The SF6 insulated switchgear is suitable for middle voltage power distribution system with a rated voltage of 12kV. It could be used as RMUs in a power supply network, fault isolating switches and sectionalizing switches. If equipped with distribution automation devices (FTU/DTU) and communication devices, the SF6 insulated switchgear could communicate with the control center, measure the cable voltage, current, etc, and monitor the working status of switches. BKRM6- 40.5 series of ring main unit is SF6 gas- insulated metal common tank enclosed switchgear, consisting of load break switch unit, load break switch fuse combination electrical unit, vacuum circuit breaker unit, and the incoming line unit of bus. It adopts a range of advanced technologies and materials, with excellent electrical and mechanical properties, less affected by environment and climate, in small size, easy to install easy to operate, with no need of maintenance, and can be flexibly combined. Its clear and intuitive design ensures simple and direct operation, the feeder's connection capacity is large, suitable for a variety of wiring systems. Besides,we can replace the SF6 gas with nitrogen(N2 gas) that it will become a environment protection green gas insulated switchgear. The green gas insulated switchgear safer and environmentally friendly more than SF6 GIS and it will replacing SF6 GIS in the future.
KYN28-12 removable AC metal-clad switchgear (short for panel as below) is a new product. It will be a substitute for old fashioned metal-enclosed switchgear, such as KYN-12, JYN-12, GFC-12, etc. The panel applies to 3.6~12kV 3 phase AC 50Hz network for receiving and distributing power energy and also for control, monitor and protection. It accords with standard of IEC62271-200, IEC60694, GB3906. The newly introduced and developed large current and high breaking switchgear can also be used as a high- voltage generator export.
1.Description Chase friction testing machine is used to evaluate the frictional characteristics of material in braking system in accordance with the SAE J661,GB 5763-2018 and GB/T 17469-2012. Chase machine is suitable for small bench test of M1, M2, N1, O1 and O2 vehicles brake linings. This machine is widely used for product formulation R&D, Quality control and Certification etc. 2.Principle A constant pressure is applied to the sample,which will be pressed against the inner surface of the friction drum which rotates at a certain speed, so a friction force will be generated along the tangent direction of the contact surface. The friction coefficient of the tested sample can be determined by measuring the pressure and friction force. During the test, the Chase friction tester controls the temperature change at any time according to the requirements. The drum outer ring is used to assist the heating tube heating and the back suction cooling, so that the temperature change at the sample is stable and the temperature measurement accuracy is higher. 3.Features (1)Loading by Pneumatic servo with high precision control. (2)Temperature of friction drum is adjustable to adapt to different test requirements and different climatic condition. (3)Rubbing speed can be set freely between 0 and 1000 RPM. (4)The maximum load is up to 2000N. (5)This machine is controlled by PC. Speed, loads, temperature and test time can be preset by software. Test results are saved in computer. 4.Standards SAE J661, SAE J866, GB 5763-2018, GB/T 17469-2012, 5.Specifications Speed 0 to 1000 RPM Load 0 to 2000 N Temperature 0-600 (1112) Heating power 6KW Friction drum Ф277mm Power AC 380V Weight Approximate 2100kg
1. Size of concrete specimens for compression strength test Concrete cubic specimen: 150X150X150mm, 100X100X100mm, 200X200X200mm Cylindrical concrete specimen: diameter 150X300mm, diameter 100X200mm, diameter 200X400mm 2. Brief introduction of concrete compressive strength test procedure 1) Placing the concrete specimen---place the test specimen on the lower bearing block. Carefully align the axis of the specimen with the center of thrust of the spherically seated block. 2) Apply the load continuously and without shock until the specimen fails and record the maximum load carried by the concrete specimen during the test. Note the type of failure and the appearance of the concrete. 3.Relative test method GB/T 50081 standard for test method of mechanical properties on ordinary concrete ASTM C39 standard test method for compressive strength of cylindrical concrete ASTM E74 practice of calibration of force-measuring instruments for verifying the force indication of testing machine 4. Specifications for concrete compressive strength testing machine Max. capacity: 3000KN( lower or higher capacity can make to order) Grade of testing machine: grade 1 Distance between upper and lower compression platen: 320mm Stroke of piston:50mm Size of upper and lower compression platen:375X375mm Weight :about 900kg
