Size: 10*105*1950mm Material: cedar, paulownia, japanese cypress Color: natural Useage: interior decoration for wall. Carton package 16pcs /carton.
We are the leading manufacturer of wood products, such as Hinoki solid wood wall panel, wood floor,wood furniture, edge glued panel, finger jointed panel and so on. Thickness: 12/14/18/20/25/27mm Width: 100--1220mm Length: 500--2440mm Usage: furniture making, construction. Package: pallet package.
Polyurethane foam sandwich panel is fit for the projects which have serious require of keeping warm. Polyurethane core material is considered to the best material in keeping warm and thermal insulation. The Polyurethane block material become steady after it froth, then combining with metal plates. The characteristics of this technique are: The polyurethane froth, after this chemical reaction is stable, we cut the polyurethane into pieces which with different thickness. The polyurethane sheet material has stable physical performance, it can combine with prepainted gaivanized steel sheets, the surface is smooth and the whole performance is excellent. The characteristics of polyurethane foam sandwich panel: Polyurethane foam sandwich panel(the abbreviation of Polyurethane is PU sandwich panel)have characteristics of high load intensity, small water-absorptivity, and the stability in either low temperature or the high temperature is good, the service life is long, thermal insulation performance is outstanding and so on. Good supporting, heat resistant, sound-insulated, sound absorption, light quality, non-toxic, odorless, green environmental protection. Polyurethane foam sandwich panel can cementation with the steel plates, the cements, the fiberboards, the bricks and many kinds of materials very strongly, in usual situation, it would not fall off and still strengthen its thermal insulation and waterproofing effects. The unique produce foaming craft made the products have exquisite and even abscesses, the Thermal conductivity is low, the size stability is good, is very suitable for both of the low pressure and the high pressure construction. Polyurethane foam plastic, s thermal stability is quite good, when the temperature is lower than 120 C, the volume and the intensity have no obvious change, its Thermal conductivity is small, when the density is 0.03kg/m3, the heat conductivity is only 63J(m. H. K)(15cal/m. H. K). It can be widely used as structural materials and heatproof materials in petroleum industry, chemical industry, construction, packing, refrigeration, military industry, space industry, aviation, transportation and industrial model design and other various aspects. w;1150mm,L:
Metal panel insulated with rock wool for roofs and walls which require a high degree of resistance to fire. The HKF-RW panel is constituted by two sheets with inter posed layer of orientated fibre high density rock wool, arranged perpendiculary to the plane of the panel and positioned in strips, laid longitudinally with offset joints and transversally compacted, completely filling the space between the two supports. Resistance to fire Rook wool is non-combustible material, so the rock wool panel has good fire-resisting property. The test shows temperature of the panel fire-proof is as high as 1000C, the test results obtained by Istituto Giordano S. P. A is as follow: Roof and Wall panel thickness 100 REI 120 Roof and Wall panel thickness 80 REI 60 Roof and Wall panel thickness 50 REI 30 The roof and wall panels, thickness 50-80-100mm, were classified 0/1 for reaction to fire. (Materials are assigned a class from 0 to 5, the higher the class, the higher degree of combustion. ) Effective Characteristic of Sound Resistant. Rock wool panel achieves a notable reduction in air borne sound transfer, particularly when specifying a perforated liner. The impact of rai and hail on the metal sheet, a problem on most standard constructions, is greatly reduced when adopting HKF-RW panel in thicknesses of 50-100mm with 100kg/m3 rock wool fibre insulation has achieved results of RW=29-30 dB according to UNI 8270/7 and 717/82. w;1150mm,L:
Exterior House Wall Panels by BV7S-001 Wood Pattern Sandwich Panel is often using on mobile house, villa house, holiday house. Structure 3 layers: Surface: 0.3 mm Al-zn alloy coated steel sheet (Al 55%, Zn 43%) Middle: 16mm PU foam Back : Aluminium foil paper Size: Length (3000mm-6000mm) Width:380mm Thickness: 16mm Weight: 3.7kgs/sqm Application Sandwich panel is widely used for Exterior wall cladding and Interior wall Insulation and Decoration in the filed of PEB house, Villa, Steel Structure buildings, Hospital, Old Building renovation, School, Library, Supermarket, Plant, Train Station, Residence and so on!
Professional supplier of Oak FJ Finger jointed panel, Oak EG Edged glued panel, Beech FJ Finger jointed panel, Beech EG Edged glued panel, Rubberwood FJ Finger Jointed panel, Rubberwood EG Edged Glued panel, Pine Finger Jointed Panel, Pine EG Edged Glued panel Get more information
Grooved Acoustic wood slat panel Our wooden slats are beautiful and decorative wooden panels that are sound absorbing as well as aesthetically pleasing at the same time. With high-quality acoustic panels, each one can be easily installed on walls and ceilings, both in domestic and commercial applications; offering modern styling in every way. Product: Grooved acoustic wood slat panel Overall Dimensions: 10mm x 605 x 2440mm Slat width: 27mm The milling gap: 13mm Key Features 1. Designed for both residential and commercial use 2. Class A sound absorption 3. FSC Certified real Oak veneered lamellas 4. Bonded to a rigid felt backing made from recycled plastic 5. Available in a 5 range of exclusive colours It was created with the purpose of improving peoples favorite spaces. If you have ever been in a room with bad acoustics, then you know the problem bad acoustics can drive you crazy But now you can do something about it, while also improving the looks in your room. Imagine a slat wall on an end wall in your living-room or on your ceiling. It would not only dampen the sound surely it would also provide you with a steady flow of compliments from everyone who sees it.
