Benefits: Bearing assembly – a large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. Only four through bolts are required to hold the cartridge type housing in the frame. Liners – easily replaceable liners are bolted, not glued, to the casing for positive attachment and east of maintenance. Hard metal liners are completely interchangeable with pressure molded elastomer. Elastomer seal rings back all liner joints. Casing – Casing halves of cast or ductile iron with external reinforcing ribs provide high operating pressure capabilities and an extra measure of safety. Impeller – front and rear shrouds have pump out vanes that reduce recirculation and seal contamination. Hard metal and molded elastomer impellers are completely interchangeable. Cast in impeller threads require no inserts or nuts. High efficiency and high head designs are also available. Throatbush – wear is reduced and maintenance simplified by the use of tapered mating faces to allow positive accurate alignment during assembly and simple removal. One-piece frame – a very robust one-piece frame cradles the cartridge type bearing and shaft assembly. An external impeller adjustment mechanism is provided below the bearing housing for easy adjustment of impeller clearance. Wooden case with plastic inner packing.
Metslurry high head slurry pumps have been specifically designed to combat the need to run conventional design slurry pumps at excessive speeds to generate high heads often required in many modern slurry pumping applications. Wooden case with plastic inner packing.
The L series slurry pumps are cantilevered, horizontal, centrifugal, slurry pumps. They are suitable for delivering less abrasive, low dense slurry in the metallurgical, mining, coal and construction material industry. The shaft seal is adopted both gland seal and centrifugal seal. The L series slurry pumps have a high rate of revolution and small volume saving floor area. The frame plates have changeable, wear-resistant metal liners or rubber liners upon request and the impellers are made of wear-resistant metal or rubber. The discharge branch can be oriented to any of the eight different positions for installation and application upon request.
Pump of ZJ series Specification: D25-400mm Q12-5040m3/h H5-90m Function Introduction The products are popular among the mining, metallurgy, electric power and other industries in all places of China. The company has provided tens of thousands of matching pumps for about one hundred major projects, which include Antaipu Opencast Mine, Qinshan Nuclear Power Station, Shiheng Power Plant, Pingwei Power Plant, the Qilu 300,000 ton ethylene project, Bohai Sea oil drilling platform, Dexing Copper Mine, the second-phase construction of the Baoshan Iron and Steel Group and so on.
Type ZJ and ZJLR pumps are vertical, centrifugal slurry pumps submerged in sumps to work. They are designed for delivering abrasive, large particle and high slurries. These pumps have no need of any shaft seal and sealing water. they can also be operated normally for insufficient suction duties. Wet parts of Type ZJL pump are made of abrasion-resistant metal. All parts of type ZJLR pump immersed in liquid are lined with rubber our liners. They are suited to transport non-edge angle abrasive slurry.
Type ZJ and ZJLR pumps are vertical,centrifugal slurry pumps submerged in sumps to work.They are designed for delivering abrasive,large particle and high slurries.These pumps have no need of any shaft seal and sealing water.they can also be operated normally for insufficiend suction duties. Wet parts of Type ZJL pump are made of abrasion-resistant metal. All parts of type ZJLR pump immersed in liquid are lined with rubber our liners.They are suited to transport non-edge angle abrasive slurry. Different size wooden case
The products are popular among the mining, metallurgy, electric power and other industries in all places of china. The company has provided tens of thousands of matching pumps for about one hundred major projects, which include antaipu opencast mine, qinshan nuclear power station, shiheng power plant, pingwei power plant, the qilu 300, 000 ton ethylene project, bohai sea oil drilling platform, dexing copper mine, the second-phase construction of the baoshan iron and steel group and so o
Slurry pump Battlemountain heavy duty slurry pumps are designed for long life, efficient operation, and ease of maintenance resulting in a lower total cost of operation. Model WX,WXR,WM,WL,WG,VC,VCR......
Cantilever pumps
Slurry pumps The pump is single, single suciton, frame mounted, overhung, double casing design horizontal centrifugal pump.They are designed for severe slurry pumping: Capacities through 9000 GPM (2000 M3/HR) Heads to 350 feet (100m and 950 BHP) Temperatures to 240 degree(165 degree)
Equivalent Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps. Paper Stock Pulp Pumps and Wearing Spares working advantages: 1. High efficiency and energy saving: The operating efficiency is 3-10 percentage points higher than that of ordinary pulp pumps on average, and the energy saving and consumption reduction reach 15-30%. 2. Good cavitation performance and long service life: the actual service life can be 2-3 times longer than that of ordinary pulp pumps; 3. High concentration and no clogging: the pulp concentration can reach 6%; 4. Reasonable structure and convenient maintenance: The pump head part adopts a front and rear door-opening structure. There is no need to disassemble the pipeline during maintenance. The pump can be disassembled and repaired by simply moving the motor backward.