1. Introduction and test principle of compression strength measuring The compression testing machine is to measure compression strength of corrugated boxes in the situation of pressure and protect functions of packages for the objects filled in the packages. Test principle: (1) Corrugated boxes compression strength test, loading to the corrugated boxes using a compression testing machine at a certain constant rate untill corrugated boxes are broken or till certain load or displacement are reached. (2) Corrugated boxes stacking test, loading a certain force to the corrugated box using a compression testing machine untill corrugated box is broken or sustain a certain time period. When measuring deformation of corrugated box during compression test, an original load should be set as a datum point. The datum point can refer to the following chart: Average compression force(N)Original force(N) 101-200 10 201-1000 25 1001-2000 100 2001-10000 250 10001-20000 1000 200001-100000 2500 2. Functions of compression testing machine This machine is applicable to metal, cementing compound, tubes, sectional bars, aerospace, petrochemical, waterproof rolls, wire and cable, textile, fiber, rubber, ceramics, food, mechanical packaging, geo-textile, film, wood, paper and other industries and quality supervision department, and it also can be used in college for teaching demonstration. 3. Specification of compression testing machine 1 Max. Load 20KN 2 Resolution of test force 1/300000 3 Resolution of displacement 0.001mm 4 Precision of crossbeam displacement 0.5% 5 Precision of deformation 0.5% 6 Measuring range of test force 1%-100%FS 7 Relative error of test force 1% 8 Relative error at zero point 0.5% 9 Speed of crossbeam 0.01-500mm/min 10 Precision of crossbeam speed 1% 11 Speed range of load 0.005%-5%FS/s 12 Precision of load speed When speed is less than 0.05FS/s, precision is within 1% of set value, when speed is more than 0.05FS/S, precision is within 0.5% of set value 13 Speed of deformation 0.005%-5%FS/s 14 Precision of deformation speed When speed is less than 0.05FS/s, precision is within 1% of set value, when speed is more than 0.05FS/S, precision is within 0.5% of set value 15 Stroke of crossbeam 900mm 16 Effective tensile height 650mm 17 Effective test span 400mm 18 Effective compression height 800mm 19 Diameter of compression platen 100mm 20 Voltage and power 220V,50Hz, 700W 21 Dimension of main machine 650X450X1650mm 22 Weight of main machine about 300kg
High voltage distribution switchgear 1) general A complete set of indoor equipment of a single bus bar or double bus bars segmented system rated at 3kvto 12 kv in voltage and 50 hz in frequency. It has the functions of receiving & distribution power, and controlling, protecting and measuring circuit 2) advantage 1:anti-corrosion cabinet, can be used in complex working condition2:intelligence and easy control 3:multi protection function 4:easy operation and maintenance 5:removable and full closed
1.Model:WDW-100 2.Product name:computerized electrical universal testing machine 3. Applications of testing machine This machine is applicable to metal, cementing compound, tubes, sectional bars, aerospace, petrochemical, waterproof rolls, wire and cable, textile, fiber, rubber, ceramics, food, mechanical packaging, geo-textile, film, wood, paper and other industries and quality supervision department, and it also can be used in college for teaching demonstration. 4. Features of testing machine 1) Adopting aluminum alloy cover, with attractive streamline structure 2) Mainly used to test mechanical properties for metal, non-metal and composite materials 3) Adopting precision auto control and data acquisition system to realize fully digital adjustment to data acquisition and control process. During test, it can test max. Bearing tensile force, compression force, tensile strength, deformation, elongation, yield point and other technical specifications 4) After test, the above parameters can be calculated automatically through main controller according to the test parameters, which are set before test and meantime display the corresponding test results. All test parameters can be saved and inquired after test, also can be printed out. 5) With remote control box to realize speed adjustment of crossbeam, flexibly and freely switched 6) With functions of automatic return to original position, intelligently, efficiently, quickly 7) With limit position function of any working position and over voltage, over current protection functions, reliable and safe 8) With many control modes of constant speed control to force, stress, deformation, strain and low cycle and user self-programming control 9) Switch among many test curves: stress-strain curve, load-deformation curve, load-displacement curve, load-time curve, deformation-time curve, displacement-time curve. Partial enlargement, overlap and comparison. 5.Spec. of testing machine
Lan cable, optic fiber cable, power cable, other chemical.
