AIGI 350G Steamed Aramid Fiber Sheets AIGI 350G consists of special steamed aramid fibers and stretch binders. They make excellent gaskets, especially in steam applications. AIGI 36 Virgin PTFE Sheets Features & Benefits Excellent corrosion resistance Widely used in most applications Ideal choice for replacing asbestos material AIGI 126 Glass Fiber Reinforced PTFE Sheets Features & Benefits Avoids creep relaxation and emission Improved chemical resistance Improved hardness Excellent deformation resistance AIGI 141 NBR Sheets AIGI 141, Nitrile Rubber has outstanding heat resistance which makes it can be used under 120°C atmosphere for a long time. Meanwhile, AIGI 141 has a high gas-tightness ability too. While NBR is not suitable under low temperature and it gets a low dielectric property. AIGI 141 NBR sheets are used under Alpha Olefin Lube; Ethylene glycol; hydrocarbon fuel; Silicon oil; Grease; water; water-based engine cooling liquid; etc.. AIGI 142 FR Sheets AIGI 142, Fluorubber could work under high temperature, oxidize and most of liquid, also with an excellent physical-mechanical properties; which makes AIGI 142 be used in a wide range of industrial applications, like alcohols lube; petroleum liquid; Sulphosuccinic acid ester liquid; etc.. AIGI 144 Neoprene Sheets AIGI 144 Neoprene sheet has outstanding weatherability, excellent resistance to oil and ozone; and excellent adhesiveness which makes it one of the best gasket materials in the sealing industry. AIGI 144 could be widely used in silicon oil; grease; low temp. water and water-soluble; refrigerants; ammonia water; CO2; ozone; etc.. AIGI 146 EPDM Sheets AIGI 146 EPDM could withstand low temperature, and has good resistance to light aging and alkali. It has excellent electrical insulation ability. AIGI 146 could be used in alcohol; dilute acid; brake fluid; hot/cold water; ketone; ozone; silicon resin liquid or steam under 200°C. AIGI 147 Silicon Rubber Sheets AIGI 147 Silicon Rubber Sheets could stand for high and low temperature, stable physical properties at a wide temperature range: -60°C~250°C. It also offers ozone resistant and weatherability. It is used under air; Ethylene glycol; ozone; UV rays; etc..
German standard flexible rubber joint Single Rubber Joint 1. Flanged single sphere expansion rubber joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping Working Pressure(Bar) 10 16 25 Bust pressure(Bar) 30 48 55 Vacuum(mm Hg) 400 650 750 MATERIAL OF EACH PARTS No. Part Meterial 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR, CR, IIR, NBR, FKM, EPDM, PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 Flange Cast and forged carbon steelStainless steelPlastic (CPVC, PVDF, PPH, UPVC, RPP)
British standard flexible rubber joint Rubber Joint 1. Single Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping Working Pressure(Bar) 10 16 25 Bust pressure(Bar) 30 48 55 Vacuum(mm Hg) 400 650 750
Thread Rubber Expansion Joint JGD-B Thread Rubber expansion Joint Rubber Jointhas the characteristics of good sealing, light weighting, easy to fix and maintain, also has long working expecting, but please keep far away from sharp metal in order to avoid breaking the rubber body. Equipped with the excellent comprehensive performances of rubber expansion bellows, thread rubber bellows can be used for lift and transportation of raw water and sewarubberge, transportation of water supply, cooling cycle water of thermal power plant, condensate water of metallurgy industry and chemical materials of chemical industries, cooling and dilution of oil and chemical industries and flexible connection of other industries. It is also suitable to transport all grain and powder material and gas for its high abrasive resistance. Due to its good integral function, flexible rubber joint is used widely in key projects of chemical industry, construction, water supply, drainage, petroleum, light and heavy industry, refrigeration, health, fireproof and power, etc. Rubber Bellows Joints: 1, Versatile hand-built construction. Made in China 2, Absorbs directional movement 3, Absorbs vibration, noise and shock 4, Compensates for expansion 