RTV Silicone for PCB board electronic-pouring Description of RTV Silicone for PCB board electronic-pouring: RTV Silicone for PCB board electronic-pouring is a room temperature/heating curing and molding organic silicone materials. This kind of two-component elastic silicone potting, designed to protect in harsh conditions of electronic products. silicon encapsulating glue used new technology without heating can cured, would be curing. When used according to 100:10 (weight ratio or the volume in the thorough mixing proportion of A and B two components, products will be in A certain time, form of the elasticity of curing buffer material. RTV Silicone for PCB board electronic-pouring characteristics: Easy mix with 1: 1 proportion Low viscosity, good flow ability Room temperature cure or heat up cure Thermal conduction, flame resistance Without solvent Using Instructions of RTV Silicone for PCB board electronic-pouring: 1. Preparing: Clean up the coating surface, remove the rust, dust, oil dirt.; 2. Pouring: Weigh the silicone and catalyst correctly, mix silicone part A and part B thoroughly, pour onto the electronic components/surface after vacuum degassing. 3. Curing: Room temperature cure or heat-up cure is both workable. 4. It should be use up after open the package, the material must be kept in a cool place sealed well, and it should avoid from contact with moisture in the air. Storage & Transportation of two parts silicone for led screen potting compound: 1. Keep it from strong sunshine, heat, and store in cool & dry place, well sealed. It has a shelf life of 12 months. 2. It can be stroked and transported as non-dangerous goods.
Application of RTV2 Footcare Liquid Silicone For Shoe Insoles Making: Footcare Liquid Silicone OTT-X705 is widely used for Silicon Insole, Silicone Gel Toe Spreaders, Silicone Gel Arch Supports, Silicone Gel Metatarsal Pad, silicon pads, Silicone Gel Heel Cups, etc. Storage and Precautions of RTV2 Footcare Liquid Silicone For Shoe Insoles Making: silicone rubber liquid is an environmentally-friendly liquid silicone product, is not easy to burn and can be stored and transported as non-hazardous goods. The shelf life of the product is about one year from the date of production. Inspection is required when exceeding the time limited. It can continue to be used in case of neither thickening nor deterioration.
1.Description of liquid silicone rubber C830 Silicone rubber is condensation cure silicone rubber for mold making. The silicone rubber will be cured under room temperature, It’s two-components, the mixing ratio is 100:2 . Part A is a flowable liquid silicone , part B is the catalyst. It has an exceptional fluidity and good operability. C-830 tin cure mold silicone has a good property , it is suitable for various mold making . 2.Characteristics of liquid silicone rubber *An exceptional fluidity and good operability, easy to demold *Good tensile strength and tear strength *lower shrinkage *non-deformation ,non-oily *good flexibility *eco-friendly *long shelf-time &lifetime 3.Application of liquid silicone rubber stone mold ,concrete mold , cement casting mold polyurethane casting mold , GRC casting mold , fiberglass cating mold statue mold , sculpture mold , resin craft mold ,artificial wooden mold gypsum mold , plaster mold ,bronze casting mold candle mold ,soap mold, shoe mold , tyre mold ,etc ..... C830 Silicone rubber is mainly suitable middle sized product and big size with simple pattern. Package: 1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum based on vacuum packing. Shelf life and transportation 1. Twelve(12) months when stored at 25C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals.