Heater for low woltage switchgears DRJ100 100W YOYIK has laid out the market with a global vision and established a wide network of power station spare parts sales and service in China to ensure that it can quickly respond to the needs of global customers. The company's products are exported to many countries and regions. By providing products and services with international standards, YOYIK has established a good brand image in the international market. Yoyik can offer many spare parts for power plants as below: #DF-Heater for low woltage switchgears DRJ100 100W-DF proximity sensor rpm measurement CWY-DO-812506 LVDT sensor TDZ-FRD-301 Air Pressure Regulator 67CFR-225/SB Pressure Switch 52RN-KK116-M1-C2A-XX618 Turbidimeter LPV417.99.00002 Middle Relay JZX-22F positioner DVC2000 NEPM meter KV type b thermocouple WREK2-331 Limit Switch ( SOLDO SX01200-10U77A3 Rotor Position proximity Probe ES-11-M14x15-B-00-05-10 Camera IST-M938SRZ 900TV High energy igniter DKGP-20 Sensor for measuring H2 purity KQL1500 Electric actuator SND-Z30-24S Bolt electric heating rod ZJ-20-T1(R) Limit Switch D4A-4501N cam bien ap luc truoc luoi chan rac 9NN-EE45-M4-C1A-X371 Digital Temperature Monitor LWK-Z3T8(TH) lvdt position transmitter DET500B Bolt electric heating rod ZJ-22-52 Signal modules â?? analog 6ES7232-4HD32-0XB0 dc pressure switch RC861CZ097HSSYMA59 Glass window components TC-SMW-16-5 FLAME IMAGE MONITOR CAMERA LHJTT-II-2EG Controller for H2 purity analysers DC3500-CE-0Y00-200-10000-00-0 MDC module MDC 100A-1600V Power free oil inlet automatic circuit breaker RN1UBQ01-HKXS Differential Pressure Switch 2 4NN-K5-M4-CIA LVDT transmitter XCBSQ-04/200-02-11 Eddy Current Sensor PR6426/000-001 Displacement Transducer TD-1 100S speed sensor DF6202-005-050-04-01-01-000 circuit board ME8.530.004 Acoustic conduit DZXL-VI-J Rotor Position proximity Sensor Extension Cable ESY-80 Heater for low woltage switchgears DRJ100 100W MY-DFYL-2024-10-11
Impact specimen gap hydraulic broaching machine is the only instrument gap for processing the qualified sample except the optical curve grinding machine. Because of processing theory once, the identity of processing the gap is very nice. This broaching machine adopts w18cr4v manufacturing, high hardness, wear resistance, and every tool can process the sample as many as 20, 000.