5, Wide flowing arch design 6, Virtually eliminates sediment buildup 7, Economical fully molded construction 8, High vacuum rating (up to 30" Hg) can be supplied for certain sizes 9, Special grooved flange ring design, prevent rubber end pulling out 10, Solid galvanized steel floating flanges speed the installation time 11, High tensile aircraft cable is embedded in the raised face rubber ends to prevent pull out and avoids the sharp cutting edge of solid steel rings 12, No gaskets required; integrally rubber flanged design, no gaskets required, DIN PN10/16 drilling standard, other flange drilling available, including ANSI 150lb/300 lb, BS, and JIS No. Part Material 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR CR IIR NR FKM EPDM PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 threaded union rubber joint Cast and forged carbon steel(Q235), Stainless steel(201, 304, 316, 321), Plastic(CPVC, PVDF, PPH, UPVC, RPP)
Flexible Rubber Elbow Rubber Joint Flexible rubber joint is also called shock absorber, pipe shock absorber, shock proof box and soft joint, and so on. It is a pipe joint of high-flexibility, high-gas tightness, resistance to medium and climate. It has such functions as following: 1. Small volume, small weight, good flexibility, easy installation and maitenance. 2. It can make horizontal, axial and angular displacement when being installed. It cannot be restricted by the obstruction of pipe and the non-parallel of flange. 3. It can reduce noise passed through structure when it works and has strong shock absorption. 4. Our company personally develops inner non-seal high-pressure rubber joint that can prevent effectively inner wall of rubber joint from the corrosion in the pipe of high-temperature resistance, acid and alkali resistance and oil resistance to improve the use life. (1) Economy: Compared with the systems of mechanic stretching and material damping, it has the advantages of little space covering, light weight, easy assembly and disassembly, labor saving and low cost. Its smooth inner wall can reduce flow resistance. It has good water tightness, so there is no need of gasket during the installation. It has wide application, large temperature-resistance scope and long working life. (This product can be used for 20 years if it is used indoors. ) (2) Displacement: Flange is free from pipe decentraction and imbalance. Its good flexibility allows compression, extension, distortion, deflection of vertical displacement, etc. Which can prevent the pipeline from damage of deformation and foundation settlement arising from expansion caused by heat and contraction caused by cold. (3) Shock and noise absorption: The large damping of rubber sphere can effectively buffer and isolate vibration, control and reduce mechanical vibration, and absorb fluid impact noise. The reasonable installation between vibrating machine and metal pipe can decrease structure-borne noise by 15-25 decibels. (4) Pressure resistance: The multilayered sphere structure can especially endure internal pressure, withstand strong blasting force and impact, and prevent deformation from external pressure. There are many pressure standards on work piece. (5) Reducibility: After external force compressed, it can recover to original state when this force is removed. (6) Wide application: Different rubber material and formula can make product possess different resistance to heat, oil, corrosion, age, abrasion and ozone.
American standard flexible rubber joint Single Rubber Joint Rubber Joint 1. Flanged single sphere expansion rubber joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping Working Pressure(Bar) 10 16 25 Bust pressure(Bar) 30 48 55 Vacuum(mm Hg) 400 650 750 MATERIAL OF EACH PARTS No. Part Meterial 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR, CR, IIR, NBR, FKM, EPDM, PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 Flange Cast and forged carbon steelStainless steelPlastic (CPVC, PVDF, PPH, UPVC, RPP)
Flexible Rubber JointJGD (KXT) Single Rubber Joint Rubber Joint, Rubber Joint Supplier 1. Acid resistance Flexible Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5.
