High alumina castable is a refractory castable made of high alumina raw material with binder and aggregate in traditional ratio.On the basis of the preparation of high strength and high aluminum castable, the granule gradation is adjusted, different admixtures are added, cement dosage is reduced, performance is improved, medium temperature strength and softening temperature under load are increased, thermal conductivity is reduced, and thermal stability is good.The furnace body structure integrity is strong, the air tightness is better than the brick furnace, extends the furnace life, saves the furnace repair cost, the economic benefit is remarkable as the high aluminum refractory castable characteristic.
The improvement of the performance of low cement casting material is actually the application of micro powder technology. There is a gap between the stability of low cement castable and that of laboratory castable.Low cement castable easy to occur problems are: 1, poor construction performance, poor liquidity;2. The hardening speed varies greatly, and there is quick setting or non-setting;3, easy to burst in baking;4. Abscission occurs;5. Low strength and poor wear resistance.These are caused by refractory castable products abnormal damage and other quality problems. Low cement refractory castable itself in addition to wear resistance, refractory aggregate, is used with good raw materials fine powder and ultrafine powder, cement and admixture, etc., through adjusting the proportion of each component, improve the high temperature performance of castable, thereby improve the strength of refractory castable. Low cement castable key construction, should pay attention to is: (1) do not arbitrarily increase the water content of refractory castable, (2) mold support set too high, leading to castable water content is too large and vibration compaction;(3) No mold shall be set during lining construction of feeding pipe, and castable material shall be manually daubed;(4) In order to save the mold, the maintenance is less than 48 h to remove the mold, resulting in the casting cracking or internal damage;(5) The material, shape, size, welding quality, quantity, anti-expansion treatment and unreasonable expansion joints of the anchoring parts;Do not follow the operational sequence of dry stirring, wet stirring and feeding, directly mix the dry and wet materials, resulting in the castable is not fully mixed evenly, part of the material is not wetted by water, making the castable has no strength. There are also key water issues, to use tap water, to avoid the introduction of acid and base impurities, gradually add, in order to make the dispersant in the powder to play a full role.Excessive water addition will directly lead to a significant decline in the strength of refractory castable construction, and in the field construction the water addition tends to exceed the degree of artesification.The pouring body itself is easy to appear when the ambient temperature rises rapidly, the baking burst, resulting in large area of damage.Once the temperature of the castable itself is below 5 the castable will still have no strength even after curing for 24 hours.The construction and maintenance shall be carried out in strict accordance with the 48-hour mold removal mechanism. In dry areas, water and wet maintenance shall be carried out; in cold areas, airtight heating maintenance shall be realized within 48-hour maintenance to ensure the maintenance temperature. In a word, if the above points can be achieved step by step in accordance with the requirements, it will certainly improve the performance of low cement casting.
Steel fiber has good tensile strength, strong grip strength and high hardness.If steel fiber is mixed in castable, the steel fiber castable products produced by this method are not only used, wear resistant, tensile and compressive, but also have a good anti-theft effect.And its adaptability and operational planning will be wider.It can be used at different temperatures.Greatly improved product utilization rate.So now large kilns, melting furnaces and so on will mostly choose steel fiber castable.Is to travel the quality of the product and use of life, compared to down, such a product more affordable. Steel fiber castable can reduce the shrinkage of castable during curing, grilling and high-temperature use. After adding steel fiber, not only the toughness of castable can be improved, but also the impact and mechanical strength of the machine can be improved.After adding steel fiber, the thermal shock performance of castable is improved.The steel fiber castable prevents fracture or spalling by preventing microcrack and mechanical stress. Steel fiber castable is widely used in high temperature vulnerable parts of metallurgy, building materials and circulating fluidized bed boilers.As follows: according to the classification of the material, it is suitable for planning the corundum quality before and after the steel fiber reinforced castable first used in large cement kiln kiln and other industrial kiln lining, high aluminum and corundum mullite stone steel fiber reinforced refractory castable first used in the cement kiln kiln mouth, wicket cover, before and after cooling machine in high temperature resistant parts and other industrial kiln liner.
