Silicon-carbon alloy is a new type of alloy for converter, customers choose this to, replace most of ferrosilicon, silicon carbide and recarburizer, Used in converter, smelting deoxidation alloying process The characteristics Reduce the cost of steelmaking, increase economic, efficiency, improve product quality, stable performance, improve the quality of, molten steel, improve product performance, reduce the amount of alloy added,, reduce the cost of steel and increase economic efficiency.
Silicon carbide (SiC), also known as carborundum, is a compound of silicon and carbon with chemical formula SiC. It occurs in nature as the extremely rare mineral moissanite. Silicon carbide powder has been mass-produced since 1893 for use as an abrasive. Grains of silicon carbide can be bonded together by sintering to form very hard ceramics that are widely used in applications requiring high endurance, such as car brakes, car clutches and ceramic plates in bulletproof vests.
The characteristics: Reduce the cost of steelmaking, increase economic efficiency, improve product quality, stable performance, improve the quality of molten steel, improve product performance, reduce the amount of alloy added, reduce the cost of steel and increase economic efficiency. Silicon carbon alloy instead of ferrosilicon, silicon carbide, recarburizer, reducing the amount of oxygen scavenger, a converter for deoxidizing alloy, the effect of stability, steel chemical composition, mechanical properties and internal quality are better than the traditional process. By testing and production shows that using Si-C alloy to converter deoxy-alloy process, greatly reduce the cost of steel, creating considerable economic benefits, improve the market competitiveness of steel. The effect of using a silicon-carbon alloy species 1, can replace ferrosilicon and carburant, FeALSi dosage is also reduced, can effectively reduce the cost of steel 6-10 yuan / ton steel 2, smelting carbon steel, special steel and some low-alloy steel, the effective recovery of effective elements.
Ferro silicon is used as an essential alloy in the production of steel and cast iron. Ferro silicon is used to remove oxygen from steel and as alloying element to improve the final quality of the steel. Ferro silicon can also be the basis for manufacture of pre-alloys like magnesium ferro silicon (fesimg), used for modification of melted malleable iron. Main markets are the worldwide producers of alloyed, stainless and carbon steel. One of the fastest growing categories within steel is the stainless sector, in both flat and long products. Stainless steel has a specific consumption of ferro silicon 510 times higher than regular carbon steel. Special ferro silicon grades, like low al, high purity and low c ferro silicon, are used in the production of special steel qualities. Compared to regular ferro silicon, special grades of ferro silicon will help to keep both the content of inclusions and the carbon content in the final steel at very low levels. Ferro silicon is produced in submerged arc furnaces, using as raw material high-purity quartz, charcoal and iron ore.
The main grades our products cover: Grade Si Fe(max)Al(max)Ca(max)P(max) 553 98.5%min 0.50% 0.50% 0.30% 441 99% min 0.40% 0.40% 0.10% 421 99.2% min 0.40% 0.20% 0.10% 3303 99.3% min 0.30% 0.30% 0.03% 50ppm 2202 99.5% min 0.20% 0.20% 0.02% 40ppm Packing: In 1mt big bags Shipment: With in 15 days after comfirming the order Apperance:Dark gray Physical Property: High melting point and resistivity, good heat resistance and good anti-oxidation effect. Particle Size: (10-100)mm. Application and use: 1. Used in aluminum: An additive to aluminum alloys, silicon is used to increase the fluidity and tenacity of Aluminum and its alloys, which enjoy good castability and weldability accordingly. 2. Used in organic chemicals: Silicon metal is used in manufacturing a number of sorts of silicones, resins, and lubricants. 3. Used in electronic parts: Silicon metal is used in producing monocrystalline and polycrystalline silicon of high purity for electronic parts, such as semi conductors, etc.