Flexing Can Double Ball Rubber Joint KXT Multi-Sphere Rubber Joint Rubber Joint High pressure resistant Rubber Joint, is mainly the use of rubber unique properties, such as high flexibility, high air tightness, chemical resistance and radiation resistance, high strength, strong cold stability bias ply polyester composite Hou contrast, high pressure, high temperature molded cross-linked internal high density, can bear high pressure, high elastic deformation effect. Constructed of neoprene and nylon (other materials are available see charts below), the spherical shape allows pressure to exert itself uniformly in all directions, thus reducing the force exerted on pipe lines and equipment. Bias-ply tire cord provides strength, a high safety factor, and low force to move. Precision molding provides a dense, uniform carcass. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping Bust pressure(Bar) 30 48 55 Vacuum(mm Hg) 400 650 750 MATERIAL OF EACH PARTS 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR, CR, IIR, NBR, FKM, EPDM, PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 Flange Cast and forged carbon steelStainless steelPlastic (CPVC, PVDF, PPH, UPVC, RPP)
Clamp Flexible Rubber Joint Clamped Rubber Joint Rubber Joint 1. Oil resistance Flexible Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement axial expansion, etc. 2. According to different materials, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange standard: ANSI, JIS, BS, DIN, GB, ect Item No. Parts Name Parts Material 1 Hoop Q235 304 316L 2 Outler layer glue IIR, CR, EPDM, NR, NBR 3 Skeleton layer polyester cord 4 Inner layer glue IIR, CR, EPDM, NR, NBR
Limited Flexible Rubber Joint KXFT Single Rubber Joint Rubber Joint The product is mainly used for conveying liquid, gas, solid materials such as metal pipe flexible connection can compensate for displacement, vibration isolation noise, is a novel rubber damping products. High Strength Rubber Joint combines the mechanical extensibility of the metal expander and the multi-displacement function of the flexible rubber joint. It is not only mechanically expandable for installation and dismantling but also compensates for changes in the temperature of the pipe during operation Linear expansion and contraction as well as compensate for the ground settlement caused by the pipeline center of gravity and other causes of angular deviation, but also to eliminate vibration and noise transmission, is a versatile pipe compensator. Features Minimal axial dimensions Limited weight Low warping forces High-resistance to work High-capacity acoustic damping No. Name Meterial 1 Inner & Outer Rubber NR, NBR, EPDM 2 Key Frame Nylon cord fabric 3 Reinforcing Ring steel wire 4 Flange Q235
PTFE flexible rubber expansion joint Single Rubber Joint Pipe Expansion Joint 1. Acid resistance Flexible Rubber Joint can greatly reduce pipeline system vibration and noise, can solve the problem of joint displacement, axial expansion, etc. 2. According to different materials manufacture, flexible rubber joint can be made into many kinds: acid resistance, alkali resistance, corrosive resistance, oil resistance, heat resistance, adapt to many mediums and different environment. 3. Material is polar rubber, good sealing, light weight, easy installation, long service life, avoid contacting with sharp metal device. 4. If use overhead, can match with elastic support, when installation, bolt with diagonal method to tighten up. 5. If pipeline pressure is high, use bolt connect the flange both ends. 6. Flange connection standard is GB4216.3-4216.5. No. Part Meterial 1 Body NR, CR, IIR, NBR, FKM, EPDM 2 Inner & Outer Rubber NR, CR, IIR, NBR, FKM, EPDM, PTFE 3 Body Carcass Nylon cord fabric 4 Reinforcing Ring Multi-strand coppering steel wire 5 Flange Cast and forged carbon steelStainless steelPlastic (CPVC, PVDF, PPH, UPVC, RPP) MAIN DATA Nominal Diameter(DN) Length L Axial displacement Horizontal Isplacement Angular deflection mm inch mm Extension Compression mm (a1+a2) 32 1¼ 95 6 9 9 15º 40 1½ 95 6 10 9 15º 50 2 105 7 10 10 15º 65 2½ 115 7 15 11 15º
UHMWPE fender is made of 100% UHMWPE material which will not warp, crack, splinter or corrode.It has become a popular product which is widely used in dock as it is UV resistance and no water absorption.UHMWPE fender still has the performance of prolongation and high tensile strength and could immersed in seawater perennially. The most important is that Ultra-high molecular weight polyethylene (UHMWPE) dock fender could avoid the impact damage between ships and dock .Because of the high impact resistance performance, UHMWPE dock fender instead of the traditional steel ones is widely used in ports and docks at home and abroad.