Steel fiber has good tensile strength, strong grip strength and high hardness.If steel fiber is mixed in castable, the steel fiber castable products produced by this method are not only used, wear resistant, tensile and compressive, but also have a good anti-theft effect.And its adaptability and operational planning will be wider.It can be used at different temperatures.Greatly improved product utilization rate.So now large kilns, melting furnaces and so on will mostly choose steel fiber castable.Is to travel the quality of the product and use of life, compared to down, such a product more affordable. Steel fiber castable can reduce the shrinkage of castable during curing, grilling and high-temperature use. After adding steel fiber, not only the toughness of castable can be improved, but also the impact and mechanical strength of the machine can be improved.After adding steel fiber, the thermal shock performance of castable is improved.The steel fiber castable prevents fracture or spalling by preventing microcrack and mechanical stress. Steel fiber castable is widely used in high temperature vulnerable parts of metallurgy, building materials and circulating fluidized bed boilers.As follows: according to the classification of the material, it is suitable for planning the corundum quality before and after the steel fiber reinforced castable first used in large cement kiln kiln and other industrial kiln lining, high aluminum and corundum mullite stone steel fiber reinforced refractory castable first used in the cement kiln kiln mouth, wicket cover, before and after cooling machine in high temperature resistant parts and other industrial kiln liner.
*opening doorï¼?90 degreee bending treatment as bottom pictures shown. *openingï¼?Ul certificed electric lock opening *Door gate: with 40mm fireproof plate --Thichness of wall: 60 mm --Fireproof time: 2 hours in factorys testing. *SS. plate decoration *Optional colorï¼?blackï¼?grey. *Inner spare paratsï¼?one blanket bolt for fireproof. Lock structuresï¼?three way pullingï¼?bolt of World lock . *openg angle: 183 degree.
Excellent thermal resistance Fireproof Rock Wool Board Rock Wool Insulation products are made from natural mineral wool such as basalt and dolomite. Density Thickness kg/m3 mm 60 50 70 80 100 150 / 75 50 70 80 100 150 / 80 50 70 80 100 150 / 100 50 70 80 100 150 / 120 30 40 50 80 100 / 130 30 40 50 70 80 100 150 30 40 50 70 80 100 180 30 40 50 70 80 100 200 30 40 50 70 80 100 PRODUCT FEATURES Rock Wool Board products are made from natural mineral wool such as basalt and dolomite. The natural rock are melted into melts in cupola at a very high temperature about 1500. The highest application temperature is 650. it has characters: heat insulation sound reduction, fireproof, waterproof and so on. Fire Doors Rock Wool Board advantages: - Excellent thermal resistance - Non-flammable - Easy to install - High sound absorption material - Easy handling and installation - Attractive aluminum appearance - Water-repellant - Resistant to ageing - Marine certified Application of Rock Wool Board: 1. Used for fire protection, thermal insulation in construction and building, commercial and residential buildings. 2. Used for sound absorption in roofing, celling, external wall, partition wall and floating floor. 3. Low density Environment Friendly Rock Wool Board suitable for roof and wall in the building Properties Value Density 60-150 Kg/m3 Shot content (particle diameter â?¥0.25mm), % â?¤12.0 Average fiber diameter, μm â?¤7.0 Density tolerance, % +15, -15 Thermal conductivity coefficient (average temperature: 70±2), W/(m. K) â?¤0.043 Thermal load contraction temperature (products with density above 60kg/m3), â?¤ 600 Acidity coefficient mk â?¥ 1.6 Moisture content, % â?¤0.5 Combustion property Non-combustible(A class) Organic material content, % â?¤ 4.0 Water repellence (water-proof), % â?¥ 98 Water absorption (water-proof), % â?¤ 5 Max Application Temperature 650
Integrated solution for surface engineerings. 1. Polyurethane binder, one component binder. Polyurethane paving materials, two component binder, A:B materials Ratio 7:1 - 2:1. 2. TPE artificial grass infilling granules, 20%, green. 3. EPDM rubber granules, 11% 16% 20%, red/green/blue.... 4. Silicon PU coating, red/green/blue... 5. Spraying polyurea. Products application: sport track & field, Children playground, fitness trails, PU binder series to indoor/outdoor wall waterproof and anti-corrosion coating.
