MX Self Priming Pump Size (discharge): 25mm to 450mm Capacity: 3.4~ 1200 m3/hr Suction lift: Max. 6.5m Head: 6m ~ 135 m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MX Self Priming Pump Introduction: MX Self priming pump made by our company is developed after our digestion, assimilation and improvement of domestic and foreign relevant technical data, which is a energy-saving kind of pump production. The pump is a kind of self-suction centrifugal pump, which has the advantages of compact structure, convenient operation, steady running, easy maintenance, high efficiency, long life, strong self-suction ability and so on. It doesn't need a foot valve on the pipeline, and just need to ensure that there is quantificational inducting oil stored in the pump case before work, so as to simplify the pipeline system and improve the working condition. MX Self Priming Pump Features: 1. Beautiful shape and fine structure,reliable performance. 2. With strong capacity of self priming, no need to equip with flap valve. 3. Non-clog, and with powerful capacity of passing big solid.. 4. Convenient for maintenance. MX Self Priming Pump Parameter Selection Table: MX Self Priming Pump Application: It is used in environment protection,construction,fire protection,chemical industry,phamary,printing and dyestuff,brewage,elctric power,electroplate,papermaking,petrol,washing for industry and mine,cool for device,etc. It is suitable for clear water,sea water and chemical medium with acid and alkali and mushy slurry(viscosity100 centipois),consistency for solid can not exceed 30% of total medium. When it's mounted with an arm sprayer, it can jet the water into the air to disperse into little raindrops for spraying, so it is a good tool for farm, nursery, orchard and tea garden. It is the ideal supporting pump for transfer slurry to filter press, it could matching with filter press of different specs and models.
MD Multistage Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MD Multistage Pump Introduction: Multistage Pump is single-suction,multistage,centrifugal pump,It is widely used for water supply&drainage infields of factories mines and cities.It is provided for delivering clear water without solid particles or other liquid which is physically and chemically similar to clear water. The temperature of the liquid is 0¡ãC~80¡ãC. Permissible inlet pressure is 0.6MPa MD Multistage Pump Features: 1. Stator: The main parts are suction casing, stage casing, discharge casing and diffuser. They are screw up by poles, to become a working house. It is horizontal, the discharge direction is upward; The discharge and suction direction of them are both upwards, and the suction direction is horizontal usually, also they can be made upward according to user's requirement. 2. Rotor: It is consist of shaft, impellers, balance dic and shaft sleeve etc. Shaft supplied power to impellers; The axial force is balanced by balance disc; The sleeve mounted on shaft to protect shaft. 3. Bearing parts: It is consist of bearing body, bearing and bearing cover etc. The bearing of type 85-67, 155-67, 600-60 pump is sliding bearing, lubricated by diluted oil, the other pump bearing is rolling bearing, lubricated by grease. 4. Shaft seal: It is usually adopted soft packing seal, consist of sealing house on suction casing, packing, blocking water ring, the sealing hose have some pressure water, to cool, lubricate and seal pump. The pumps usually adopt mechanical seal. 5. Drive: The pump is driven directly by motor through elastic coupling, the rotation of pump is clockwise looking from motor to pump. MD Multistage Pump Parameter Selection Table: MD Multistage Pump Application: Water supply and discharge in high-rise buildings Fire water supply in constructions Water supply and discharge in factories and mines Long distance delivery Cyclic pressurization in production
The product has own advantage not only carry is convenient,durable,labor-saving,but also have been acquired ZBY 89001-88 international standard. It's used to all kinds of charge,such as bike,motorbike,car tyre,buoy,air bed,ball series etc.
Hand press water pump Features: 1) bs-type hand-press pumps are suitable for delivering well water, river water, or any Kinds of non-corrosive water 2) this product has a good structure, stable property and long service life 3) rotary action 4) cast-iron construction 5) types: bsd, bsf
The AZ series centrifugal horizontal slurry Pump is Chinese design slurry pumps. It is advanced designed in oil lubricated frame could be more steady work in high pressure or the pumps in series. The impeller design is advanced and could be adjusted according to the requirement of the work site instead of using different type of pumps which is Min the pump and parts required and much easy to use and main. The AZ series centrifugal horizontal slurry Pump is widely used in power plant, metallurgy, mining, coal, building material and chemical industries to deliver abrasive fluid which is the best choice for updating old design slurry pumps! -!
