Reflow/wave soldering machine reflow: Dependable and steady conveying system and effective device. 1. Unique transportation lead rail design, adopts good quality aluminum alloy. The intensity is high, the distortion is small, the precision the high, the parallel degree isf+0.5mm 2. Automatic adding oil system controlled by computer. Adding oil automatically. Adding oil to lubricate conveying chains and central support chains during normal operating time every a period of time. 3. Delayed time output when the power is off. When the city power is not provided with, conveying chains may output continuously PCB board inside the stove, prevent the PCB board from burning. Special nitrogen/rosin recycling cooling filtering system 1. Recycle the weld wasted air forcibly with seal. Recycle and reuse the nitrogen through special big capacity cooling filter system. 2. Huge capacity rosin filter, full seal, keep nitrogen density, no man cleaning. High efficiency nitrogen flux control system 1. Adopt Japanese control valve control nitrogen flux, according to welding density requirement scope to adjust automatically nitrogen flux in the welding section. Reduce nitrogen consumption. Let nitrogen in and let oxygen out quickly, oxygen content in the stove decrease to ppm in 10 minutes. Systematic function 1. Conveyor Speed, Hot wind speed, controlled by the computer. 2. Built-in UPS and power off protection function 3. Various over loading will stop the correspond epuiqment.Built-in UPS and power off protection function 4. Turn off all epuiqment when Emerency Stop is pressed. 5. Conveyor speed close-loop ontvolled accurately 6. Built-in over-temp Alarm function, and display on the screen. 7. Operate "turn off" "delay turn-off" "Reset" "Parameter setting" "profile testing" by the computer. 8. With temp- profile analysis function and saved as Data or Graph files. 9. PID self-tuning control, With f+1fªC accuracy. 10. PID output time-sharing to reduce down the MAX Power. 11. Product amounts counts and display on the screen. 12. With fast sampling rate for 10pcs/sec, thermal-open alarm function. 13. With embedded-in real-time control, system function runs inde pendently, not depending on PC. 14. Board I/O, A/D, power is isolated for EMC Design. 15. PCB current staus for real-time display In the pot. 16. With MYSQL NET data management, easy for ERP/MRPII system integration. 17. SSR failure sensing function, and turn off the system power to prevent from accident. High efficiency advanced carrying wind and heating system 1. Carry the wind independently in each temperature zone. Adopt closed ring PID to control. The temperature control is accurate. The control precision is high. 2. Unique carrying wind mode, the wind force is even, which covers every corner of the stove, the temperature is even, the heat efficiency is high. 3. Carrying wind recycles independently in the temperature section. Heat independently up and down. The firepot temperature is accurate and even. The heat capacity is huge and easy to adjust. 4. Over temperature warp alarm. Over oxygen content and falling down board alarm, malfunction diagnosis, sound & light alarm. 5. The starting power is small, the temperature increases quickly, Temperature increasing time from room temperature to working temperature s less than 20 minutes. 6. Normal use consumption power is small, temperature steady consumption power is 8 KW. 7. Adopt imported electromotion actuator to hoist on the top cover of the furnace body. Safe bar supports and the safety is dependable. 8. Good quality and bearing high temperature motor carry wind. The carrying wind speed is steady, the noise is small, the vibration is small. Features 1. Windows 2000 operation system, the dependability is high, the operation speed is quick, the communication is steady, the management is convenient and may connect with LAN. 2. Chain ,central support and web belt are in-phase which prevent PCB from distorted when heated or the board falling down. 3. Good quality nitrogen protect device, adopt Japanese control valve to control flux, save nitrogen consumption 30%. 4. Cooling temperature control, control effectively cooling decrease. 5. Conveying chains drop oil automatically to lubricate. 6. Alarm record and motion incident record may store, inquiry and trace back conveniently. The longest time to store is one year. 7. Special soldering recycle system make sure soldering quality and keep clean. 8. Heat recycle efficiency is high, starting power is Iow, increase the temperature quickly, the increasing temperature time is less than 20 minutes, the use power is small, thenormal power is only 8 KW. 9. Carrying wind adjust speed without grade, may adjust at random according to PCB board and components feature, which make the best soldering effect. 