Electromagnetic Flowmeter explosion-proof electromagnetic flowmeter intelligent electromagnetic flowmeter Product code: 145538-152 Update time: 2015.08.25 Views: 1304 Processing custom origin: In kaifeng Type: Type flow meter SKLD series Measuring range: 2000 (m3 / h) Level of accuracy: 0.5 Nominal diameter: DN3-3000 (mm) Working pressure: 0.6 ~ 4 (MPa) Working temperature: - 10 ~ 150 Product Overview SKLD type electromagnetic flowmeter is the intelligent electromagnetic with research and development, which adopts domestic and foreign adva nced technology. Electromagnetic transducer with high-speed central processing unit (CPU) and the features of rapid computing speed and high precision, reliable performance measurement are in both Chinese and English menu.Electromagnetic Flowmeter is divided into one type of electromagnetic flowmeter and split electromagnetic flowmeter,Insert electromagnetic flowmeter. Electromagnetic flowmeter can be divided according to the use of function:liquid flow meter,water flow meter,sewage flow meter,Intelligent electromagnetic flowmeter,explosion-proof flow meter,irrigation flow meter,mud flow meter Sensor uses non-uniform magnetic field technology and special magnetic circuit structure. Magnetic field is stable and reliable, and the circuit structure reduces the volume, The sensor can reflect the traffic change timely and effectively, and have a stable value of measuring water, sewage, slurry, pulp, acid, alkali, salt slurry liquid and food, etc. There are lots of wide applications in the petroleum chemical industry, metallurgy, coal, water conservancy project of water supply and drainage, sewage treatment etc. The electromagnetic flowmeter has two types: the compact and the sensor for remote transmitter. Product Features In-line unimpeded flow components, measurement of almost no loss of pressure, low straight pipe requirements Measurement results and the velocity distribution, fluid pressure, temperature, density, viscosity and other physical parameters Blank-pipe measurement function without additional electrode, continuous measurement, the fixed value alarm Velocity measuring range: 0.1-15 m/s, velocity resolution: 0.5 mm/SEC Low frequency square wave excitation and excitation frequency: 1/16, 1/20, 1/25 power frequency power frequency power frequency High frequency square wave excitation and excitation frequency: 1/2 power frequency (applicable to size measurement) (optional) Explosion-proof instrument can be used for the corresponding explosion-proof occasions
Turbine flowmeter compressed air flowmeter gas flowmeter Product name: turbine flowmeter Product code: 164912-752 Update time: 2015.08.25 Views: 346 Processing custom origin: in kaifeng Type: type flow meter LWG series Type: impeller type flowmeter Measuring range: 0.4-20000 (m3 / h) Level of accuracy: + / - 1.5% Nominal size: 10-500 (mm) Working pressure: 2.5, 6.3, 16 Working temperature: - 20 ~ 55 Summary: Turbine flowmeter can be divided according to function name gas flow meter,flue gas meter,steam flow meter,gas flow meter,compressed air flow meter,liquid flow meter. LWG type turbine flow sensor and receiving electrical signals of the display instrument of Turbine flowmeter, which is used to measure low and medium viscosity closed pipes Degree of fluid (liquid or gas), the total volume flow and in petroleum, chemical industry, metallurgy, aviation and scientific research departments for a wide range of applications. Sensor is composed of turbine sensor components and amplifier, the structure of the two together for one-piece: to measure the structure of the positive and negative flow For two-way type; With inserted rod can be installed in the large diameter pipe flow body flow structure for a plug-in. Based on the principle of moment balance sensor work. When the fluid flows through the sensor, promote the impeller rotation, when the flow rate must be dynamic torque Maintain and drag torque balance, the impeller speed. Evenly distributed on the permeability of the impeller blade with the impeller rotation, to periodically change detection The reluctance of the magnetic field sensor (coil), electrical pulse signal detector, after the amplifier amplification output. The output electric pulse frequency and impeller speed Is proportional to the impeller speed is proportional to the flow in, so the output electric pulse frequency is proportional to the flow sensor flow, 4-20 ma signal is converted is proportional to the flow. Features: 1) impurity resistance is strong, tangential impeller rotating at can release floating debris in the fluid at any time, when the winding on tangential impeller blades. 2) resistance to electromagnetic interference and strong vibration resistance. 3) the structure and principle of the sensor and display instrument is very simple, user especially easy to master its use and maintenance technology. 4) after replacement of impeller and bearing, meter coefficient is constant. 5) wide flow range, lower limit velocity is low. 6) complete sets of flow meter for the measurement of the fluid volume error is small. 7) almost no pressure loss, save power consumption. 8) sensor can be installed in open air, the sensor can be submerged in the water use for a long time. 9) have a globe valve sensor, install and remove all don't need to stop. 10) horizontal, vertical, inclined pipe can be used. 11) complete sets of flowmeter the purchase, installation, and low cost.
