Elevator, escalator, lift, cargo lift, moving walkway, elevator parts, dumbwaiter lift, passenger elevator, glass lift, passenger lift, panoramic lift, bed elevator, fuji lift, fuji elevator.
Professional supplier of inulin, erythritol, sodium erythorbate, msg, l valine, l leucine, l isoleucine, l glutamine, l histidine, l theanine, l tryptophan, l threonine, hyaluronic acid, gellan gum, pectin, xanthan gum and bcaa..
Petrochemicals,refining additives,refining catalysts,petroleum refining additives.Global sourcing,logistics and supply chain management,quality assurance and inspections, regulatory compliance support
Glass tube, epoxy fiberglass tube, glass fiber wound tube, fr4 tube, winding tube, cross winding tube, fiber reinforced winding tube, epoxy tube.Glass tube,epoxy fiberglass tube,glass fiber wound tube,fr4 tube,winding tube,cross winding tube ,fiber reinforced winding tube,epoxy tube
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Auto diesel injection test equipment, such as the diesel pump test bench, common rail injector test bench, common rail pump test bench, common rail simulator.
brake pads,clutches, chains, connectors,bearings all types of spare parts are available
Ignition coil, module, regulator, distributor.
Reducer, worm gearbox, worm gear reducer.
Automobile electrical equipment.
Air inflating gun, air blow gun, tire pressure gauge, tire inflating pump, engine washing gun, spray gun, quick coupler.
Linear guides, ball screw, linear bearings, shaft, rod end bearings, cam follower roller bearing, igus bearings.Linear guides, ball screw, linear bearings, shaft, rod end bearings, cam follower roller bearing, igus bearings
gearbox, speed reducer, worm gearbox, harmonic drive, screw lift.
AC servo motor, AC servo driver, controller, PLC, gearbox, servo kit, servopack.
Auto car vehicle, body parts fender, hood, engine bonnet, door, bumper, light, grille, radiator, panel .
Tyres for aircraft aircraft seats aircraft parts.Trade
Aviation spare airparts.
Standard: a-a-59326(mil-c-27487) or din2828 Casting method: die casting or gravity casting Size: from 1/2" to 8" Type: b Body material: aluminium ( heat treated if need) Cam arm mate safety clips Gasket material: nbr, epdm, viton, ptfe envelope gasket, silicone Thread: npt and bsp (usually, female thread is bspp, male thread is bspt) Carton pallet
Product name: Transmission Gear Box For Toyota 2KD2TR 33030-26A01 price breakdown: automobile spare parts 1PC 50PC 200PC 1000PC USD500 USD495 USD490 USD480 Custom Gear Box for cars Material: Alumium Shipping: Stock and can deliver once payment received. We produde automobile spare parts,mainly including casting cylinder head, OEM Alloy steel crankshafts for cars ,custom Free Wheel Hub for cars ,Custom Gear Box for cars and soon automobile spare parts China Car Application Engine OEM NO Toyota 2KD 2TR 2TR 33030-26A01
ZLYJ Series Gearboxes for Plastic and Rubber Single Screw Rod Extruder is a kind of special reducer researched and developed by importind the most advanced technology of the hard teeth-surface in the world. For recent ten years, they are widely used in top and middle grade plastic, rubber and chemical fiber extruders, sell well in the country and are exported abroad. With a higher reputation in the industry, it has features as follows: 1. The whole machine looks beautiful and liberal, and can be used both vertically and horizontally. It can suit multiple requirement of assembling. 2. The gear data and box structure are optimally designed by the computer. The gears are made of top grade low carbon alloy steel with Grade 6 precision of teeth after carbon penetrating, quench and teeth grinding. The hardness of the teeth surface is 54 - 62 HRC. The gear pair has stable running, low noisy and has high driving efficiency. 3. The assembling connector has the precision of radial run-out and end face run-out at international level, and can be easily connected with screw rod of the machine barrel. 4. The bearing structure of the output shaft has a unique style, which can effectively prolong service life of the bearings. 5. All standard parts such as bearing, oil seal, lubricant oil pump etc. are all top quality products selected from domestic famous manufacturers. They can be also selected from imported products as per requirement of customer.