10. Use big capacity UPS, which keep conveying and micro-computer output when the power is off. 11. Enact at random to open the machine, close the machine time automatically. Full automation and half automation switch, realize the automation without man operation. 12. Each temperature zone control the temperature independently. Adopt the closed ring PID control mode, control precision is high. Mode CY-821(N) Figure size L4800 f+W1345f+A1437 Weight 1700kg Power supply 3PH AC380V 50 / 60HZ Starting power/starting power 40KW / 8KW PCB biggest width 450mm Conveyor effective height f+30mm Conveyor speed 0~1800mm / min Adjust width mode adjust the width with electromotion Chains lubrication drop oil automatically Conveyor direction left-right (right-left), may choose Conveyor mode chains+web belt or chains+central support Furnace body open and closed mode Hoisting with self-lock and electromotion Temperature control section 18 Temperature control scope Cnormal temperature-300fª Temperature control mode closed ring control Temperature collect precision 0.1fªC Temperature collect precision f+1fªC PCB horizontal warp f+2fªC Cooling mode cooling wind recycles to be cooled Carrying wind speed control 0~2800r/min adjust the speed without grade Abnormal alarm Flame couple is abnormal, overemperaturre, fallinging down board, over oxygen content in nitrogen. Parameter store store many parameters Incident record store for one year Temperature increasing time f-20min Nitrogen consumption 20m3 / h Protection when the power is off Delaying time for output Operation system Windows2000 Temperature curve test Produced related parameter automatically wave: Features 1. Lead-free process, environment protection design. 2. Adopts irregular internal furnace and open streamlining appearance. 3. Specially made aluminum alloy sideway, with high strength and high hardness. 4. Automatic synchorous plate connecting device, stable and smooth plate connection. 5. Superior titanium claw type chain, with high elasticity, no easy of distortion, corrsion resistant. 6. Closed constant pressure flux spray system, ensures the stability of spray pressure. Flux automatic follow-up system: continuous reciprocal type spray is adopted, spray area, time are automatically regulated with the width of PCB board and speed change. 8. Equipped with double-layer waste gas filter board for rosin, effectively reduce pollution 9. Preheating device: powerful hot wind system, sent hot wind evenly to the bottom of PCB board. Direct draw-out modular design is adopted, convenient for cleaning. 10.Preheat compensation function, temperature drop by f-2fªC before PCB board enter tin oven. 11. Spray current wave crest: spiral spray design, weld the shaded part of SMT components perfectly. 12. Precise current wave crest: advanced plane current technology, very little tin oxide, the laminar flow wave makes tin point Approach perfection. 13. Double waves of tin oven adopt stepless frequency change, control height of wave crest independently. 14. Automatic claw cleaning device: inported superior micro-water pump, detergent is propylene, clean chain claw automatically. 15.Chilling system: cold wind is -10fªC, PCB temperature fall, with cold wind for -8fªC/sec, without cold wind -3fªC/sec. 16. Economical running: tin wave lift up and go down with PCB board, daily tin oxide can reduce max 30%. 17. Automatic darm function of dramatic temperature change, PCB board tracks and counts automatically. 18. The machine above , following is controlled , There are certain stabilities
Cheap price selective jet wave soldering machine with CE Features 1.Welding: Manual jet wave soldering machine ismost suitable for the small batch PCBA DIP welding the parts of a PCBA (SMD+DIP chips mixed). 2.Repair: Manual jet wave soldering machine ismost suitable for the repair the PCBA, it can tear down the chips on to the PCBA. Specifications Model MAX-S310A Dimensons 465X447X410mm Solder tank size 296x100x100mm Solder capacity 23KG Nozzle size 130*60mm Power source 1P 220V/50Hz-60Hz Power 2.5KW Control method By foot switch or by manual. Frequency converter stepless control. Start wave delay 0-30s Heating time About 1H Temp control method PID+SSR Temp precise ±3 Weight Approx.40KGS Our services 1.your inquiry about our products and price will be replied within 24 hours. 2.Best products and price to offer. 3. shortest time to delivery the products. 4.OEM&ODM service offered. 5.With 1 year warranty. 6.Good packing.
