Guangzhou Self Adhesive Foil Suppliers and Manufacturers

Features: 1, This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, natural stone material 2, The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3, Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4, Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5, Good anti-infiltration function 6, No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1, The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2, For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation process: 1, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2, Push the ceramic tile or heavy type ceramic tile above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material 4, Can be used for the old ceramic tile re-tread. Cautions: 1, Never mix the dry slurry with water and use again 2, For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3, For the painting surface, make sure the initial bond strength and no flake 4, Operating under 5¡æ~40¡æ situation 5, Clean the surface by little wet sponge or cloth before it dry 6, Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount) Technical reference using 3*3mm tooth scraper about 1.7kg/m2 1, adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) using 6*6mm tooth scraper about 3.0kg/m2 2, cool time: about 10min (cool time: the longest cool time that the adhesive can last ) using 10*10mm tooth scraper about 4.5kg/m2 3, dry time: 24h (according to the weather) 4, water resistance: excellent; non-toxic, prevent fire the smoother the surface, the less amount 5, when dry, anti-weak acid, anti-strong alkali and oil resistance 6, cut degree: £¾1.2MPa (14days later). Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag

Our products are made of imported raw materials and water-based inks. They are green, environmental friendly, uniform in color, wear-resistant and colorfast, lifelike and wood like, making your home decoration more environmentally friendly and natural. The product is stability, good weather resistance and high flatness. Products meet the European Union and the United States and other environmental standards. The products are in accordance with the highest U.S. fire safety standards UL-94 vtm-0. Product Characteristics: Low VOC emission Scratch-resistant Fire retardant Good texture clarity Weather resistant Good stability Small color deviation Damp and mildew proofing

Aluminum foil retangle, run, square and oval container. Different size Different size and weight as per custmer's market

All colors hot stamping foil Standard size: 0.64m*120m

Our Company Offer Good Quality Of Hot Melt Adhesive Include Glass Transparent And Normal Adhesive. Item Color Low Tempreture Light Yellow, White, Brown 130-150.C Middle Tempreture Light Grey, White, Brown, Light Yellow 150-180.C High Tempreture White , Brown, Light Yellow, Grey White 180-210.C

Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: bricks for wall using 3*3mm tooth scraper or 6*6mm tooth scraper, bricks for floor using 6*6mm tooth scraper or 10*10mm tooth scraper. Cautions: 1, Make sure the smooth and vertical rate of the surface before operation 2, Never mix the dry slurry with water and use again 3, For the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag

Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: the amount is related to the smooth, vertical rate, and thickness of the stone material Cautions: 1, make sure the smooth and vertical rate of the surface before operation 2, never mix the dry slurry with water and use again 3, for the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag

Features: 1. This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, and natural stone material 2. The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3. Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4. Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5. Good anti-infiltration function 6. No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1. The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2. For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation Process: 1. Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2. Push the ceramic tile or heavy type ceramic tile above it 3. For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Cautions: 1. Never mix the dry slurry with water and use again 2. For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3.For the painting surface, make sure the initial bond strength and no flake 4.Operating under 5¡æ~40¡æ situation 5.Clean the surface by little wet sponge or cloth before it dry 6.Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount). using 3*3mm tooth scraper about 1.7kg/m2. using 6*6mm tooth scraper about 3.0kg/m2. using 10*10mm tooth scraper about 4.5kg/m2. Technical reference: 1, Adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) 2, Cool time: about 10min (cool time: the longest cool time that the adhesive can last ) 3, Dry time: 24h (according to the weather) 4, Water resistance: excellent; non-toxic, prevent firethe smoother the surface, the less amount 5, When dry, anti-weak acid, anti-strong alkali and oil resistance 6, Cut degree: £¾1.2MPa (14days later). Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag.

Newest high grade aluminum foil. Box size:42*13.5*12.5cm; Carton size:43.5*28*27cm; 4box/CTN

ALL knid of hot stamp foil manufacturer Types of hot stamp foil. 1. Fabric and fabric gilding paper (cloth, clothing, etc.); 2. Soft and hard plastic gilding paper such as ABS, PVC, PMMA; 3. Electrical gilding paper with wire drawing, double-sided, transparent and mirror surface; 4. PP, PE gilding paper (cosmetics / daily necessities packaging); 5. OPP film, paper gilding paper (cigarette / wine box packaging); 6. Metal and glass gilding paper (cosmetics bottles, wine bottles, metal nameplates); 7. Leather / leather, suede gilding paper (leather, leather, shoe materials); 8. Wood / bamboo bronzing paper; 9. Process decoration with gold foil and silver foil; Suitable for hot stamping of ABS, PS, PVC, PC, PP, PE, nylon plastic, etc; High scratch resistance, high chemical resistance, high fingerprint resistance and strong covering force,It has passed the EU ROHS standard and SGS test. Welcome to discuss with me if you have any product request.

Self adhesive tape, double sided tape.

Foil bubble insulation sheet, epe, xpe foam thermal break, reflective foil laminate, aluminum foil, adhesive tape, bubble mailer, pool cover.

Easy to tear. Easy to wrap into various shapes. Transmit heat quick. Double sided available. Anti-oil and anti-sticking. Food grade safe. Thickened and not easily damaged. Household/commercial rolls are available.