Features: 1. Our pumps applied the single or double vane structure so that it can transfer sewage easily. It can transfer the fibrous matter which is with bore 5 times than pumps. 2. Seal the pumps with material tungsten carbide which is new, tough and corrosion resistant. All the same time we seal up the pumps with double-end, make it working in the oil chamber with long time safely, at least more than 8, 000 hours. 3. The structure of our pumps is portable, minimum-volume, non-noise and distinct energy-saving effect. Our pumps are convenient to repair and they can work as long as been put in water, this will save the cost much. 4. We installed the leak detection sensor which is high-precision and anti-jamming in the sealed oil chamber which can protect the pumps totally. 5. We can equip the automatic safety control cabinet according to the request from customer. Protect the leak, over-temperature and over-weight totally. 6. Float switch can adjust automatic according to the liquid, it can control the start and stop of pump, need not person to operate, it is very convenient for using. 7. We can equip double guide rail automatic coupling installation system according to the needs from customer; it can be convenient for repair and installation. 8. Our pumps can be used in the range and assurance the electrical machinery will not be overload. 9. There is 2 ways for installation: fixed type automatic coupling installation system and mobile free installation system.
Model DWP50CX(E) DWP80CX(E) DWP100CX(E) Type Self-priming centrifugal pump Suction*Delivery(mm)(inch) 50*50mm 2*2'' 80*80mm 3*3'' 100*100mm 4*4'' Total Heah 46m 32m 28m Suction Head 8m Max Delivery Volume 36m³/h 60m³/h 80m³/h Mechanical Seal Ceramic Engine Model DE170F(E) DE178F(E) DE186FA(E) Bore x Stroke 70 x55mm 78 x 62mm 86 x 72mm Displacement 219cc 296cc 418cc Engine Power 4.0hp 6.0hp 9.0hp Engine Speed 3600RPM Oil Capacity 0.8L 1.1L 1.65L Fule tank capacity 2.5L 3.5L 5.5 Starting System L Packing size(L*W*H) 535*445*495mm 590*495*530mm 690*535*555mm 20FT Container Loading Qty. 220units 176units 128units Net Weight 35kg 52kg 69kg
Model GE168 GE168-2 GE170 GE188 GE190 GE192 Type Air-cooled, 4-stroke, Single cylinder, OHV Displacement(cc) 163 196 209 389 420 439 Bore x Stroke (mm) 68x45 68x54 70x54 88x64 90x66 92x66 Speed(rpm) 3000/3600 Max.power(hp) 5.5 6.5 7.0 13.0 15.0 16.0 Max.Torque(N.m/rpm) 8.8/2600 10.8/2600 12.0/2600 26.5/2600 28/2600 30/2600 Starting System Recoil (Electric Start as optional) Fuel tank capacity (L) 3.6 6 Oil Capacity (L) 0.6 1.1 Fuel comsuption (g/kw.h) â?¤395 â?¤374 â?¤370 Ignition system Non-Contact Transistorized Megneto Ignition System Dimension (L x W x H) mm 385*330*350 455*420*475 510*420*475 Net Weight (kg) 16 17 18 32 32 33 OPTIONAL CONFIGURATION Electric start & battery | Pully | Clutch pully | 1/2 reduction gearbox | EPA(for United States market) | Key-way shaft, Taper shaft, Thread shaft
Model DWP50CX(E) DWP80CX(E) DWP100CX(E) Type Self-priming centrifugal pump Suction*Delivery(mm)(inch) 50*50mm 2*2'' 80*80mm 3*3'' 100*100mm 4*4'' Total Heah 46m 32m 28m Suction Head 8m Max Delivery Volume 36m³/h 60m³/h 80m³/h Mechanical Seal Ceramic Engine Model DE170F(E) DE178F(E) DE186FA(E) Bore x Stroke 70 x55mm 78 x 62mm 86 x 72mm Displacement 219cc 296cc 418cc Engine Power 4.0hp 6.0hp 9.0hp Engine Speed 3600RPM Oil Capacity 0.8L 1.1L 1.65L Fule tank capacity 2.5L 3.5L 5.5 Starting System L Packing size(L*W*H) 535*445*495mm 590*495*530mm 690*535*555mm 20FT Container Loading Qty. 220units 176units 128units Net Weight 35kg 52kg 69kg
Model GWP20CX GWP30CX GWP40CX Type Self-priming centrifugal pump Suction*delivery(mm)(inch) 50*50  2*2 80*80  3*3 100*100  4*4 Engine model GE168F GE168-2 GE188 Engine output (HP) 5.5 6.5 13 Displacement: (m³/h) 36 60 80 Lift: (m) 46 32 28 Suction: (m) 8 Fuel tank capacity (L) 3.8 3.8 6 Pipe diameter: (mm) 22 25 25 Starting system Recoil (Electric Start as optional) Dimension (L *W * H) mm 525*405*435 550*450*450 625*460*555 Net Weight (kg) 24 28 69 Gross Weight (kg) 25 30