Features: 1.Control system: Applies to the PLC + touch screen controller, Ensure system reliability and stability 2.Conveyor system: Guide rail is with special design,hard out of shape;Width can adjust,accurate and smooth.Titanium alloy conveyor finger,strengthen and wear resistance, 3.Spray system: SMC cylinder +Japan ST-06 spray nozzle.Spray speed,stroke can adjust.Spray is uniformity.Flux collection system are optional. 4.Preheat system: Modular design,high precise temp control. 5.Welding system: Patent solder tank design,Lead free solder tank,longer lifespan.Solder temperature control accuracy. 6.Cooling system: Forced air cooling+cooling fan Product Name Lowest Price Mini Wave Soldering Equipment SMT PCB Soldering Machine For Sale Power for heating up 12KW Control system PLC + touch screen Dimensions 2600*1200*1600mm PCB size 0-250mm PCB conveyor height 760±20mm PCB conveyor speed 0-2.0m/min Preheating zone length 800mm(two section) Preheating zone qty 1 Preheating temperature Room temp-250 Solder capacity 180Kgs Solder temperature Room Tempï½?350â?? Temperature control method Touch screen+ PID Flux storage tank Max5.2L Power 3P 5W 380V Power for heating up 12KW Wave Dual wave Air source 4-7kg/cm2 12.5L/min Weight Approx.400Kgs
Brief Introduction : Shenzhen XHL Industrial Development Co., Ltd is professional in researching and manufacturing high quality glue dispenser machine , glue potting machine ,glue mixing machine ,LED silicon Strip extrusion machine , automatic Robert screw locking machine and automatic soldering machine etc automatic equipment. The products are using for LED , Widely used in arts and crafts (stickers, patches, trademark paper, cartoon paper, label, photo album), digital electronics, LED waterproof power supply, smart card signage, IC card, trademark, logo label (circuit board, PCB), clothing accessories and so on . Our glue machine can Suitable for all kinds of two-component glue, such as double-liquid glue, AB glue, silica gel, epoxy resin, PU glue . All of our machine can be acceptable customized with your required size and function. Service : Free testing , One year Warrantee ,and lifetime Service . Our machines can use for assembly production line .Welcome to ask for inquiry . Hope to cooperate with you sincerely . Quick Details Place of Origin:Guangdong, China (Mainland) Brand Name:Xhl Condition:New Work Area:400(x)*400(y)*100(z)mm XYZ Repeatability:±0.03mm Certificate:ISO9001 After-sales Service Provided:Field installation, commissioning and training, Video technical support, Online support, Overseas third-party support available Supply Ability 500sets/per month Packaging & Delivery Strong wooden cases suitable for a long distance shipment. package weight :about 50kg package size: about 700(L)*700(W)*950(H) mm Port:Shenzhen Lead Time:
Brief Introduction : Shenzhen XHL Industrial Development Co., Ltd is professional in researching and manufacturing high quality glue dispenser machine , glue potting machine ,glue mixing machine ,LED silicon Strip extrusion machine , automatic Robert screw locking machine and automatic soldering machine etc automatic equipment. The products are using for LED , Widely used in arts and crafts (stickers, patches, trademark paper, cartoon paper, label, photo album), digital electronics, LED waterproof power supply, smart card signage, IC card, trademark, logo label (circuit board, PCB), clothing accessories and so on . Our glue machine can Suitable for all kinds of two-component glue, such as double-liquid glue, AB glue, silica gel, epoxy resin, PU glue . All of our machine can be acceptable customized with your required size and function. Service : Free testing , One year Warrantee ,and lifetime Service . Our machines can use for assembly production line .Welcome to ask for inquiry . Hope to cooperate with you sincerely . Overview Quick Details Place of Origin:Guangdong, China (Mainland) Brand Name:XHL Technology Condition:New Work Area:800(x)*300(y1)*300(y2)*100(z)mm R-axis:360° XYZ Repeatability:±0.03mm Certificate:ISO9001 After-sales Service Provided:Field installation, commissioning and training, Video technical support, Online support, Overseas third-party support available Supply Ability 300sets/per month Packaging & Delivery Strong wooden cases suitable for a long distance shipment. package weight :about 85kg package size: about 1100(L)*750(W)*900(H) mm Port:Shenzhen Lead Time:
HRM-640/840 Lead Free Reflow Oven Features Streamline shape design make the oven looks great. Touch screen and PLC controlling system .It can save 50 groups temperature parameters and provide extra 2 ports for profile testing. The software has the functions like , temperature setting and editing, PCB parameter menu, and profile testing, alarms and multi-languages conversion. Brand electrical component like Schneider (German) breaker, KETE(Korea) SSR, Omron (Japan) box breaker. Meanwhile the CE certificated blower is specially design for lead-free reflow oven. It runs stable and lower noise. Upper zone and hood can be opened by the electrical screw automatically. It is very convenient for cleaning and maintenance.Electrical pole will hold the upper zone and cover, even when power is off suddently, the cover will not drop down. It's much safer than the air cylinder holder. Specially designed Ni-Cr heater filaments, provide a very quick ramp up time. It takes just 15 minutes from ambient to setting temperature. The inner tunnel of the oven is made of stainless steel which easy for cleans. The entire upper and bottom zones are forced air convection; provide great temperature accuracy and uniform. Stainless steel mesh belt and pin chain conveyor work together. Industrial chiller provides better cooling performance.
