Back Liner SP20041A05 is used for 200SV-SP Vertical Slurry Pump. Slurry Pump Frame Plate Liner Insert is a wear part of slurry pumps, It is also called for slurry pump back liner based on locating position in slurry pump structure, Frame plate liner insert forms a pump chamber with throat bush and volute liner where the slurry would flow through them, offers frame plate liner inserts are interchangeable with warman pump frame plate liner inserts with high chrome, natural rubber, polyurethane for different working condition.
manufacture Andritz ACP paper stock pumps and pump spares: ACP 65-315, ACP 100-500, ACP 65-250, ACP 100-315, ACP 125-400, ACP 150-500, ACP 100-250, ACP 125-315, ACP 150-400, ACP 200-500, ACP 300-700, ACP 125-250, ACP 150-315, ACP 200-400, ACP 400-700, ACP 250-315, ACP 300-400, ACP 450-550, ACP 600-700 etc. ANDRITZ ACP and S series Pump Specifications: Design:single-stage, single-flow, open and semi-open impeller Consistency:up to 8% Head:10-180 m Flow rate:up to 8,000 m3/h Pressure:up to 40 bar Temperature:up to 200 Efficiency:up to 90% ACP Centrifugal Pump Design: Impeller(230) Accelerating the medium by charging it with energy. Semi-open impeller with vanes on the back. Spiral casing (102) Guiding the medium with a favorable flow pattern, converting speed energy into pressure energy. Pressure-sealed pump casing with delivery and suction channels. Suction and delivery flange. Holds the bearing housing with bearing assembly, shaft and impeller. Pump shaft (211) Holding the impeller, shaft seal, bearing assembly and coupling. Transmitting the drive energy to the impeller and thus, to the medium. Sturdily dimensioned drive shaft. Bearings Interface between stationary and rotating parts. Absorption of axial and radial forces. Impeller side: Two angular contact ball bearings (321.1) with steel cage. Drive side: One deep groove ball bearings (321.2) with steel cage. Shaft seal Depending on operating requirements, there is a choice of eight different shaft seals: Cartridge mechanical seal - single Cartridge mechanical seal - double Standard cartridge mechanical seal - single Standard cartridge mechanical seal double Single standard mechanical seal Tandem mechanical seal Stuffing box packing Dynamic shaft seal
Slurry Pumps, Warman Pumps, Pump Parts, Pump Casting And Cyclone.
Slurry pumps, spare parts, valves, motor.Manufacturer
Water drilling rig, truck mounted drilling rig, mud pump, turntable drilling rig, truck mounted crane.Trasportation, clearing agent, shipping
Warman type slurry pumps, heavy duty slurry pumps, slurry pump parts, rubber lined slurry pumps, dredging pumps, sand and gravel pumps, vertical slurry pumps.
Impeller for 8AHF Pump
pump impellers are interchangeable with AH/HH/LM pump impellers, The Impeller is one of the most important parts for slurry pump. Centrifugal slurry pumps need impeller to produce the centrifugal force which transfer the . The centrifugal force is produced by the impeller which rotates to a certain speed, As main rotating component which normally has vanes to impart the centrifugal force to the liquid, Usually, slurry pump impellers have a plain or a Francis type vane.
Description 11 inch Impeller 19121-70-30 is used for 6x5x11 Mission Magnum Centrifugal Sand Pumps. provides 19121-xx-30 impellers for Mission Magnum centrifugal pump 6x5x14: 19121-70-30 Impeller 6 x 5 11 inch 19121-80-30 Impeller 6 x 5 12 inch 19121-90-30 Impeller 6 x 5 13 inch 19121-A0-30 Impeller 6 x 5 14 inch Fully open impeller, best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease. Allows for simple restoration of clearances when wear takes place. Back pump-out vanes reduce pressure on the shaft seal, reduce axial thrust on the bearings. Part size cast into the impeller. This makes part identification easier. Impeller gasket in included with impeller All impellers are dynamically balanced Offered Hard iron and other materials upon request
Description 19122-01-30A Casing is an important Wear Parts for Mission Magnum 6x5x11 Centrifugal Pump. All of the pumps feature a concentric casing. This casing averages 37% thicker than conventional pump casings, and up to 50% thicker for the larger, mud pumping models. They are pressure rated at 1 .5 times the flange rating and are designed with a 1 /8 erosion allowance. The concentric style casing has proven to offer the greatest pump life and reduced downtime. The walls of a concentric style casing are an equal distance from the impeller throughout the impeller circumference, which results in a smooth flow pattern. A volute style casing has a cutwater point that disturbs the fluid flow pattern creating an eddy. The concentric casing eliminates vibration, turbulence and aeration that is caused by the cutwater point in conventional volute pumps. It also reduces the high bearing loads and shaft deflection even at near shutoff flows. The Mission I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The revolutionary design of the I provides supreme-duty performance in all types of fluid pumping operations. Although it offers greater capacity and higher heads, the I remains the competitive pump of choice for aggressive applications. The I is more powerful, more durable, and easier to maintain than any conventional pump in use today. The has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The is available in , hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration). Also available, Horizontal and Vertical Close Coupled Magnum.
OEM Andritz ACP series pump spares Impeller ACP 150-400.5 semi-open type in a highly wear-resistant design.