Integrated solution for surface engineerings. 1. Polyurethane binder, one component binder. Polyurethane paving materials, two component binder, A:B materials Ratio 7:1 -2:1. 2. TPE artificial turf granules, 20%, green. 3. EPDM rubber granules, 11% 16% 21%, red/green/blue.... 4. Silicon PU coating, red/green/blue 5. Polyurea spray coat paint ....
Integrated solution for surface engineerings. 1. Polyurethane binder, one component binder. Polyurethane paving materials, two component binder, A:B materials Ratio 7:1 -2:1. 2. TPE artificial turf granules, 20%, green. 3. EPDM rubber granules, 11% 16% 21%, red/green/blue.... 4. Silicon PU coating, red/green/blue 5. Polyurea spray coat paint ....
Dongfang Yoyik Engineering Co., Ltd is located in Deyang, Sichuan, provides different kinds of industrial products and brands. Our company is specialized in researching and developing hear-resisting and wear-resisting materials. As a pump and valve manufacturer ourselves, we also offer other brands both domestic and from abroad. Pin GB120G-86 Cross Pin M206-361200A OUTER COVER YT47-231000A011 Pin GB120-86 Bypass Sealing Fin 57YR43-2 Pin GB120G-86 CV LVDT Sensor 191.36.09.01 Sensor DET-400B Special nut for coupling D11.211.007 EH oil main pump oil seal W.26.A.0196 Gasket M206-261000A005 sealing ring W.26.A.0308 SEAL,STEAM,LP-B5TH DIPRAGM D600B-098290A FINS FOR LP GEN SIDE 3RD STAGE DIAPHRAGM SEAL D600B-117000C INSULATION WASHER 4Q7313 Supporting Board 162YR41-16 Adjust Gasket D135A-241000C001 TRIP & LOCKOUT VALVE D1000A-467000B FD Fan Main Bearing Sealing Ring UG13832 Φ232/200*6 Gland Seal D60R-100300A Booster Fan YKS1120-10 washer 4Q7311 jacking oil pump suction filter w.38.C.0096 Main steam valve stem D125A-265000A028 FINS FOR LP GEN SIDE 5TH STAGE DIAPHRAGM SEAL D600B-119000C servo valve W.01.Z.000152 HP guide steam pipe flange bolt D42.291.009 Bolt Heater HY-GYY-2.4-380V/3 Metallic Spritolic Gasket D600B-29600B002 GEAR SHAFT D600A.231.11Z SPECIAL STUD D00.010.168 EMERGENCY TRIP DEVICE D1000A-421000B Pin GB120G-86 ã??2019-06-13-DFJerryã??
Our products range. Vigortech is the leade rof angle measurement field. We always supply the advancedand good performance tiltsensors to theconstructionmachinery. 1)static inclinometer--20 types, it has good ability to resist vibration filter and suitable for measuring in static. 2)quasi-dynamic inclinometer--8 types, its suitable for measuring under affection on continuous acceleration. 3)dynamic inclinometer--5 types, its suitable for measuring in dynamic slope. 4)more than 4 types inclinometer can stand 400g impact. 5)more than 3 types inclinometer are suitable for applying to the insideof drill pipe. Basing on our many years experience, we think the importantpremiseforachievinghighsafety is that can accurately measure the angle by tilt sensor under emergency.
1. Item: ZEBRA BLINDS, VISION BLINDS, COMBI BLINDS 2. Fabric material:100% polyester 3. Fabric Color: Refer to our color swatch or custom made 4.Fabric feature : Semi-blackout / Blackout 5. Components:Aluminum head rail, aluminum head tube, aluminum bottom rail, roller mechanism, operation chain, end cap, brackets etc 6. Blinds Size:As customers requirements 7. Control system:1.Manual chain control 2.Electrical remote control 8. MOQ:1PCS 9. Package: Inner: plastic clear box for each piece blinds Outer: carton 10. Delivery time:Normally is about 15-30 days after the confirmation of order, it also depends on your order. 11. Shipment:DHL, UPS, FedEx, TNT, Air freight, Sea Shipping etc 12. Payment:T/T, L/C, Western Union 13. Application:Bedroom, living room, office, bathroom, kitchen etc 14. Sample: Available
Formwork accessories, dywidag wing nut, tie-rod, plate, water stop, tripod, fork head, anchors, u-head, base jack We can supply all kinds of formwork accessories, such as wing nut, tie-rod, plate, water stop, tripod, fork head, anchors, u-head, base jack, etc. Also, we can supply all types of scaffolding parts & fittings for ringlock scaffolding system, cuplock scaffolding system, kwikstage scaffolding system and frame scaffolding system. All these accessories are universally used, some of which can work well with doka and peri formwork systems.
