, but the weight is greatly reduced. Precautions When carrying out 35KV cable test, one-phase test is strongly suggested. Voltage is set to 60KV (General Requirements)-78KV (according to the rules needed) and the frequency is set to 0.1Hz, 0.05Hz,0.02Hz and 0.01Hz. The manual said load capacity is the theoretical value, the scene 35KV cable length can reach 3-15 km. In case the cable is too short(less than 500 meters), the capacitance of the test object is smaller than 0.1 F and the pressure cannot be normally boosted, please connect 0.1 F high-voltage capacitance in parallel way. Keep high-voltage terminals nylon spin by the above numbers to the corresponding nylon seat, high-voltage lines to ensure good contact , no contact is good , it will cause a discharge , burned the high side . When nylon terminals tightened, pay attention to the intensity, excessive tightening may damage the nylon terminals. 80KV 0.1HZ VLF high voltage generator Model Rated Voltages Load capacity Fuse Weight Useful VLF-80 80kV (peak ) 25A
Product description The impulse voltage generator intelligent measurement and control system is the latest programmable control system and consists of two parts: Automatic control of pulse voltage generator program and automatic analysis of pulse signal measurement. The General Conditions of Use Altitude: 1000m Ambient temperature: 5 40 Relative humidity: 90 20 Use of the environment: indoor Non-conductive dust Grounding resistance 0.5 No fire or explosion hazard Earthquake resistance: 8 magnitude There is no gas that corrodes metal and insulates Impulse voltage generator (2) Supply voltage waveform is the actual sine wave, waveform distortion rate 85% (more than 90% when no load 300PF); (2)Truncated wave: cut-off time (2-6) 10% , zero-crossing coefficient 0.3% (3)Standard operating impulse voltage wave 250 20% s / 2500 60% s, The impulse voltage waveform parameters and their deviations are in line with the requirements of the national GB311 and GB16927 standards.
Overview Three-phase phase volt-ampere meter a high precision instrument for measurement of three-phase electric parameters, it can be used to measure the three phase voltage, current and phase angle, frequency, power, power factor and so on. three-phase digital volt-ampere phase meter adopt high-speed Cortex M3 processor and 24 bits high-speed ADC a for measuring and calculation , A complete graphical interface, true color display with resolution of 320 x 240 and touch screen operation make a friendly man-machine interface. It is easy to carry
Products Introduction Very Low Frequency high voltage generator 30KV combines advanced technologies such as modern digital conversion, full computer control, automatic voltage increase, voltage reduction, measurement and protection. In the automatic upgrade process, human intervention can be taken care of. The main advantages include full electronics, small size, light weight, large-screen LCD display (clear and intuitive), printer output test report, and easy use. Technical Parameter
Product description The impulse voltage generator intelligent measurement and control system is the latest programmable control system and consists of two parts: Automatic control of pulse voltage generator program and automatic analysis of pulse signal measurement. The General Conditions of Use Altitude: 1000m Ambient temperature: -5 40 Relative humidity: 90 20 Use of the environment: indoor Non-conductive dust Grounding resistance 0.5 No fire or explosion hazard Earthquake resistance: 8 magnitude There is no gas that corrodes metal and insulates Impulse voltage generator (2) Supply voltage waveform is the actual sine wave, waveform distortion rate 85% (more than 90% when no load 300PF); (2)Truncated wave: cut-off time (2-6) 10% , zero-crossing coefficient 0.3% (3)Standard operating impulse voltage wave 250 20% s 2500 60% s,
Products Introduction VLF high voltage generator 60KV.The capacity of it is 1/500 of tradition way. Greatly simplify testing procedures, That is why commonly used in the developed , s ministry of electric power entrust Wuhan high voltage research institute to drafting 35Kv and below XLPE insulated power cable ultra-low frequency (0.1Hz) voltage withstand test methods for promoting this approach. The instrument is developed according to made of this need. It can be widely used in cable, large-scale high-pressure rotary motor, power capacitors into AC voltage withstand test. Power capacitance of single-core XLPE insulated cable (F/km) 0.1Hz -60KV Ultra-Low Frequency High Voltage Generator Model Rated Voltages Load capacity Fuse Weight Useful VLF-60 60kV (peak ) 0.1Hz,0.5F 25A Control 6 HV TANK-30 HV TANK-II33 25KV and below the cable
Product description The impulse voltage generator intelligent measurement and control system is the latest programmable control system and consists of two parts Automatic control of pulse voltage generator program and automatic analysis of pulse signal measurement. The General Conditions of Use Altitude 1000m Ambient temperature 5 40 Relative humidity 90 20 Use of the environment indoor Non conductive dust Grounding resistance 0.5 No fire or explosion hazard Earthquake resistance 8 magnitude There is no gas that corrodes metal and insulates Impulse voltage generator 2 Supply voltage waveform is the actual sine wave, waveform distortion rate 85 more than 90 when no load 300PF 2 Truncated wave cut-off time 2-6 10 s, zerocrossing coefficient 0.3
Overview Three phase phase volt-ampere meter a high precision instrument for measurement of three phase electric parameters, it can be used to measure the three phase voltage, current and phase angle, frequency, power, power factor and so on. three phase digital volt-ampere phase meter adopt high-speed Cortex M3 processor and 24 bits high-speed ADC a for measuring and calculation , A complete graphical interface, true color display with resolution of 320 240 and touch screen operation make a friendly man-machine interface. It is easy to carry Specifications TYPE MEASUREMENT RANGE UNIT ERROR RESOLUTION RATIO Voltage 1 600 V 0.5 measuring range 0.01V Current 0.001 10 A 0.5 measuring range 0.0001A active power 0.001 5000 W 0.5 reading PF 1 0.1W reactive power 0.001 5000 VAR 0.5 reading PF 0 0.1VAR apparent power 0.001 5000 VA 0.5 reading 0.1VA frequency 45 65 HZ 0.1 reading 0.01HZ phase position 0 360 2 0.1
Products Introduction The power department did some tests to solve some problems. According to theories and test results at home and abroad, the 50KV Very Low Frequency high voltage generator withstand voltage test can solve this problem. Its advantages are that not only the test results are the same, but the instrument size is small and the weight is greatly reduced. output rated voltage power fuse Refer to the following table Model Rated Voltages Load capacity Fuse Weight Useful VLF-50 50kV (peak ) 0.1Hz,â?¤1.1�µF 20A
The impulse voltage generator intelligent measurement and control system is the latest programmable control system and consists of two parts: Automatic control of pulse voltage generator program and automatic analysis of pulse signal measurement. The General Conditions of Use Altitude: 1000m Ambient temperature: -5 ~ +40 Relative humidity: 900 Use of the environment: indoor Non-conductive dust Grounding resistance < 0.5 �© No fire or explosion hazard Earthquake resistance: 8 magnitude There is no gas that corrodes metal and insulates