1.Description of Platinum liquid silicone rubber for mold making G830 Silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fast by heating, It’s two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible. 2.Characteristics of Platinum liquid silicone rubber for mold making *An exceptional fluidity and good operability *Good tensile strength and tear strength *Food grade silicone rubber *high temperature resistance *good flexibility *No smell ,non-toxic *long shelf-time &lifetime *Lower shrinkage 3.Application of Platinum liquid silicone rubber for mold making G830 silicone rubber is flexible silicone rubber ,it has a higher temperature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing . 4.Datesheet of Platinum liquid silicone rubber for mold making Item No. Appearance Hardness (shore A°) Viscosity (CPS) Tensile-strength( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25? ) Curing time( 25 ?) shrinkage G830 translucent 30±2 7000±1000 =55 =24 =450 1:1 20-30 mins 2~3 h =0.1% Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1. Description of food grade liquid silicone rubber for making mould Addition-curing, Food grade, Translucent, Two-component mold making silicone. 2. Characteristics of food grade liquid silicone rubber for making mould Acceptable for food contact Outstanding release properties Low viscosity Easy mixing and degassing High flowability Odorless and Nontoxic Enhanced durability 3. Application of food grade liquid silicone rubber for making mould Food Grade Related Applications Cake mold Chocolate moldmaking Candy moldmaking Baking moldmaking Ice trays molding Casting butters Casting for Kitchen products 5. Using instructions of food grade liquid silicone rubber for making mould Step 1: Prepare and clean the prototype. You must make sure your original molds perfect, fix the original mold on a board, then using some assistant material (like cardboard) to make a frame for to surround the prototype. The frame is no need, if we make the mold by brushing way. Step 2: Take the silicone and catalyst as the ratio 100:2 (silicone : catalyst= 100:2), mix the silicone rubber and catalyst evenly. Notes: rtv silicone rubber is a kind of flowing liquid and it contains two parts. Part A is a kind of flowing liquid and part B is the curing agent. Remember to mix part A and part B evenly, otherwise the silicone rubber will be partly solidified and this will bring troubles for your final operation. What's more, the finishes molds will have a short life. All of these will cause a waste of silicone rubber. Step 3: Vacuum pumping. After mixed the silicone evenly, it is better to release the bubble by vacuum pumping. Step 4: Pouring cast or brushing cast. After released the bubble, we can pour/brush the silicone rubber on the prototype. Notes: Please finishes all the steps within the operation time. If not, it will cause cross linking reaction, and no more further steps will be available. So, we have to pay attention to the pot life and curing time. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1.Description of life casting rtv-2 silicone rubber for prosthetic hands RT-810 silicone rubber is platinum cure silicone rubber with medical grade , it belong to be life casting silicone rubber. The silicone rubber will be cured under room temperature and can be cured under room temperature and can be fastly by heating. It's two components liquid silicone rubber, the mixing ratio is 1:1. It has an exceptional fluidity and good operability. Especially, the platinum cure silicone rubber has a lower shrinkage, higher temperature resistance G810 is extremely soft as a real feeling as humman skin 2.Characteristics of life casting rtv-2 silicone rubber for prosthetic hands *An exceptional fluidity and good operability *Good tensile strength and tear strength *Food grade silicone rubber *high temperature resistance *good flexibility *No smell ,non-toxic *long shelf-time &lifetime *Lower shrinkage 3.Datesheet of life casting rtv-2 silicone rubber for prosthetic hands Item No. Hardness (A°) Viscosity (CS) Tensile-strength ( kgf /cm2 ) Tear-strength (kgf /cm2 ) Elongation-break(%) Mixing ratio operation time (25 ? ) Curing time ( 25 ?) shrink-age RT-810 10 5000 40±5 10±2 450±50 1:1 20-30 mins 2~3 h =0.1% Notice of life casting silicone for prosthetic limbs RT-810 life casting silicone rubber is platinum cure silicone , which is very easy to cause cure inhibition , so please do remember thoroughly clean the model and tool before operation . Besides , please avoid the condensation silicone rubber (100:2) contact or mix with the following material , otherwise the silicone won’t be cured : 1. Liquid condensation silicone ( condensation silicone not completely cured or organic tin compounds ) 2. Sulphur, sulfide and sulfur rubber materials. 3. Amine compounds as well as contains the amine materials. 4. Pewter solder flux. Packaging & Shipping Packing: 20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing for part A + 25KG/drum vacuum packing for part B 200KG/drum packing for part A +200KG/drum packing for part B
1. Description of rtv 2 liquid silicone rubber for frame gypsum molds C830 silicone rubber is condensation cure silicone rubber (tin cure silicone rubber) for mold making. The silicone rubber will be cured under room temperature. It's two components, the mixing ratio is 100:2. Part A is a flowable liquid silicone, part B is the catalyst. It has an exceptional fluidity and good operability. 2. Characteristics of rtv 2 liquid silicone rubber for frame gypsum molds * An exceptional fluidity and good operability, easy to demold * Good tensile strength and tear strength * Suitable hardness * Copy detailed pattern * Good flexibility * Eco-friendly * Long shelf-time &lifetime 3. Application of rtv 2 liquid silicone rubber for frame gypsum mold C830 liquid silicone rubber is perfect molding material, it is suitable to make mold for concrete casting, artificial stone, brick, cement casting, gypsum decorations, plastic product, resin craft, polyester, polyurethane, bronze casting, statues, jewelry, wax, crystal, tire mold, shoe mold, clay casting, ceramic casting. etc. C830 liquid silicone rubber is mainly suitable for small or middle sized products with delicate pattern by pouring and brushing operation. Package 1kg/drum,5kgs/drum,20kgs/drum,25kgs/drum,200kgs/drum. Shelf life and transportation 1. Twelve(12) months when stored at 25C in tightly closed original packages. 2. This kind of product is non-dangerous product, which could be transported as general chemicals.