FP40-400.12 Fan Pump Exchange Unit / FP40-400.12 Rotor Unit is 100% interchangeable with original Andritz FP40-400.12 Fan Pump, Th FP40-400.12 Exchange Unit made from duplex stainless steel 1.4460. FP Series Fan Pump is a low pulse and high efficient paper pulp pump, It is new standards in terms of efficiency, flexibility, and design. This double-suction pump series was designed for flow rates up to 20,000 mh and heads up to 220 m. The pumps can convey stock suspensions with consistencies of up to 2%. The fan pump supplied has a very high efficiency of 92% and lowest pulsation in order to guarantee perfect sheet formation. High efficiency and low pulsation Water With efficiencies of over 90%, FP40-400.12 Double Suction Split Case Pumps permanently help to save valuable energy.
Slurry Pump, Warman Pump Parts, Oem Pump.
Pumps, slurry pumps, valves, mining equipment.Technical services, transportation
Pump, pump parts.
manufactures Andritz alternative ACP, S, VP, FP, CP series Paper & Pulp Stock Pumps and Pumps Wearing Spares, all the pumps and spares parts are widely for Paper mills, Paper Pulp, Coal prep, Waste pulp, Paper stock, Paper making, Waste paper stock, Chemical slurries, Sugar refining, Recycled fiber preparation, Chemical industry, Food industry, Energy supply, Water supply, Waste water treatment, Alkali recovery, Sugar syrup, Molasses, Pharmaceuticals industry, Potash Fertilizer Plant, Other industries etc. Andritz S pump spare parts including: Impeller (2 vanes, 3 vanes, 6 vanes, 8 vanes), Volute Casing, Casing Cover, Front Lining, Rear Lining, Stuffing Box Body, Shaft Wear Sleeve etc which for Andritz S series paper-pulp pumps.
Design Features: Impellers - wide variety of metallurgic and elastomeric options (metal and elastomer interchangeable) pump out vanes on rear and front (on closed impellers) reduce recirculation within pump, and aid in preventing seal contamination optional castings of straight or semi-Francis vanes (from 3 to 8 vanes on certain sizes) offer wider hydraulic options in single sizes. Liners - wide variety of metallic and elastomeric options (metal and elastomer liners are interchangeable) to select from in order to provide the longest wear life possible. Bearing assembly - Cartridge-style bearing housing allows for removal from pump and assembly in controlled environment, Oversized shaft diameters and reduced overhang in the wet-end contribute to long life and reliability in the field. Seal arrangements - Expeller (Centrifugal Seal): no external sealing water required where applicable. Stuffing Box: flushed gland sealing with braided packing and a lantern ring. Mechanical Seals: advanced sealing technique without sealing leakage.
20943-21 641102182 Sleeve, Shaft used for Mechanical Seal Mission Magnum Centrifugal Pump. The Mission I has been engineered for the toughest jobs in drilling, production, well-servicing, and industrial applications. The revolutionary design of the I provides supreme-duty performance in all types of fluid pumping operations. Although it offers greater capacity and higher heads, the MAGNUM I remains the competitive pump of choice for aggressive applications. The I is more powerful, more durable, and easier to maintain than any conventional pump in use today. The has an open impeller design that contains wide-tipped vanes and a more tangential circumference of the suction allowing the pump to create a smoother flow pattern when handling abrasive fluids. The is available in Magnachrome, hard iron, stainless steel, and aluminum bronze fluid ends. The pumps can be unitized with electric motors, diesel engines, and hydraulic motors (horizontal, vertical, or close-coupled configuration). Typical Applications
Description P/N: 20612-02-33 (646490557) Shaft for Mission Magnum Centrifugal Pumps and 2500 Supreme Pumps. offers a complete line of centrifugal sand pumps to suit for all kinds of drilling sand pump application. Size ranges from 3x2x13, 4x3x13, 5x4x14, 6x5x11,6x5x14, 8x6x11,8x6x14, 10x8x14, 12x10x23 to 14x12x22b. Bare pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal magnum pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to mud pump as a filling pump. 6511 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump.
Description P/N: 20612-02-33 (646490557) Shaft for Mission Magnum Centrifugal Pumps and 2500 Supreme Pumps. offers a complete line of centrifugal sand pumps to suit for all kinds of drilling sand pump application. Size ranges from 3x2x13, 4x3x13, 5x4x14, 6x5x11,6x5x14, 8x6x11,8x6x14, 10x8x14, 12x10x23 to 14x12x22b. Bare pumps, matching motors are available from 7.5KW to 90KW, with rotation 800, 1000, 1150,1450, 1750 to 3500 RPM at 50Hz or 60Hz. The model 10x8x14 and 8x6x14 centrifugal magnum pump used on solid control system over 3000 meter-long drilling rigs, with big viscosity and heavy specific gravity drilling fluid. 8x6x11 centrifugal mud solid control feeding pump applies to under 3000 meter-long drilling rigs, and it also can be used to supply mud to mud pump as a filling pump. 6511 centrifugal pump applies to truck-mounted drilling rigs or pocket drilling rigs. 4x3x13 drilling centrifugal pump is usually used as measuring pump or replenishment pump. 3x2x13 model pump is usually used as clean water pump.