Cement cabin We provide various kind of specificaiton cement silo from 30t to 1000ton, and we also provide cement silo in Slice, it is suitable to store cement, coal ash, grain every kind of powder and granule materials etc. On the body, there is equipment to show the position of material inside. The cement silo in slice is suitable to export by containers, it reduce the transportation fees greatly. Model30t50t80t100t150t200t300t500t Volume(t)305080100150200300500 Tank2.62.63334.54.56 Diameter(m) Tank body height(m)4.85.4811.418.622.223.524.6 Total height(m)11.412131823.525.228.829.5 Matched mixerjd350js500js750js1000js1000js1500js2000js3000 Screw conveyorlsy163lsy 180lsy180lsy 230lsy 230lsy 230lsy 230lsy 230 -
Property Kol-rtd m cem can absorb on the surfaces of cement hydrate to inhibit contact with water and on the surfaces of crystal nucleis to prevent their increase. So it can retard hydrating of cement slurry. Basic data AppearanceDosageScreeningsApplicable temperatureOperation method Yellowish powder0.1%-1.0% (bwoc)=15.0 (residue on 0.315mm sieve), %Below 110?(bhct)Dry mix Technical data ItemsSpecificationSlurry formulation Moisture content, %=10.0Class g cement , w/c 0.44 , dosage of rtd m cem 0.1%-1.0% (bwoc) Water quality: distilled water Initial consistency, bc, 80?. 46.5mpa. 45min=30 Thickening time adjust-abilityAdjustable Free fluid, %=1.4 Compression strength, mpa/102?. 21mpa. 24h=14 Feature Used in middle-deep well and deep well, retard the thickening time efficiently. Increase the pump ability time. Have a strong dispersing performance. Package & storage Be sacked with three packages, 25kg/sack. Be kept away from moisture and possible damage of the packages in transportation. Storage life is two years.
Property Kol df cem can defoam through reducing surface tension of liquid. Basic data AppearanceDensityDosageScreenings (residue on 0.420mm sieve), % White powder1.45g/cm30.3%~0.5%(bwoc)=7 Technical data ItemsSpecification Deforming ratio, %=90.0 Cement slurry density, g/cm3=1.86 Feature It’s non-toxic, odorless, non corrosive, and friendly to the environment. It has various functions such as inhibiting foam, defoaming, and perverting mingrating of gas. It defoams rapidly. Resist corrosion of acid and base, as well as high temperature. Has good compatibility with other additives. Has no harmful influence on other properties of cement slurry. Package & storage Packaging and transport in sacked with three package, 25kg/sack. Kept away from fire, damage and leakage in store and transportation.. Storage life is two years.