Features: 1.Use Windows operation interface, easy to operate; 2.Leading heating mode, solve the corner when the reflow soldering welding problem, suitable for CSP, BGA, 0201 chip, and other electrical components of the welding; 3.Professional rotor design, wind speed stability, effectively prevent the PCB heating uniformity of the wind, to the repeated heating of the highest; 4.Compulsory independent loop to various temperature zones, independent PID control, and independent heating mode, make the furnace chamber temperature accurately, even, heat capacity is big. 5.Thermal insulation layer is made of high quality aluminum silicate insulation materials, heat preservation effect is good, warming faster, from room temperature to the working temperature of 15 minutes. 6.Furnace, lead-free green design; 7.High quality high temperature and high speed motor transport wind smoothly, little vibration, low noise; 8.Furnace using cylinder jack-up, safety rod support, safe and convenient; 9.The transmission way of PCB machine adopts automatic electronic speed, chain network ,synchronization, good stability; 10.Special high quality aluminum alloy guide, automatic refueling system, ensure guide rail adjusted the service life of the high precision and wide; 11.Equipped with UPS power protection function, ensure the normal output after power PCB, avoid damage; 12.Powerful software function, the PCB online temperature measurement, and analyze the data curve at any time, storing and printing; 13.PC and PLC communication with PC/PP agreement, stable work, put an end to crash; 14.Automatic monitoring and display equipment working state; 15.Special furnace design, good heat preservation, adopt special heating element, heat with highefficiency, power consumption of the lowest.
Features: 1.Use Windows operation interface, easy to operate; 2.Leading heating mode, solve the corner when the reflow soldering welding problem, suitable for CSP, BGA, 0201 chip, and other electrical components of the welding; 3.Professional rotor design, wind speed stability, effectively prevent the PCB heating uniformity of the wind, to the repeated heating of the highest; 4.Compulsory independent loop to various temperature zones, independent PID control, and independent heating mode, make the furnace chamber temperature accurately, even, heat capacity is big. 5.Thermal insulation layer is made of high quality aluminum silicate insulation materials, heat preservation effect is good, warming faster, from room temperature to the working temperature of 15 minutes. 6.Furnace, lead-free green design; 7.High quality high temperature and high speed motor transport wind smoothly, little vibration, low noise; 8.Furnace using cylinder jack-up, safety rod support, safe and convenient; 9.The transmission way of PCB machine adopts automatic electronic speed, chain network ,synchronization, good stability; 10.Special high quality aluminum alloy guide, automatic refueling system, ensure guide rail adjusted the service life of the high precision and wide; 11.Equipped with UPS power protection function, ensure the normal output after power PCB, avoid damage; 12.Powerful software function, the PCB online temperature measurement, and analyze the data curve at any time, storing and printing; 13.PC and PLC communication with PC/PP agreement, stable work, put an end to crash; 14.Automatic monitoring and display equipment working state; 15.Special furnace design, good heat preservation, adopt special heating element, heat with highefficiency, power consumption of the lowest. If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
HR-350 LFC Lead Free Wave Solder Machine Features: 1.Shape streamlined design,interior modular design suitable for SMT and DIP components lead-free soldering; 2.Full PC+PLC control system,windows operating system interface in English online arbitrary switching; 3.Nozzle stepper motor drive,to ensure uniform coating of flux; 4.Forced natural air cooling system,optional external chiller rapid cooling; 5.Special furnace vents design,welding,small amount of dross. 6.Can be automatically turned on and off according to theusers set time. If you want more information ,feel free to contact us .Email :monica@szhonreal.com ,
Features: 1.Use Windows operation interface, easy to operate; 2.Leading heating mode, solve the corner when the reflow soldering welding problem, suitable for CSP, BGA, 0201 chip, and other electrical components of the welding; 3.Professional rotor design, wind speed stability, effectively prevent the PCB heating uniformity of the wind, to the repeated heating of the highest; 4.Compulsory independent loop to various temperature zones, independent PID control, and independent heating mode, make the furnace chamber temperature accurately, even, heat capacity is big. 5.Thermal insulation layer is made of high quality aluminum silicate insulation materials, heat preservation effect is good, warming faster, from room temperature to the working temperature of 15 minutes. 6.Furnace, lead-free green design; 7.High quality high temperature and high speed motor transport wind smoothly, little vibration, low noise; 8.Furnace using cylinder jack-up, safety rod support, safe and convenient; 9.The transmission way of PCB machine adopts automatic electronic speed, chain network ,synchronization, good stability; 10.Special high quality aluminum alloy guide, automatic refueling system, ensure guide rail adjusted the service life of the high precision and wide; 11.Equipped with UPS power protection function, ensure the normal output after power PCB, avoid damage; 12.Powerful software function, the PCB online temperature measurement, and analyze the data curve at any time, storing and printing; 13.PC and PLC communication with PC/PP agreement, stable work, put an end to crash; 14.Automatic monitoring and display equipment working state; 15.Special furnace design, good heat preservation, adopt special heating element, heat with highefficiency, power consumption of the lowest.