Polyester fiber sound-absorbing decorative panels with sound absorption, noise reduction, noise reduction, thermal insulation, thermal insulation, thermal insulation and other effects, the material is symmetrical and reliable, is a wide band of high-efficiency sound-absorbing materials. So how do you install a polyester sound-absorbing panel When installing the polyester fiber-absorbent panel wall with reserved back cavity, you can use straight clip type light steel keel to do the back attachment keel. In a good solid wall attached to the wall keel, the polyester fiber board with glue, or nail the method of connecting with the light steel keel. It has good flatness and stability. Directly affixed to the solid wall is as follows. 1. Pay attention to plate selection and plate-layout before construction. Pay attention to slight color difference, find out the center point of the paste surface, draw cross line, adopt the way of bricklaying, and start to line up the board from the center point (it is best to wear gloves to avoid pollution). 2.Cut the board surface Use steel ruler and sharp knife to cut or decorate accordingly, if you want to reduce the seam, you can tilt the blade inward by 0.5 1mm when cutting to facilitate the board edge butt, and reduce the gap. 3.Paste (1) Cement or wood base surface: can choose non-benzene universal glue or white latex made of neoprene rubber. (2) Base surface of paper gypsum board: under the premise that it is not easy to be damp, you can choose white emulsion glue or wallpaper glue made of cellulose as raw material (should be fixed with nails immediately after gluing to avoid the glue is not dry and the board surface moves). (3) Under the premise of easy or possible moisture, you can use universal glue. Polyester fiber sound-absorbing panels are porous sound-absorbing materials, it is easy to absorb glue, blocking holes, affecting the cavity after the sound-absorbing function. It is recommended that when constructing, you can brush glue on one side (only brush glue on the base plate or keel, the amount of brush glue is slightly heavier than normal). At the same time, you can also match the grain nail reinforcement. V-groove wall panels are CNC machine-cut to create 45 90 grooves in the surface of the PET acoustic panels. The paper size can be customized. It is widely used as a wall panel in wall spaces. Our Poly acoustic panels are made from recycled PET, which is also fully recyclable for complete acoustic panels, and we can cut CNC cut and UV printed panels on the surface that are lightweight, fire resistant, impact resistant, tacky, easy to install, and most importantly have high acoustic performance.
Designer: Deco Sound Acoustic wooden slat wall panels are decorative wall panels made of a series of horizontal wooden slats that are joined together. These panels are designed to absorb sound waves and reduce the amount of noise that is transmitted through a wall or ceiling. They are typically used in spaces where sound control is important, such as in recording studios, home theaters, and offices. Acoustic wooden slat wall panels are made from a variety of materials, including wood, fabric, and foam. They can be mounted on a variety of surfaces, including drywall, concrete, and brick, using a variety of methods, such as nails, screws, or adhesive. The panels can be finished with a variety of coatings, including paint, stain, or veneer, to match the decor of the space in which they are installed. In addition to their sound-absorbing properties, acoustic wooden slat wall panels can also be used for decorative purposes. They can add visual interest and texture to a room and can be used in a variety of settings, including living rooms, bedrooms, offices, and retail spaces. They can be used as a standalone feature or can be combined with other wall-covering materials to create a more cohesive design. Acoustic wooden slat wall panels are a functional and stylish option for reducing noise levels and adding visual interest to a space. Overall Dimensions: 22mm x 605 x 2440mm Slat width: 25mm The gap: 15mm Key Features 1. Designed for both residential and commercial use 2. Class A sound absorption 3. FSC Certified real Oak veneered lamellas 4. Bonded to a rigid felt backing made from recycled plastic 5. Available in a 5 range of exclusive colors It was created with the purpose of improving people's favorite spaces. If you have ever been in a room with bad acoustics, then you know the problem bad acoustics can drive you crazy But now you can do something about it, while also improving the looks of your room. Imagine a slat wall on an end wall in your living room or on your ceiling. It would not only dampen the sound but surely it would also provide you with a steady flow of compliments from everyone who sees it. Wooden slats panel
Pvc sequins Details of the sequins Material: pvc thickness: 24c-26c Colors: silver base color, laser bright color, transparent color, transparent bright color, cream bright color. Dull bright color Shape: flower, people, tree, leaf. Shell, round , maple, star, butterfly , and other requested. Oem: yes Package:500g/bag, 22.5kgs/carton Payment term: tt, lc , western union, money gram. Trade term:exw, fob, cfr , cif Moq: 100kgs/color Delivery time: about 20 days after receiving the lc or the deposit . Advantage: We are the factory, so the price will be much competitive. And the quality can be well controled. We can control all the production line so that can make everything going well. For about twenty years' exporting, we know clearly the quality in different countries. 500g per bag, 50 bags per carton