Yellow silicone ring, in simple terms, the silicone ring made of yellow color. The color of the silica gel circle, can make any color, transparent, red, green, blue, black, white, translucent, and so on, products include silicone o-rings, silica gel, silica gel ring U, silica gel, silica gel Y type V circle, silicone rectangular circle, etc. The silicone ring is a ring!Silica gel is a kind of rubber material, wide because of its special properties of heat resistance, excellent chemical resistance, together with the fluorine rubber was thus became a special rubber.Silicone is widely used in making all kinds of seals, including silicone RING, silicone O - RING, silicone sets, etc. Silicone ring has excellent heat resistance, low temperature flexibility and special excellent oxidation and ozone resistance, high permeability and selectivity of gas through.Good electrical insulating properties (volume resistance is greater than 10 cm, breakdown voltage in more than 30 kv/mm), corona resistance and arc resistance.But add a conductive carbon black, nickel powder, aluminum powder, silver powder, and can get the appropriate electrical conductivity (volume resistance to 5-0.02 euro. Cm).The surface of the silica gel circle can lower, with moisture absorption and isolation effect.Water resistance, but poor resistance to water vapor, the pressure more than 50 psi is not recommended.Compatible with most of the oil, chemicals and solvents.General silicone rubber acid-proof alkaline, polar solvent resistance, resistance to hydrogen alkanes and aromatic oils.Not recommended for most concentrated solvent, oil, concentrated acid and diluted caustic soda solution.Special silicone rubber has radiation resistant, flame resistant, oil resistant performance.Its low tensile strength, abrasion resistance is weak, is generally not used for dynamic seal. The silicone ring is based on the silicon from quartz, and adhered to by the silicon atoms such as methyl, vinyl side chain to form a saturated nonpolar rubber.The different side chains can lead to silicone rubber with different properties.Methyl vinyl silicone rubber (VMQ) is a kind of silicone rubber material application. -
Characteristics The industrial silicon powder is also called metal silicon powder. It is silver grey or dark grey powder and appears metallic luster. Its characteristics are high melting point, good heat-resisting, high resistivity and excellent anti-oxidation. It's well known as the industry gourmet powder used as the indispensable basic raw materials of a lot of high-tech products. Application Industrial silicon powder is widely applied to the refractory material, powder metallurgy industry so as to improve the products heat-resisting performance, wear resistance and oxidation resistance. The products of the refractory material, powder metallurgy industry are used in the steelmaking furnace, kilns, etc. Standard Size: 200Mesh; 325Mesh; etc The packaging and granular size can be produce according to customer demand. Si Fe Al Ca 98.5% 0.5% 0.5% 0.3% 99.0% 0.4% 0.4% 0.1% 99.0% 0.3% 0.3% 0.03% 99.0% 0.2% 0.2% 0.02%
Characteristics Ferro Silicon Magnesium nodulizer ( FeSiMg ) uses the advanced smelting craft production the nodulizer product, the organization is compact, the ingredient is stable, does not have the deflection evenly, the MgO content is low.The spheroidization response is steady, the magnesium absorption rate is high, the anti-decline time is long. After spheroidizing, the stone ball not a strike circle entire, tiny, the tendency is small. Strong spheroidizing ability, stable composition and reaction. Application Ferro Silicon Magnesium nodulizer ( FeSiMg )Used for nodular cast iron, adding hot metal can play a role in spheroidizing, desulfurization and outgassing. It can also improve the molten iron purity; generate compound insoluble in water with arsenic, zinc, tin, lead and other low melting point impurity. Standard Grade Chemical Composition (%) Mg Re Si Ca Al Ti Fe FeSiMg5Re2 4.0-6.0 1.0-3.0 38-44 2.0-3.0
Characteristics 1.Calcium Silicon Barium Inoculant ( CaSiBa ) increase the graphitization core, refinement of graphite, promote get A type graphite from the Grey iron castings, increase the intensity, for ductile iron parts, it can make the graphite in ductile iron ball small, round, improve the nodulizing grade. 2.Calcium Silicon Barium Inoculant ( CaSiBa ) effectively reduce molten iron super-cooling degree, promote the precipitation of graphite, significantly reduce chilling tendency, reduce the relative hardness, improve casting machinability. 3.Calcium Silicon Barium Inoculant ( CaSiBa ) easy to dissolve and absorb than the average inoculant. can reduce the gascontent in the molten iron. 4.Calcium Silicon Barium Inoculant ( CaSiBa ) hight ability to recession-proof. at the same time it prevent relevant nodulizing decline, wall thickness sensitivity is small, well-closed formation. Standard GradeChemical Element (%) SiCaBaAlPS â?¥(Min)â?¤(Max) Ca10Si50Ba1350.010.013.03.00.050.05 Ca13Si45Ba1045.013.010.0 Ca11Si45Ba1345.011.010.0 Ca9Si45Ba1345.09.010.0 Ca7Si45Ba1545.07.015.0 Ca5Si45Ba1545.05.015.0 The specification,packaging and granular size can be produce according to customer demand.