Feature of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose 1. Pure silicone rubber, anti-oil and waterproof 2. Temperature resistance from -60~260 Celsius degree 3. Anti-aging, Ozone resistance, Insulating 4. No corrosion from copper and silver and so on. Application of Transparent silicone micro tubes,silicone tube/ silicone tubing/ silicone hose 1.Environmentally friendly non-toxic, in line with the ISO/ASTM 2.High tear resistance, low shrinkage, good resistance to anti-aging performance. 3.Generally used in medical equipment, home appliances, aerospace, military, 4.Automobile manufacturing, electronic components, transformers, motors, etc...
Product Description of clear transparent silicone rubber foldable tube drinking cups for kids: 1. 100% food grade silicone material 2. Nonstick,durable, temperature resist (-40°C to 260°C), safe for dishware,microware,oven, freezer, easy to clean and remove. 3. Eco-Friendly, flexible, lightweight and portable, easy to store and transport. 4. Any colors, sizes, hardness & styles with silkscreen logo, embossed or debossed logo are available. 5. Customers' designs/samples are welcomed. 6. Reasonable direct factory price, high quality & fast delivery. Product Name: clear transparent silicone rubber foldable tube drinking cups for kids Material: Made of LFGB & FDA approved food grade silicone Color: Any color will be ok to us Working Temperature: -40~220? Size: 90*70mm Application: Tea cup
thermal conductive silicone pad is high-performance,thermal conductive gap filling materials, mainly for the transmission interface between the electronic equipment,and heat sink or product outer coving. With nice stickiness,flexibility, good compression performance and excellent heat conductivity,it make the products can discharge gas from the electronic original and heat sink, to achieve fully conforming and obviously cooling effect. 1. Grade: Food Grade insulator Silicone Rubber 2. Size: customized 3. Standard: LMS 4. Certification: ISO9001, SGS, CTI, ROHS Product Name: thermal conductive silicone pad Material: Silicone Rubber Color: Blue Size: Custom size, longth is 100m Thermal conductivity: 1.0~6.0w/mk Used: High Temperature and insulators Dielectric breakdown Voltage: >4KV Volume Receptivity:1.5*10^12O.cm Specific gravity: 2.3g/cm^2
The product is suitable for control loop, signal protection and measuring circuitry with rated voltage up to 0.6/1kv which works below 180celsius degree. It is widely used in a-energy industry, automatic control units, home appliances, coal mine, power plant and heating units etc. Feature: 1, excellent plasticity and small bend radius locations 2, good performance in heatproof and cold resistant abilities when working temperature between -60celsius and 180celsius. 3, good performance in mildew resistance, percentage of water that sop up below 0.015% 4, excellent capacity of ozone aging resistance, ultraviolet radiation aging resistance and atmosphere aging resistance 5, cable with shield is lightning-proof, electromagnetism resistant and can poise the power 6, you should connect the ends of the shield to the earth when you are installing the cable with shield. Make sure that do not break and loosen the shield, otherwise the capacity of the shield will reduce very heavily.
Cas no: 7440-02-0 Eninec no: 231-853-9 Mf: ni Grade standard:industrial, reagent Purity:20nm 99.9%. 40nm, 70nm, 100nm 99.8% Appearance: black powder Application:catalyst Size: 20nm 40nm, 70nm, 100nm Shape:spherical Note: we can supply different size products of electrode materials nickel powder according to client's requirements. Product performance Nickel nanoparticles is a high-performance electrode materials in fuel cells which can replace the precious metals platinum, thus greatly reducing the cost of the fuel cell.
