Adhesive tape.
PTFE adhesive tape We selected fine imported fiberglass, wove it as the basic cloth and coat it with PTFE resin, proceed under high temperature condition, the product is called PTFE adhesive tape. Thickness(mm),width(mm),length(mm),Temperature(ºC) 0.08,10-1200,10-50,-70-260 0.13,10-1200,10-50,-70-260 0.18,10-2000,10-50,-70-260 0.25,10-2000,10-50,-70-260 Pure polytef adhesive tape: made of superior pure PTFE (polytef). Thickness(mm),width(mm),length (mm),Temperature(ºC) 0.08,10-400,10-50,-70-230 0.13,10-400,10-50,-70-230 0.18,10-400,10-50,-70-230 0.25,10-400,10-50,-70-230
Adhesive, tape.
Adhesive tape, BOPP packing tape, bopp jumbo roll.
1) Packing tape is made with BOPP film and coated with special water based acrylic adhesive. 2) The range of usage is sealing and packing carton box,and it is also suitable for super market sales. 3) It has the advantages of high resistant and tensile strength, light, high adhesion and printable. 4) It could be made for different color and printed your logo. Inquiry is welcomed. You surely will receive our reply in due time. Thank you.
1) It's made with tissue paper as the backing material. As the double sided terms implies, the tapes use solvent based, water based, hot melt based adhesive to coat both sides of backing material. They are then pressed on to release paper for separation purposes. 2) It's characterized by excellent thickness, easy tear and good adhesion, suitable for decoration, sealing documents, postal service and shoe making industry. 3) Best choice for the office, home and school.
Tpu elastic tapes, usually specification: 03*0.12mm, 04*0.12mm, 05*0.12mm, 06*0.12mm. Approximate length /kg tolerance:+-3%( any specification can be made by ordered ) 1kg/bag, 20kg/carton
1) Masking tape is made from crepe paper as the backing material which is coated with ruber based adhesive. The adhesive is formulated so that it leaves no traces after removing the tape. 2) It is Widely applied to household and industry for bunding, sealing, holding surface protection. 3)It can also protect egdes of mirror or glass against hurting people. 4) The temperature can be 60 degree, 80 degree, 120 degree. So you can choose the right temperature of masking tape according to your needs.
We can provide the semi products, Jumbo rolls with good quality and reasonable price. Inquiry is welcomed. You surely will receive our reply on due time. Thank you.
masking tape is made with high quality natural rubber adhesive (water based,or solvent based)and crepe paper for good performance and different application,From low to high temperature for industrial or home usage; and specially- formulated adhesive to be use on fragile surfaces or outdoor to withstand exposure to UV for up to 21 days after application is also available. Paint masking for metal,rubber and plastic.Also ideal for indoor paint masking,light packaging,holding ,binding and drafting.Wood and general purpose. High temperature professional industrial garde, for automotive painting and oven baking application, application, appliance and electrical industrial, semiconductor protection.P.C Board which needed higher temperature resistance
The product is made of polyethylene and gauze, and the finished product is made into a substrate. The plastic surface is coated with a release agent, and the yarn surface is coated with a hot melt pressure sensitive adhesive. Used for packaging, binding, sealing, repairing, binding books, stage sets, exhibition exhibitions, carpet seams,
Adhesive tape .Exporting
Features: 1, This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, natural stone material 2, The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3, Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4, Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5, Good anti-infiltration function 6, No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1, The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2, For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation process: 1, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2, Push the ceramic tile or heavy type ceramic tile above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material 4, Can be used for the old ceramic tile re-tread. Cautions: 1, Never mix the dry slurry with water and use again 2, For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3, For the painting surface, make sure the initial bond strength and no flake 4, Operating under 5¡æ~40¡æ situation 5, Clean the surface by little wet sponge or cloth before it dry 6, Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount) Technical reference using 3*3mm tooth scraper about 1.7kg/m2 1, adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) using 6*6mm tooth scraper about 3.0kg/m2 2, cool time: about 10min (cool time: the longest cool time that the adhesive can last ) using 10*10mm tooth scraper about 4.5kg/m2 3, dry time: 24h (according to the weather) 4, water resistance: excellent; non-toxic, prevent fire the smoother the surface, the less amount 5, when dry, anti-weak acid, anti-strong alkali and oil resistance 6, cut degree: £¾1.2MPa (14days later). Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
1.Backing material: bopp film 2.Adhesive: acrylic 3.Adhesive type: water based acrylic 4.Initially stick force ( # ) ¡ý 12; 5.Peel strength ( n/25mm ) ¡ý 6; 6.Holding force ( h ) ¡ý 24; 7.Tensile strength ( mpa ) ¡ý 120. 8.Thickness: 35-90mic 9.Width: 12-150mm 10.Length: 10-1500m (1)individually wrapped, shrink, carton. (2)6rolls/shrink, about 36~100rolls/carton(according to different specifications) (3)carton meas: any carton size as your request