Prefabricated Rubber Running Track, composed of two different layers vulcanized together. The formulationof the top layer is different from that of the bottom layer. The vulcanization process guarantees molecular bond between the two layers. The end result is a continuous, seamless piece of material. The rubber-based top layer provides outstanding elasticity. The unique non-directional surface embossing, free of surface coatings and loose granules, provides greater contact area than other tracks surfaces, as well as greater water flow efficiency in rainy conditions. EPDM synthetic rubber vulcanization of the further strengthen of the materials of polymer, the good performance for Aging resistance, weather resistance, electrical insulation, corrosion resistance, impact resistance etc. Natural rubber has excellent properties of high elastic insulation, waterproof, low specific gravity, after appropriate treatment with alkali, heat, cold, pressure. Full solid be consistent from beginning to end, and has maximum compression deformation. Its advanced partition design maximizes absorption and recovery of energy. Application: for athletic field & athletic running track material of high school, university, physical college, sports center, stadium Certificate: IAAF Certificate, IAAF Class1st Athletic Facility Certifciate,ISO9001 and ISO14001 Installation: 1) Foundation requirements: asphalt, or, concrete. Using Scrapping machine to scrap the foundation very clean and very flat. Using Primer 0.2kg/m2 to brush on the foundation to avoid underground water rising and protect the running track system 2)Preparing installation tools, two components polyurethane adhesive, running track surface roll to start installation, installation of rolls should be from inner to outside, from straight runway to curve runway. 3)Lines marking after finishing installation of rolls Free samples !! After-sale service: Provide free training lesson for our oversea distributor or buyer, professional product & construction knowledge for you. WENDY TAM wendy@flysteptrack.com www.flysteptrack.com
Features: 1. water Solubility 2.Nonpollution 3.Short Construction 4.Moderate Thickness 5.Good Wear-Resistance 6.Weather Resistance 7.Water-proof 8.Slip Resistance 9.breathability and colorful
Chemical Name:N-Cyclohexyl-2-benzothiazole sulfenamide Molecular Formula:C13H16N2S2 Molecular Weight: 264.41 CAS NO:95-33-0 EINECS NO.: 202-411-2 Specification: Appearance Gray-white powder Gray -white granular Initial M.P. oC� 98.0 98.0 heating loss %� 0.30 0.30 Ash%� 0.30 0.30 Residues on sieve(150μm), % � 0.10 Properties:Gray-white powder (granule) with a little odor, no poison. The density is 1.31-1.34. M.P.: 98oC above. Soluble in benzene, boluene, chloroform, CS2, CH2Cl2 acetone, ethyl acetate, hardly soluble in alcohol, insoluble in water, gasoline, acid / alkali with lower concentration Application:CBS has excellent scorching property, high curing rate, high modulus of vulcanized rubbers, wide range of application. It is a sulfenamide accelerator with the highest activity in EPDM. Packing:25kg in kraft paper bag with PE bag inside. Storage:Stored in cool, dry and draughty place; avoid direct sunlight; protect against moisture or high temperature. The validity is 2 years.
Type: Single Type, Double Type, BSP/NPT Thread Type Size Range: DN25-DN1600 Material of Rubber ball: CR, NBR, EPDM, HYPALON, VITON Material of flange: Galvanized Steel, Stainless Steel Working temperature: -20â?? to +115â?? Ball length for Single Sphere: 130mm, 150mm, 95mm-300mm Ball length for Double Sphere: 175mm-345mm Ball length for Union Type: 200mm for DN15-DN50, 240mm for DN65-DN80. Thread End Connection: BSP or NPT thread Flange End Connection: EN1092-1 PN10/PN16, ANSI150, BS4504, AS2129 Table D/E. Working Pressure: PN6, PN10, PN16, PN25 Application: water, warm water, seawater, weak acids, alkalis, etc... Easy installation and remove; absorbs vibration, noise and shock -
Description: the natural rubber sheet, gum rubber sheet are made by ROTOCURE vulcanizing press or plain vulcanizing press with high quality natural rubber(NR). The natural rubber is from the natural rubber tree with middling hardness and high tensile strength, high elongation, good abrasion resistance, elasticity, safety and nontoxicity without smell. The pure natural rubber sheet is also named gum rubber sheet or para rubber sheet. 