Ferrosilicon is often used as a deoxidizer in steelmaking because silicon combines easily with oxygen to form silicon dioxide. Furthermore, the formation of silica releases a large amount of heat, which also helps to raise the temperature of the steel. Ferrosilicon is an alloy of iron and silicon (average content is 15% to 90%). It is a key ferroalloy used for deoxidation and alloying of steel. Silicon increases the hardness, tensile strength, elasticity and flow limits of steel, improves oxidation resistance and reduces energy losses. In steel making: Used as Deoxidizers and alloying agents In ferro alloy production: Used as reducing agent In Foundry: Used as Inoculants and spheroidizing agents Size:0-1mm, 1-3mm, 3-10mm,10-60mm, 10-100mm, lump, or customized Packing: 1MT big bag or customized
Ferrosilicon is often used as a deoxidizer in steelmaking because silicon combines easily with oxygen to form silicon dioxide. Furthermore, the formation of silica releases a large amount of heat, which also helps to raise the temperature of the steel. Ferrosilicon is an alloy of iron and silicon (average content is 15% to 90%). It is a key ferroalloy used for deoxidation and alloying of steel. Silicon increases the hardness, tensile strength, elasticity and flow limits of steel, improves oxidation resistance and reduces energy losses. In steel making: Used as Deoxidizers and alloying agents In ferro alloy production: Used as reducing agent In Foundry: Used as Inoculants and spheroidizing agents Size:0-1mm, 1-3mm, 3-10mm,10-60mm, 10-100mm, lump, or customized Packing: 1MT big bag or customized
High-purity silicon metal is used by many industries. In the chemical industry it is used for producing silicon compounds as well as silicon wafers used in photovoltaic solar cells and electronic semiconductors. And aluminum manufacturers use it to improve the already useful properties of aluminum. When used with aluminum, silicon improves its castability, hardness and strength. Besides, aluminum demand has been growing steadily in recent years, as a reflection of the economic activity in both the developed and developing word. This demand of lighter and more economical material has triggered a growth in Silicon metal consumption by aluminum manufacturers. That said, silicon compounds are the raw material for a large and growing number of industrial and consumer products such as: Silicone rubber parts Urethane foam Sealants Adhesives Lubricants Food additives Coatings Polishes and cosmetics
Silicon Metal Garde is below, please let me know if you are interested. #AluminumAlloys #Silicones #SolarPanels #SiliconMetal #441 #IndustrilSilicon Grade Si max. Fe max. Al Max. Ca max. 97 silicon 97.0% 1.5% 1.0% 0.3% Silicon Metal 553 98.5% 0.5% 0.5% 0.3% Silicon Metal 551 98.5% 0.5% 0.5% 0.1% Silicon Metal 441 99.0% 0.4% 0.4% 0.1% Silicon Metal 421 99.3% 0.4% 0.2% 0.1% Silicon Metal 3303 99.3% 0.3% 0.3% 0.03% Silicon Metal 2202 99.5% 0.2% 0.2% 0.02% Size: 10-100mm,90%min. or as per the requirement of customers Packing: 1000kg net each bag
English name: Ferro silicon Molecular formula: FeSi CAS NO.:8049-17-0 Density:6.37 Melting Point: 1360 Water solubility: insoluble in water and acid. Appearance : grey cubic crystal Storage conditions Airtight, cool, ventilated and dry place at room temperature. Application: 1.Ferro silicon is often used as deoxidizer in steel making. 2.Ferro silicon / FeSi can be used as alloy elements join agent, widely used in low alloy steel, non-ferrous metal, bearing steel, heat-resistant steels and electrician silicon-steel. 3.Ferro silicon / FeSi is used as a reductant in ferroalloy(SiMn) production and chemical industry. 4.In iron industry, ferro silicon can be used as inoculant and nodulizer.
Calcium Silicon (CaSi) Specs1: Ca: 30% min Si: 58% min Al: 1.5% max. C: 1.0% max. P: 0.04% max. S: 0.05% max. Specs2: Ca: 30% min Si: 60% min Al: 1.5% max. C: 1.0% max. P: 0.04% max. S: 0.05% max. Size: 0 - 1.6mm/0 - 2mm/10 - 50mm 90% min or the size as per customer's requirement
553 Si 98.5% min Fe: 0.5% max Al: 0.5% max Ca:0.30%max 441 Si 99% min Fe: 0.4% max Al: 0.4% max Ca:0.10%max 3303 Si 99.3% min Fe: 0.3% max Al: 0.3% max Ca:0.03%max 2202 Si 99.5% min Fe: 0.2% max Al: 0.2% max Ca:0.02%max
Silicon metal is mainly used by the chemical industry in the production of silicon compounds and by semiconductors. aluminum manufacturers to improve the useful properties of aluminum, as well as in the manufacture of silicon wafers used in photovoltaic solar cells and electronic.