SP/SPR heavy duty cantilever sump pump is designed for applications requiring greater reliability and durability than conventional vertical process pumps can offer. Fully elastomer lined or hard metal fitted. No submerged bearings or packing. High capacity double suction design. Optional recessed impeller and suction agitator available. Vertical Sump Slurry Pumps Spare Parts Design features: â?¢ Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. â?¢ Impellers - Unique double suction impellers; fluid flow enters the top as well as the bottom. This design eliminates shaft seals and reduces thrust load on the bearings. â?¢ Large Particle - Large particle impellers are also available and enable passing unusually large solids. â?¢ Bearing Assembly - The maintenance friendly bearing assembly has heavy duty roller bearings, robust housings, and a massive shaft. â?¢ Casing - The metal pumps have a heavy walled abrasive resistant Cr27Mo chrome alloy casing. Rubber pumps have a molded rubber casing adhered to sturdy metal structures. â?¢ Column and Discharge Pipe - The metal pump columns and discharge pipes are steel, and the rubber columns and discharge pipes are rubber covered. â?¢ Upper Strainers - Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. â?¢ Lower Strainers - Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles.
1.5/1B-AH Slurry Pump is end-suction, split-case, centrifugal slurry pumps have set the world standard for heavy duty abrasive pumping applications. With large shaft diameters, heavy duty bearing assemblies and robust slurry pumping capacity, Application customization comes standard with this line by applying a wide variety of metallic and elastomeric parts options, an assortment of seal arrangements, and a standard impeller adjustment mechanism incorporated into every base assembly. Tobee�® AH Series Slurry Pumps are the most comprehensive range of centrifugal slurry pumps for use in mining, minerals processing, coal preparation, dredging, metallurgy, power plant, chemical and general industry applications. The wetted parts materials designed by High abrasion and corrosion resistance alloy, rubber or polyurethane etc, Expecially for handling high abrasive, high density slurries.
3/2D-HH High Head Slurry Pump is designed to produce high heads per stage at high pressures. Commonly used for long distance transport lines, the high head slurry pump lines can often satisfy application duties with a single pump where others require multiple pumps in series.
Tobee E044 Split Packing Gland Assembly is used for 6x4 EAH slurry pump, 8x6 EAH slurry pump and 10x8 EM slurry pump. Slurry Pump Gland Assembly is primarily used to compress the packing to ensure a tight seal between the packing and the bushing. Gland Assembly has a split Gland Assembly that is typically used in slurry pumps.
Tobee C090 Slurry Pump Shaft Seal is been called slurry pump shaft seal ring, Double Lip Seal as well, which is a kinds of seals spare parts of 1.5/1C-HH, 3/2C-AH Slurry Pumps, 4/3C-AH, 4/3C-SC, 75C-L Slurry pumps. Slurry Pump Intake Joint is used for sealing the pump with inlet pipeline or inlet valve for preventing leak from suction end, It is installed on slurry pump suction flange.
32056RU Impeller of 3 vanes for 3x2 C-SC series rubber lined slurry pumps, which are suited for processing the chemical acid slurries. Tobee�® Provides replacement SC and L series pump wet parts that are able to be interchangeable. Both types smaller pumps with Semi-open impellers. The material of the wet parts can be used as A05, A07, A33, A49, A51, A61, and natural rubber spares. Today we are talking about the A49 Alloy and rubber spares. They have the same function to prevent erosion and corrosion.
Spare Parts for 65QV-SP, 100RV-SP, 150SV-SP Vertical Slurry Pumps. Mainly SP Metal Lined Vertical Sump Pump Parts: Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. G refers to submerged depth 1200mm; J refers to submerged depth 1500mm; L refers to submerged depth 1800mm; M refers to submerged depth 2000mm; Q refers to submerged depth 2400mm; Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Upper Strainer - Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainer - Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
150SV-SP Vertical Slurry Pump is available in a wide range of popular sizes to suit most pumping applications. Thousands of these pumps are proving their reliability and efficiency worldwide in Minerals processing, Coal preparation, Chemical processing, Effluent handling, Sand and gravel and almost every other tank, pit or hole-in-the ground slurry handling situation.
Tobee Andritz Pump Spare Parts namely the pump parts have direct connection with slurry, are very crucial to the service life of slurry pumps. The wet parts, include impeller, liner, throatbush, frame plate liner insert, casing, etc., are very easily worn-out components because they work under longtime impact of abrassive and corrosive slurries in the high speed. For the long service life of pump parts, the material plays an important role. Tobee�® mainly manufacture Andritz Paper Pulp Pumps and Spares Parts, such as Andritz ACP, S, CP, VP, FP etc paper pulp pumps and Andritz Spares Parts. Andritz replacement parts including: Open or Semi Impellers(2 vanes, 3 vanes, 6 vanes, 8 vanes), Pump casings, Casing cover, Front linings, Rear lininings, Stuffing box body, Shaft etc, The materials can be manufactured in cast iron, SS304L, SS316L, 1.4460 Duplex stainless steel, 1.4517, 1.4517 hardened etc. ANDRITZ S & ACP Series Centrifugal Paper Pulp Pumps are available with closed, semi-open or open impellers with 3 vanes or 6vanes in a highly wear-resistant design. These pumps are suitable for conveying many different media. Depending on the impeller design, they can convey slightly contaminated and contaminated media with some solids and content up to consistencies up to 8%. S series and ACP series paper pulp pumps are wide used in the pulp and paper, mining, offshore, power, food, and chemical industry. Additionally, water supply, waste water treatment, desalination plants, and irrigation as well as drainage etc.