1-6mm thickness is made by ROTOCURE vulcanizing press with shiny surface, 7-80mm thickness is made by vulcanizing press for get higher thick thickness. Working under the higher pressure, wearing resistant, food grade lining status at the temperature of -35°C - +85°C in air or water. Apply to punch all kinds of seals, gaskets, lining and others applications with its good function, for example of truck lining, drinking water lining, rubber membrane special for PVC vacuum laminating press. Specifications: material: pure natural rubber or NR/SBR quality: industrial grade, food grade color: black, white, brown, beige, red, green etc. surface: smooth/smooth, smooth/impression fabric, double impression fabric tensile strength: 2-24Mpa hardness: 35, 40, 50, 60, 70, 80+/-5shore A elongation: 170%-760% density: 1.05-1.70g/cm3 working temperature: -35°C - +85°C thickness: 1.0-50.0mm width: 0.1-3.6m length: 1.0-20m Insertion: reinforce to insert 1-3PLY fabric natural rubber lining sheet: top: cured natural rubber with red or black bottom: uncured neoprene rubber with light yellow quality: industrial grade, food grade surface: smooth/smooth tensile strength: 13-18Mpa hardness: 35, 40, 65+/-5shore A elongation: 400%-650% density: 1.05-1.15g/cm3 working temperature: -35°C - +85°C thickness: 1.0-25.4mm width: 1-1.5m length: 10-20m
Physical character: made with high quality silicone rubber on drum-type vulcanizing press or vulcanizing press according to the different request from the buyers. We depend on the advanced manage, innovative technique and strict quality control with excellent silicone rubber material and machine, ravel out the problem of lower smooth surface and high thickness tolerance of Rotocure vulcanizing machine, and also ravel out the problem of restricted width, length and visible joint on press vulcanizing machine. It is triumphantly without joint and with infinite length under the above mentioned excellence. We have the super-wide drum-type vulcanizing press with 4000mm width and high quality products maximum 3800mm width without joint. High quality silicone rubber with good performance of anti-aging, ozone resistance, heat-resistant, electric insulation, oil resistance, solvent resistance, corrosion resistant, nonpoisonous and tasteless, pollution-free. Working in air, water, oil and other medium at the temperature of -60C - +260C(moment maximum 300C) with the high stability, reliability and surface inactive without sticky. Apply to punch all kinds of rubber seal gasket or special for PVC vacuum laminating press, wooden door vacuum laminating press, glass vacuum laminating press, solar vacuum laminating press, hot laminating press and card laminating press etc. Specifications: Material: 100% virgin silicone rubber from Germany or China Quality: high tear resistant or middle tear resistant Color: translucent, dark red, black, milk white, grey, blue etc. Surface: smooth/smooth, smooth/impression fabric, smooth/sanded Insertion: reinforced and insert 1 PLY fabric Tensile strength: 7-12mpa Hardness: 15, 20, 30, 40, 50, 60, 70, 80+/-5shore a Elongation: 350%-760% Density: 1.25-1.30g/cm3 Tear strength: 26-42n/mm Working temperature: -60c - +260c(moment maximum 300c) Thickness: 0.1-30mm Width: 0.5-3.8m Length: 1-50m Grade: industrial grade, food grade Press: Germany silicone for "+" and "-" press Chinese silicone for "-" press only. -
The pad printing silicon rubber usages: The silicon rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys, trade makers .Silicon pad printing is a carrier which transfer printing the patterns on the steel plate onto the toys products surface. Pad printing silicon rubber features: Pad printing silicon rubber with high print times and abrasion resistance, without any inpurities, with good printing effects, permanent and durable, we can provide all kinds of colors are available and our catalyst is free charged. Pad printing silicon rubber operation instructions: Pad printing silicon rubber is two-component silicone, part a is the liquid silicon rubber, part b is the catalyst. The usual mxing ratio for silicone rubber and catalyst is 100 : 2-3, eg. We take 100grams of liquid silicon rubber, then we add 2-3 grams catalyst, mix then evenly and pour it to your mold. Then after 2-4 hours, you will obtain a printing pad. Frequently asked question of pad printing silicon rubber: The reasons why the silicon pad has a short service life are listed as follows: (1)the problem caused by inappropriate filtration of silicone rubber, and impurities in the packaging process due to the uncleanness of barrels and bags. (2)the short service life of the silicone pad has a close relationship with the adding amount of silicone oil. The more the silicone oil added, the softer the silicone pad will be. The silicone oil will destroy the molecule of the silicone rubber, thereby bringing about the non-durable and easy ageing of the silicone pad.