Characteristics Ferro Silicon ( FeSi ) used as deoxidizer and alloying agents in the steel industry. In order to obtain qualified chemical composition and guarantee the quality of steel, in the last stage of the steel must be deoxidized. The chemical affinity between silicon and oxygen is very large, Thus ferrosilicon is strong deoxidizer used in sedimentation and diffusion deoxidation of steel-making. Add a certain amount of silicon in the steel, can significantly improve the strength, hardness and elasticity of steel. Standard GradeChemical Element (%),, SiAlSPC â?¥(Min)â?¤(Max), FeSi65652.00.020.040.2 FeSi70702.00.020.040.2 FeSi72722.00.020.040.2 FeSi75752.00.020.040.2 Size: 10-50mm; etc. The content packaging particle size may be based on customer demand production.
Characteristics Ferro Silicon Barium ( FeSiBa ) is a kind of good deoxidizer and desulfurizer. 1. Deoxidization ability strong, Good molten steel flow, Completely solve the problem of the nodular casting nozzle. 2. Significantly improve the recovery rate of the silicon, manganese, etc. Reduce the addition amount of carbon powder. 3. The desulfurization effect is obvious, Shortening the period of steelmaking. Application 1.Wide range of application, Can part instead of deoxidizing agent in steelmaking, Eg: aluminum wire, silicon barium aluminum, ferro silicon aluminum, the calcium silicon wire, etc.2.Easy to use, simple operation, Donâ??t need to add any auxiliary equipment. Standard Grade Chemical Composition (%) BaSiAlC â?¥(Min)â?¤(Max) FeSi50Ba30305030.3 FeSi40Ba25254030.3 FeSi45Ba20204530.3 FeSi50Ba15155030.3 FeSi55Ba10105530.2 FeSi60Ba556020.2 FeSi65Ba226520.2 The specification,packaging and granular size can be produce according to customer demand.
Characteristics Rare Earth Ferro Silicon ( RE FeSi )adopts the one-stage process production and gets its form in secondary thin pouring. It also has the high Si content, high Re retrieving, easy to adjusting and other characteristics.The product is assembly compacted, with even chemical composition. It is with silver-gray appearance and metallic luster. Hard and easy to crush. Application Rare Earth Ferro Silicon ( RE FeSi ) is suitable to be used as the additive in steelmaking and iron-casting, or as the intermediate alloy of rare earth. It can also serve as the inoculant of gray casting iron, ductile casting iron and vermicular casting iron. It is the important additive in all kinds of inoculant, nodulizing and vermiculazing agent. Standard Grade Chemical Element (%) Re Si Ba Ca Al Ti Mn Content â?¤(Max) FeSiRe25 24.0-26.0 55-65 2.0 2.0 1.5 0.3 0.5 FeSiRe27 26.0-29.0 50-60 FeSiRe30-A 30.0-32.0 50-55 FeSiRe30-B 29.0-30.0 50-55 Size: 10-50mm; etc The specification,packaging and granular size can be produce according to customer demand.
Si: 40-50 % Ca: 10-20 % Mn: 10-20 % C: 1.0 % max. P: 0.05% max. S: 0.04% max. Fe: 15 % max. Al: 1.5% max.
Mc pu series, hardness available from 15 shore a to 95 shore a Mix ratio 1 1 De-mold time 8hrs 6hrs 3hrs Full cure 24hrs Why choose mc polyurethane rubber? Firm yet flexible mold rubbers Ideal for demanding, high production casting and forming of concrete Dimensionally stable molds can last for years Abrasion resistant for long mold life Easy to use, forgiving formulations All products share the same high performance Package: A and b 1kg, 5kg, 20kg, 200kg
Description of platinum curing mould making liquid silicone rubber Addition cure silicone is a kind of two part silicone rubber in addition cure or platinum cure type with mixing ratio of 1:1 or 10:1. It can cure at room temperature as well as under heat. It's a kind of food grade silicone and mainly used for mold making. Application of platinum curing mould making liquid silicone rubber Silicone rubber is mainly used for making molds of tire, concrete stone, grc, polyurethane products; wax, candle decoration; rapid prototyping and tyre molds; chocolate, candy and similar products.