Our products are widely used for laser marking, laser welding and laser cutting in various industries. Kinds of laser series meet different processing requirements. Features 1. High accuracy,CCD monitoring and positioning guarantees soldering yield rate. 2. Automation, open interface design makes customized automation available. 3. High Stability, temperature negative feedback control mode guarantees welded product consistency. 4. Suitable for soldering precision electronic components, like coaxial cable and terminal, USB traverse, mobile phone antenna and camera, high frequency transmission line, etc.
Features 1. Widely applicable, extensively applied in precise welding of various metals and non-metals 2. High flexibility, deployed with a manipulator, it can realize a precise welding in different angles 3. High stability, adopting energy negative feedback technology to ensure laser power output is stable. 4. Laser power output is verified and maintained to ensure high welding repeatability and quality.The output power is shifted within ±2%. 5. During processing, waveform can be adjusted according to shape and material of workpiece to improve welding quality greatly. 6. Energy and time share options enhance processing flexibility. Maximum 4 beam delivery optical fibers can be equipped. It can support more than one workstation or multiple welding heads to improve production efficiency. 7. It can communicate with other system through I/O connectors. Imported major components with high quality ensure system reliability. 8. Welding parameter can be saved in Chinese and English name.Storage capacity can be extended. User-friendly interface.
TETE laser equipments are widely used for laser marking, laser welding and laser cutting in various industries. Kinds of laser series meet different processing requirements. Features 1. Widely applicable, extensively applied in precise welding of various metals and non-metals 2. High flexibility, deployed with a manipulator, it can realize a precise welding in different angles 3. High stability, adopting energy negative feedback technology to ensure laser power output is stable. 4. Laser power output is verified and maintained to ensure high welding repeatability and quality.The output power is shifted within ±2%. 5. During processing, waveform can be adjusted according to shape and material of workpiece to improve welding quality greatly. 6. Energy and time share options enhance processing flexibility. Maximum 4 beam delivery optical fibers can be equipped. It can support more than one workstation or multiple welding heads to improve production efficiency. 7. It can communicate with other system through I/O connectors. Imported major components with high quality ensure system reliability. 8. Welding parameter can be saved in Chinese and English name.Storage capacity can be extended. User-friendly interface.
Features 1. Flexible and convenient for processing, easy for system integration 2. Energy negative feedback technology is employed to improve the repeatability of the energy transmitted by the laser 3. Waveform can be adjusted according to shape and material of workpiece. 4. The light beam can be split based on energy or time to realize simultaneous or sequential welding. 5. It can communicate with other system through I/O connectors.