Ring chamber orifice meter ring chamber orifice meter manufacturer Product name: Ring chamber orifice meter Product code: 151116-813 Update time: 2015.08.25 Views: 860 Processing custom origin: in kaifeng Type: type throttling device LWG Type: volumetric flowmeter Measuring range: 0-100 (m3 / h) Level of accuracy: + / - 1.0% Nominal size: (DN50- DN2600 (mm) Job stress: 40 or less (MPa) Working temperature: 70 ) Summary: throttling device, also known as differential pressure flowmeter, Orifice flowmeter contains (integrated orifice flow meter, standard orifice, annular orifice flow meter, integrated annular orifice flow meter) Ring chamber orifice meter can be divided according to function name gas flow meter, flue gas meter, steam flow meter, gas flow meter, compressed air flow meter, liquid flow meter. LWG type series annular orifice meter is SIKE measurement and control technology co., LTD., henan overview on the research and development on the basis of the standard orifice throttling flow sensor, because it USES annular single structure, make measurements in all kinds of dirt medium through the orifice plate with a circular seam between pipe can easily pass. So the circular orifice flowmeter is widely applied in the dirt medium flow measurement. Circular orifice itself comes with a measuring tube. In central measuring tube fixed a concentric circular plate - flow plate, the plate of the bearing steel in the mouth (10) and take pressure staggered, so bearing steel downstream of the flow of the fluid resistance is negligible, and the upstream flow plate without any block, can make the upstream velocity distribution axisymmetric completely, is advantageous to the geometric similarity and dynamic similarity, improve the accuracy of measurement. Circular orifice meter is suitable for various fluid (gas, steam, liquid medium, such as: saturated steam and superheated steam, compressed air, all kinds of exhaust gas, burning furnace, cooling water, heavy oil, residual oil, fuel oil, condensate, all kinds of corrosive chemical solution, etc. Features: 1, not only can measure the general fluid flow, and can also be applied to contain various impurities such as dust, suspension, precipitation, etc.) of the fluid, such as a variety of hot gas, flue gas, natural gas, cooling circulating water, etc. 2, measuring saturated steam superheat steam can avoid stop steam condensate accumulation formation, when steam again to send, can quickly into the accurate measurement. 3, instrument ontology has a straight measuring tube, on-site installation, the installation error (such as eccentric, sealing gasket into pipe) has no effect on meter almost.
1. The test angle is based on national standards gb4706.1-2005 (iec60335-1: 2004) chapter 11, " fever " in the design and manufacture of test requirements. 2.The test angle is mainly used for a variety of electrical, temperature testing provides electrical products meet the standard requirements of environmental conditions temperature test. The actual test sample can be customized with different distribution specifications, test angle number and dimensions of the measurement points.
The spray tester ipx 3/4 is a hand-held test device to verify protection against spraying and splashing water. The water pressure can be adjusted using the flow control knob on the device to give the required flow rate. The pressure can be seen on the gauge which is convenient positioned by the spray tester ipx 3/4. The spray pattern of the nozzle is made to the specifications of ie60529. The removable shield feature make it easy to test without the interference of the shield.
It is used to evaluate the resistance tracking performance of solid insulating material surface under the combined influence of electric field and humid or contaminate medium. Sum up,it is used to measure the compare tracking index (CTI) and electrical resistance index (PTI).