ModelGWP20CXGWP30CXGWP40CX TypeSelf-priming centrifugal pump Suction*delivery(mm)(inch)50*50  2*280*80  3*3100*100  4*4 Engine modelGE168FGE168-2GE188 Engine output (HP)5.56.513 Displacement: (m³/h)366080 Lift: (m)463228 Suction: (m)8 Fuel tank capacity (L)3.83.86 Pipe diameter: (mm)222525 Starting systemRecoil (Electric Start as optional) Dimension (L *W * H) mm525*405*435550*450*450625*460*555 Net Weight (kg)242869 Gross Weight (kg)253070
Flow: 15m3/h Head: 39m Power: 4kw Material: cast iron Medium: clean water Outlet dia: 50mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 15m3/h Head: 54m Power: 4kw Material: cast iron Medium: clean water Outlet dia: 50mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 10m3/h Head: 108m Power: 5.5kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
Flow: 10m3/h Head: 21m Power: 7.5kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
Flow: 10m3/h Head: 135m Power: 9.2kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage.
Flow: 10m3/h Head: 150m Power: 9.2kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 10m3/h Head: 165m Power: 11kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 10m3/h Head: 180m Power: 13kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
Flow: 10m3/h Head: 195m Power: 13kw Material: cast iron Medium: clean water Outlet dia: 32mm Diameter: 175mm Speed: 2850r/min Voltage: 380V Phase: 3 phase/50Hz Color: Blue QJ Submersible pumps Parameters: Flow range10~500m3/h, Lift scope within 5~405m; Caliber scope 32~203mm, Temperature range-15~80° C. Products Overview: QJ Series submersible pumps widely used in farmland irrigation, spray irrigation and water-use, industrial and civil buildings, also the drainage system to level hills, mountain diversion and in low-lying areas dunes, urban and rural mining supply, drainage and other water conservancy facilities. Characteristics are that they are assembled into a simple structure they have installation convenience a small footprint, simple maintenance and a safe reliable operation. Product use conditions: QJ Submersible pumps use conditions 1. 380 V bias voltage does not exceed + -5% and 50 HZ frequency, and the deviation is not more than + -1% of the three-phase power supply. 2. Electrical cavity must be filled with water. 3. The first-class pump impeller should at least go into the dynamic water level 2 m below surface. Static pump unit immersed under water shall not be greater than 70 m. 4. Electrical from the bottom of the bottom of the well shall be not less than 3 m. 5. The water temperature no higher than 20 ° C, QJR-temperature hot water pump up to 80 ° C. 6. Water and sand content (by mass) of not more than 0.01%. 7. Water PH 6.5-8.5. 8. The hydrogen sulfide in water content is not more than 1.5 mg / L. Application : deep well water farm irrigation sprinkling irrigation urban and rural industry mine supply and drainage. Shenlong pump Ltd is located at the beautiful shore of the Yellow River and at the foot of the mountains of Mangshan, ZhengZhou City in the heart of Henan province. The company was created in the 1980s, And after the company's combined relentless efforts has become one of the largest modern enterprises in Henan that combines Research and Development (R&D), Prototype Design, Product testing, Advanced industrial production, and operational excellence. Shenlong pump Ltd is a design manufacture export professional company. Our Enterprise is Ministry of Agriculture. We are production and sales pumps around the world. The manufacture have strong technical force, with all kinds of machine tools, planer, drill press, etc. and The manufacture's total land area of over 660000 Square meters and with in excess of 300 equipment sets. Employing 860 staff members; amongst them over 40 senior technical experts. The allocation of B-level exceeds the national standard of computer Pump testing centers.