1.Unsaturated polyester resin, epoxy resins, polyurethane resins 2.Polyurethane elastomers 3.Natural and synthetic waxes 4.Plasters and cements Features of silicone rubber 1.Curing agent arrange together as free charged. 2.In liquid form and in various colors 3.With and exceptional fluidity and good operability 4.Temperature and deformation resistance as well as low shrinkage 5.High duplication times6.Samples orders are available 7.Moq:200kg Silicone rubber are generally named: Two-component room temperature vulcanization silicone rubber , a kind of elastic silicone rubber mold which features with resistance to deformation.High-temperature, acid-alkali and expansion, it mainly applicable to make the silicone mould for cultural relic duplication , architectural decoration, resin crafts , lighting ornaments , candles , statues mold design, product exploitation etc. Instruction for using silicone rubber for mold making to make molds. Step 1:preparing mold. Once you have your model to mould you need to build a box from wood/acrylic to contain the silicone and get a good covering over your model , the size and shape of this container is totally depends on shape of the model , remembering to leave plenty room surrounding the model so that you will have a strong wall thickness (at least 20mm) Note:small models can be cast in sourced containers like tins , ice buckets , cake tins, etc
Silica, silicon carbide, silicon carbide, also known as carbon refractory sand, is made of quartz sand and petroleum coke, sawdust and other raw materials in smelting in electric resistance furnace, high temperature and be become.Green silicon carbide black silicon carbide and silicon carbide two commonly used basic varieties: (1) black silicon carbide containing SiC by about 95%, its toughness is higher than the green silicon carbide, mostly used for processing low tensile strength of material, such as glass, ceramics, stone, refractory material, cast iron and nonferrous metal, etc.;(2) the green silicon carbide containing SiC98 % above, good self-sharpening, mostly used for processing hard alloy, titanium alloy and optical glass, also used for honing cylinder jacket and fine grinding HSS cutting tools.
1, Main silicon carbide abrasive, stability of high hardness, toughness determined by sic grinding tool can be used in the manufacture of consolidation, coated abrasive free grinding glass, ceramics, stone, cast iron and some non-ferrous metals, hard alloy, titanium alloy, high speed steel cutter grinding wheel, etc. 2, Refractory corrosion resistant material - main silicon carbide with high melting point (temperature), chemical inert reting resistance silicon carbide can be used for abrasive, ceramic products by burning kiln with shed board saggar, zinc smelting industry vertical cylinder distillation furnace with carbon silica brick, aluminum electrolytic cell line, crucible, such as a furnace material of silicon carbide ceramic products. 3, Chemical use, silicon carbide steel melt steel hydrolysis and free oxygen, metal oxide reaction of carbon containing silicon oxide slag for smelting steel cleaning agent is used for steelmaking deoxidizer cast iron tissue conditioner, generally with using low purity of silicon carbide to reduce the raw material for manufacturing silicon tetrachloride. 4, Electrical use, used for high temperature heating element, nonlinear resistance element semiconductor material silicon carbide heating element used in the 1100 ~ 1500 (furnace) nonlinear resistance element all kinds of lightning protection valve plates. 5, The far-infrared radiation coating or silicon carbide silicon dryer with far infrared radiation. New silicon carbide products is widely used in a particular industry, air conditioning, automotive engine, communications equipment, radar stations, the missile defense system, the space shuttle, and are used on aircraft carrier, especially in the aspect of space, some special parts, silicon carbide products to be reckoned with, and the effect of foreign resources, has the advantages of domestic, therefore, the development of an opportunity is also relatively well.
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms-tsm Application: industry Dimensions: requirements Chemical composition: carbon Sample: free Thermal conductivity: 1500-1800w/mk Density: 1.5-2.2g/cm3 Color: black Use temperature: -40?~400? Ul flammability rating: 94v0 Tensile strength: 9~40mpa Material: flexible graphite sheet Size: customizable
Place of origin: guangdong, china (mainland) Brand name: laimeisi Model number: lms Type: insulation sheet, thermal pad Material: silicone, thermal conductive insulation pad Application: high voltage, cpu gpu Rated voltage: 4kv Tensile strength: 10.4mpa Color: blue Thickness: 0.1mm-10mm Feature: excellent resistance item Name: silicone rubber thermal conductive insulation pad Certificate: rohs Hardness: 20-50 shores Size: customizable