Hot air soldering other welding soldering supplies for welding SMT line PCB solder paste from China Features: 1.Windows 7 operation system,Chinese-English interface ,easy to operate. 2.All production data can be backup automatically,which is convenient for the ISO 9000 management. 3.Enjoy the intelligent diagnosis function,it can display ,alarm the trouble and store them. 4.There is special brush in the finger box, it can clean the finger totally. 5.Cross-flow fan design ,which can make the twice forced air cooling. 6.High power forced air cooling system, make the PCB cooling speedy. 7.Built -in rectfier system,uniform wind speed, uniform cooling. 8.Module transportation system,the entire tooth box type structure,which makes the transmission smooth. 9.Reinforced titanium finger, hard to out of shape. 10.Both of two waves width can be adjustable,minimize the oxidation of the tin oven. 11.Backflow slot design,which can gathered the tin slag automatically to one side of the oven. 12.Standard full titanium soldering pot more suitable for the lead free production. 13.1/2HP high power motor,meet the wave length up to 15mm. 14.PLC+PID closed loop control,more stable and higher repeativity precision. Packing & Delivery Packing Details : plywood case, for export! Port:shenzhen Delivery Details : 5-7days Our Service Respond in time. Your inquiry about our products and price will be replied within 24 hours Cheap and fine We provide you with high quality materials and competitive prices Good communication Well-trained and experienced staffs to answer your enquires in fluent English High efficiency. Complete the production shipment in the shortest time High quality Strict QC before shipping the products,Responsible for the quality of all products
Gs-301 jewelry welder machine/spot welder/welding ring machine Feature: Particularly welding the variety of pure gold, 22k, Pt (platinum) and silver, is also can welding. Welding chain(different shapes of closed small circle) Parameter: Suitable for welding 0.3-0.5mm diameter pt wire, 0.3-0.6mm diameter 24k and silver. Power supper: Ac220v(200-240v), Ac100-120v(to be ordered) Net weight:5kg Total weight:7kg
Brzda-brake-frein-bremse Siemens brake 2lm8002-1, 2lm8005-2, 2lm8010-3, 2lm8020-4, 2lm8040-5, 2lm8060-6, 2lm8100-7, 2lm8230-8, 2lm8300-0, 2lm8315-0, 2lm8400-0,
Our optical fiber patch cord is high return loss and low insertion loss , insertion loss of patch cord is less than 0.2db, return loss of patch cord is upc more than 55db , apc is more than 60db Applications 1. Catv 2. Active dvice termination 3. Telecommunication networks 4. Metro 5. Local area networks(lans) 6. Data processing networks 7. Test equipment 8. Premise installations. 9. Wide area networks(wans) Polish:pc/upc/apc Operating temperature range: -40 --80 Storage temperature range: -40 --80 Tensile strength: >10kg Fiber cable diameter: 0.9mm, 2.0mm, 3.0mm fiber is available Fiber jacket pvc or lszh cable is available Fiber optic patch cord with excellent changeability and repeatability Carton
AWithZ MC1 DIY Portable Spot-Welding Machine Micro Spot Welder with 7500mAh Built-In Rechargeable Battery /Power Bank Function for iPhone, Android Phone Battery Flex Repair Tool. Features: High quality material: This lightweight, portable spot welder Efficient welding: It is a total of 611 gears of output power, easily adjustable, for precise welding; and there are LED lights to indicate the working gear. Good performance: Welding pen, with gold-plate terminal, long enough, flexible to use, quick to install, fine conductivity, ensures beautiful welding spots. Safe, Reliable Use: The welding machine has low voltage, over current and over-charge protection, low battery alarm function, auto-off under low power. Power Bank Function: Built-in rechargeable battery, 4000mAh high capacity, supports it to fast charge the mobile devices via 5V 2.4A USB port, very convenient. Specification: Material: Aluminum alloy Output current: 650A (Max) Capacity: 4000mAh Input current: 5V/2.1A(Max) Input interface: Type-C port Host size: 165*90*30 Host net weight: 272g Packing size: 200*110*65mm Battery: Rechargeable polymer lithium battery Packing List: 1 * Spot Welder 1 * Welding Pen 1 * Type-C Charge Cable 1 * Nickel Sheet 2 * Magnet Pushpin
i2C T-12 Plus 240W dual-handles soldering station for Mobile Phone welding repair. i2C T12-Plus Dual-Station precision soldering station for electronic applications with 2 handles. i2C T-12 Plus 240W portable adjustable temperature soldering station with double handles base and Iron tips for PCB CPU IC soldering repair. Features: 1. With Dual welding handles, and it can work at the same time, no need to switch back and forth, automatic sleep mode. 2. It heats up in 1 second and reaches 500â?? in 2 seconds. 3. 2 seconds heating up, 5 seconds tinning, 240w high power, 110V/220V AC power supply. 4. 24V/ 10A High power transformer. 5. High temperature resistance, corrosion resistance, compact body, strong durability. 6. Quickly improve your work efficiency: prolong the service life of the iron head. 7. All metal soldering frame: T12 special soldering frame. 8. Zinc alloy material, the handle is not easy to slide after insertion, longtime does not work. Can enter the sleep mode, improve the service life of the iron head, with a clear Wash sponge, and easily clean the stolen goods on the iron head. 9. T12 Plus host Aviation: grade aluminum alloy material.