Rymax foam cement board | exterior drywall Of, anti-shock and pollution-free. The core layer made of polystyrene concrete heavily reduces the weight and enables the panel to form multi-arched structures and have high flexural strength and compressive resistance. The groove and tongue structure helps to build a strong and stable structure in one piece. The industrialized production helps shorten the construction period and enhance the installation efficiency, also the panel is nice decoration and easy for installing piping. Since the wallboard is light and thin, it greatly reduces the loads of the foundation, beams and columns and Environment-friendly; Energy-conservative; Fire-proof; Factory packing
1.Seamless steel pipe: od: 13.72mm-914mm, wt: 1.25mm to 100mm Cold-drawn: à-114.3mm, hot-rolled: 114.3-406mm, expanded: 406-914mm 2. Erw steel pipe: od: 21.34mm-660mm, wt: 1.65mm to 25mm 3. Lsaw steel pipe: od: 406mm-1625mm, wt: 8mm to 65mm 4. Ssaw steel pipe: od: 219mm to 3120mm, wt: 3mm to 25mm 5. Stainless steel pipe: od: 6.0mm-830mm, wt: 1.0mm-24mm 6. Hollow section steel pipe: square/retangular/roun 1.Seamless steel pipe: od: 13.72mm-914mm, wt: 1.25mm to 100mm Cold-drawn: -114.3mm, hot-rolled: 114.3-406mm, expanded: 406-914mm 2. Erw steel pipe: od: 21.34mm-660mm, wt: 1.65mm to 25mm 3. Lsaw steel pipe: od: 406mm-1625mm, wt: 8mm to 65mm 4. Ssaw steel pipe: od: 219mm to 3120mm, wt: 3mm to 25mm 5. Stainless steel pipe: od: 6.0mm-830mm, wt: 1.0mm-24mm 6. Hollow section steel pipe: square/retangular/roun
China (Guangzhou) Intl Exhibition for Steel Construction & Metal Building Materials (Steel Build 2016) Date: May 13th-15th, 2016 Venue: Poly World Trade Expo Center(PWTC) China Market, With Boundless Business Opportunities! In recent years, Green Building becomes the focus of environmental protection. As an important representative of green buildings, steel structure is bound to be placed on the top priority in the development of the society. Therefore, China must be the market you never ignore and Steel Build 2016 is a must-come event for companies who are going to step into this expanding market in future decades. About Steel Build As one of the important thematic exhibitions of China (Guangzhou) Int¡¡¡¨º¡¨¨l Housing Industry Expo, Steel Build 2015 has successfully held in Guangzhou, China with the support of China Council for the Promotion of International Economic and other well-known organizations and media. Steel Build 2015 and concurrent events of China (Guangzhou) Int¡¡¡¨º¡¨¨l Housing Industry Expo(CIHIE) has successfully gathered 700 exhibitors in total. Nearly 100 worldwide famous exhibitors including FRAMECAD, CHINATOTAL, VERTEX CAD/PDM, METAL-EXPO, Lai Gang Integrated Building (Qingdao) Development Co., Ltd., Qiguang Group, etc, were attracted to demonstrate their latest steel products and technology. And 850 high quality buyers from 75 countries attended the show and most of them felt it a fruitful trip and were willing to attend the show next year. With 4-years rich experience, Steel Build 2016, ceremoniously staged in Poly World Trade Expo Center from May 13th to 15th, 2016, is devoted to creating a perfect platform for worldwide industry related merchants and purchasers to promote communications and cooperation. In addition, as a major exhibition of China (Guangzhou) Int& ¨¨l Housing Industry Expo(CIHIE), more related exhibits and products like prefab/modular houses, mobile cabins, waterproofing products, etc can be found during the same period. Concurrent Event--Special exhibitions of China (Guangzhou) Int¡¡¡¨º¡¨¨l Housing Industry Expo(CIHIE) The 6th China Prefab House, Modular Building, Mobile House & Space Fair The 8th Guangzhou International Wooden House&Wooden Structure Fair The 6th China International Roof,Facade & Waterproofing Exhibition The 6th China Rooftile & Technology Exhibition China Guangzhou International Floor Fair Exhibition Scope Steel frame buildings, Space frames Structural Steel Fastening & Fixing Systems Protection-Drywalls, gypsum board, Fire stops, Fireproof Sprays/ Coats, etc Insulations Keel/curtain wall/façade and roofing systems Pre-Engineered Building Systems (PEB) Structural Steel Machinery & Tools Software Solutions for steel structures Steel Tubes/ Pipes/ Structural Hollow Sections Sheet Metal Materials Metal Decking/Floorings Metal Profiles For more detailed information about Steel Build 2016, please kindly refer to http://www.steelbuildexpo.com/ or email us at grand.wa@grahw.com.
The cover is vinyl resin material and inside is stainless steel,it is resistant scraping and anti-microbial. The width is 150mm, thickness of panel is 2mm.