Features: 1. Material: Alloy Steel, Carbon Steel, Stainless Steel, , Cast Iron, Aluminum, Copper, Brass and so on 2. Heat Treatment: Hardening and Tempering, High Frequency Quenching, Carburizing Quenching and so on. 3. Surface Treatment: Galvanizing/Zinc Plating, chrome plated, Black oxide Treatment, Spray Paint, Mirror Finish, Sand-blasting and so on according to ROHS demand. 4. Inspection: All items are checked and tested thoroughly during every working procedure and after the product is finally manufactured to ensure that the best quality product enter into the market. 5. Durable, bad condition Resistance Our sprocket models for your reference: 1)Short/single pitch sprocket: *Chain matched:35 (06C) Teeth:from 9-120 *Chain matched:40 (08A) Teeth:from 9-120 *Chain matched:50(10A) Teeth:from 9-120 *Chain matched:60 (12A) Teeth:from 9-120 *Chain matched:80 (16A) Teeth:from 9-120 *Chain matched:100 (20A) Teeth:from 9-120 *Chain matched:120 (24A) Teeth:from 9-120 *Chain matched:140(28A) Teeth:from 9-120 *Chain matched:160 (32A) Teeth:from 9-120 *Chain matched:180 (36A) Teeth:from 9-120 *Chain matched:200 (40A) Teeth:from 9-120 2)Double pitch sprocket: *P=25.4mm Teeth:from 7-100 *P=31.8mm Teeth:from 7-100 *P=38.1mm Teeth:from 7-100 *P=50.8mm Teeth:from 7-100 *P=63.5mm Teeth:from 7-100 Packing: Little quantity (Samples ) Carton More quantity: Wooden case Delivery time: standard size  within 10 days.                custom-made size within 15 days. ServiceOEM/ODM
Product details Product Specification Measures from 0-9990ppm Accuracy:+-2%, Battery: 2x1.5V(Button Cell) Size:155x31x23mm(6.1X1.2x0.9in) Use the TDS Meter to: Check the performance of your water filter Check for the hardness (1 grain=17ppm) Make sure you always drink pure water. Features Hold function saves the measurements for convenient reading and recording. Auto-off function:turns off meter after 10 minutes of non-use to conserve batteries. Dual Range: Measures from 0-999ppm,with a resolution of 1 ppm. From 1000 to 9990ppm,the resolution is 10ppm, indicated by drinking x 10 symbol,Factory calibrated. Advantages: Taking Temperature Measurement 1.Once the meter is on,the temperature function can be used at any time, in or out of liquid. 2.Press the TEMP button.The display will switch to temperature(in Celsius only). 3.To return to TDS mode,press the TEMP button. Precaution and notes Do not drop the entire TDS meter in water or dip beyond the maximum immersion level.This unit is not covered under the warranty if water enters the unit. 2. Do not store the TDS meter under high temperature or direct sunlight.This will shorten the life-span of the product and potentially avoid the warranty. 3. The TDS-3 meter is calibrated at 642ppm. It is recommended that the calibration level should be the similar to the sample to be tested.If you are testing higher ppm(member,water quality association). Calibration Your meter has been factory calibrated well. warranty 1.Three year warranty: The product is warranted to the purchaser against material and workmanship for three(3) years from date of purchase. What is covered: Parts and labor , or replacement at the companyâ??s option. Transportation charges to the purchaser. What is not covered: Transportation charges to the company. Damages from the abuse or improper maintenance (see operating instructions and precautions). Any other consequential damages, incidental damages ,or incidental expenses,including damages to the property.Some states do not allow exclusive or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. FAQ Question 1: What is the MOQ of this item ? Answer: The item MOQ is 5000pcs. Question 2: How to pack this item? Answer: Box packing is our usual practice, you can also send us your packing design, and we can packing as your requirement. Question 3: How to make payment? Answer: You can make payment by T/T,Paypal.Western Union and of course cash face to face at our factory. Question 4: What is the lead time? Answer: Our lead time is within 10 days after receive your payment based on MOQ:5000PCS. Question 5: Can you accept OEM & ODM? Answer: Yes, we can accept OEM &ODM -
Digital Electronic Tension Meter (DTM-501) for Yarn Copper Wire Fibre DTM Series Digital Tension Meter Tension measuring 128 * 64 LCD display, late-model design, comfor table handfeel , easy operation, measure the value of direct display tension, maximum, minimum, and can store records of measurements to determine the quality control of the actual tension values. It can be widely used in wire, strip processing time of tension measurements (such as: yarn, steel wire, copper wire, copper strip, tape, film, fiber-optic cable, carbon fiber lines, etc.).
Digital Electronic Tension Meter (DTM-501) for Yarn Copper Wire Fibre DTM Series Digital Tension Meter Tension measuring 128 * 64 LCD display, late-model design, comfor table handfeel , easy operation, measure the value of direct display tension, maximum, minimum, and can store records of measurements to determine the quality control of the actual tension values. It can be widely used in wire, strip processing time of tension measurements (such as: yarn, steel wire, copper wire, copper strip, tape, film, fiber-optic cable, carbon fiber lines, etc.).