Our Company Offer Good Quality Of Hot Melt Adhesive Include Glass Transparent And Normal Adhesive. Item Color Low Tempreture Light Yellow, White, Brown 130-150.C Middle Tempreture Light Grey, White, Brown, Light Yellow 150-180.C High Tempreture White , Brown, Light Yellow, Grey White 180-210.C
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: bricks for wall using 3*3mm tooth scraper or 6*6mm tooth scraper, bricks for floor using 6*6mm tooth scraper or 10*10mm tooth scraper. Cautions: 1, Make sure the smooth and vertical rate of the surface before operation 2, Never mix the dry slurry with water and use again 3, For the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1, This product is a new type strong stone adhesive, applied to all kinds of low water absorption stone materials like large-scale artificial stones, culture stones, and natural stones 2, No need to wet the brick wall, effectively improve the efficiency 3, Strong bond ability, material-reducing, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the quantity of the wall 4, Good anti-acid and anti-alkali and anti-infiltration and anti-aging function 5, Small shrinking rate, no cracking, can be used in cold and humid environment. Application: 1, The adhesive for cement plaster, brick, smooth cement wall paste stone 2, The adhesive for low water absorption surface and light steel frame system board, like gypsum board and Eight board. Surface Treatment: The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. Operation Process: 1, The ratio: MB tough stone adhesive: water: 3.3: 1 (25kg powder, about 7.5kg water) mixed and stirred into paste, using an electric mixer to make particle paste, put it aside for a few minutes and then a little stirring to gain the better effect 2, Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2, then push the stone above it 3, For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Normal Amount: Coverage areas differ according to the circumstance: 1, using 3*3mm tooth scraper about 1.8kg/m2 2, using 6*6mm tooth scraper about 3kg/m2 3, using 10*10mm tooth scraper about 4.8kg/m2 Note: the amount is related to the smooth, vertical rate, and thickness of the stone material Cautions: 1, make sure the smooth and vertical rate of the surface before operation 2, never mix the dry slurry with water and use again 3, for the painting surface, make sure the initial bond strength and no flake 4, Finishing after 24h can be walked in or fill the crack. Store Method: Store in cool and dry place, unopened product can be saved for one year. 25kg/bag
Features: 1. This product is a new type strong adhesive, applied to indoor and outdoor wall paste of large-scale ceramic tile, grassing stone, and natural stone material 2. The indoor ceramic tile adhesive of light steel frame system board, like gypsum board and Eight board 3. Can be used on the low water absorption surface, like paste new ceramic tile above the old ones, and can be used on the firm painting surface 4. Excellent flexibility, can bear the bonding layer stretch that caused by temperature 5. Good anti-infiltration function 6. No need to wet the brick wall, effectively improve the efficiency. Surface Treatment: 1. The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials. 2. For the new wall, when finding the leveling layer of cement mortar, plaster, should improve the leveling layer of mortar label the cohesive force of the wall, or mix MB-03 slurry additive. Specific reference, please look at the MB-03 introduction. Operation Process: 1. Using tooth scraper to scrap the adhesive onto the surface evenly, control within 1m2 2. Push the ceramic tile or heavy type ceramic tile above it 3. For the ceramic tile with deep ditch or stone material, expect for the surface, scrap the backside of the tile or the stone material. Cautions: 1. Never mix the dry slurry with water and use again 2. For the light wall board install large-scale decorative panels, like gypsum board and Eight board, confirm the wall firmness before operation 3.For the painting surface, make sure the initial bond strength and no flake 4.Operating under 5¡æ~40¡æ situation 5.Clean the surface by little wet sponge or cloth before it dry 6.Leave 1.5mm joint space between two tiles, suggesting MB-MC color anti-moldy gap filler. Technical Reference: Coverage area(amount). using 3*3mm tooth scraper about 1.7kg/m2. using 6*6mm tooth scraper about 3.0kg/m2. using 10*10mm tooth scraper about 4.5kg/m2. Technical reference: 1, Adjust time: about 15min (adjust time: the effective time for the dislocation to adjust) 2, Cool time: about 10min (cool time: the longest cool time that the adhesive can last ) 3, Dry time: 24h (according to the weather) 4, Water resistance: excellent; non-toxic, prevent firethe smoother the surface, the less amount 5, When dry, anti-weak acid, anti-strong alkali and oil resistance 6, Cut degree: £¾1.2MPa (14days later). Store Method:Store in cool and dry place, unopened product can be saved for one year. 25kg/bag.
Bopp jumbo roll, Bopp packing tape, adhesive tape, masking tape, duoble sided tape, kraft paper tape, PVC insulation tape.
Double sided tissue tape are made from non woven-tissue paper coated on both sides with acrylic adhesive or hot melt or solvent adhesive and laminated with release paper. is recommended for mounting light objects and may be used to mounting,decorating,holding and joining of light weight objects Double sided EVA foam tape is made of EVA as backing material which double coated with a pressure sensitive acrylic adhesive of excellent adhesion and PE-coated paper as release liner.
