1. Chopped basalt fiber Basalt fiber is a kind of inorganic fiber material. Chopped basalt fiber is an inorganic mineral fiber with a length of less than 50mm and can be evenly dispersed in cement concrete. 2. Characteristics of chopped basalt fibers (1) The naturalness of raw materials. Because the raw material for producing continuous basalt fiber depends on the natural volcanic extrusive rock, there are no ingredients harmful to human health except that it is inherently high in chemical stability and thermal stability. (2) Comprehensive performance. Basalt fiber is acid resistant and alkali resistant. It is both low temperature and high temperature resistant. It is insulated and insulated by heat and electricity. Its tensile strength is higher than that of large tow carbon fiber. Its elongation at break is even better than that of small tow carbon fibers. It has high compressive strength, shear strength and adaptability to aging, and has good comprehensive properties in harsh environment. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of steel fiber and polyester fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with asphalt concrete, cement concrete and mortar. The newly mixed basalt fiber concrete has stable volume, good workability and durability, and has superior high temperature resistance, anti-seepage, crack resistance and impact resistance.
1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.
Produced by Chongqing Hesheng Longgang Technology Co., Ltd. (manufacturer) Basalt fiber reinforcement (new material to replace reinforcement) Product Description: basalt fiber reinforced bar (BFRP) is a new composite material formed by pultrusion process. It is made of basalt fiber as reinforcement, resin, filler and curing agent. Now it has been widely used in construction, highway and bridge constructionã?? Basalt fiber reinforcement can completely replace ordinary steel reinforcement and deformed steel; Compared with ordinary reinforcement, it has strong advantages: (see Annex for technical parameters) 1. The cost is the same as that of ordinary reinforcement; 2. The strength is 200% of the ordinary reinforcement with the same specification and diameter; The tensile strength reaches 1100mpap; The reinforcement is only 450MPa, 3. Basalt fiber reinforcement, especially with high acid, alkali and corrosion resistance, is a kind of electrical insulator that will never rust. 4. Basalt fiber reinforced bar, which is non-magnetic. It has high tolerance to the moisture concentration in cement mortar and the penetration and diffusion of carbon dioxide, and can prevent the corrosion of concrete structure in harsh environment, so as to improve the durability of buildings and bridges. 5. The specific gravity of basalt fiber reinforcement is 2.1g/cm3; The specific gravity of steel and reinforcement is 7.85/cm3; The diameter weight of the same specification is 370% lighter than that of steel reinforcement, and the strength is 200% of that of steel reinforcement. 6. The physical properties of basalt fiber reinforcement are higher than that of steel reinforcement, and the cost is the same as that of steel reinforcement, which is of epoch-making significance to replace steel reinforcementã??
Basalt Fiber Series Fabric 1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating. 2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth. 2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc. 3. Packaging: 100M / roll (or customized as required). 4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance.High temperature resistance 1000 �° C 5. Specification and model: bfw16 * 20-100 (120) BFW: basalt fiber fabric;Completely replace carbon fiber sheet building reinforcement 16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively; 100: the width of the fabric is 100 cm; (120): the mass per unit area of fabric is 120 g / m2. BFNP5*5-200(160) BFNP: basalt fiber mesh cloth (coated and shaped); 5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm; 200: the width of the grid is 200 cm; (160): the weight of grid cloth per unit area is 160g / m2.
1. Basalt short fiber - a new material to replace steel fiber. Basalt short fiber is an inorganic mineral fiber with a length of less than 50mm, which can be evenly dispersed in cement concrete. 2. Characteristics of basalt short fiber (1) the specific gravity of steel fiber is 7.8 and that of cement concrete is 2.5. After mixing, the specific gravity of steel fiber is higher than that of cement, and the cement will sink and have poor dispersion. The specific gravity of basalt short fiber is 2.6, which is basically equivalent to that of cement concrete. After mixing, it does not sink, has good dispersion, is degradable, and is green. The road surface will not be as hard as steel fiber, resulting in car driving noise.. (2) Basalt staple fiber is a real "multifunctional" fiber. Acid and alkali resistance (especially alkali resistance, fully applicable to cement concrete), low and high temperature resistance, insulation and sound insulation. The tensile strength is three times that of steel fiber. The corrosion resistance of basalt fiber is better than that of steel fiber. The compressive strength is 20% higher than that of steel fiber, which is suitable for harsh environment. It has excellent comprehensive performance. (3) Low cost. The price of basalt fiber used in cement concrete is significantly lower than that of 50% steel fiber. (4) Natural compatibility. Basalt fiber is a typical silicate fiber, which is easy to disperse when mixed with cement concrete and mortar. Fresh basalt fiber concrete has stable volume, good workability and durability, and has excellent high temperature resistance, impermeability, crack resistance and impact resistance.
Basalt Fiber Series Fabric 1. Production: basalt fiber fabric is made of continuous basalt fiber textile yarn through warping, weaving and coating. 2. Weaving methods according to requirements: unidirectional cloth, plain cloth, twill cloth and grid cloth. 2. Application: reinforced mesh cloth, fireproof cloth, fishing rod cloth, luggage decoration cloth, electrical insulation cloth, bulletproof cloth, etc. 3. Packaging: 100M / roll (or customized as required). 4. Performance: high strength, high temperature resistance, good electrical insulation, non hygroscopic, acid and alkali corrosion resistance. 5. Specification and model: bfw16 * 20-100 (120) BFW: basalt fiber fabric; 16 * 20: the warp and weft density of yarn is 16 and 20 pieces / cm respectively; 100: the width of the fabric is 100 cm; (120): the mass per unit area of fabric is 120 g / m2. BFNP5*5-200(160) BFNP: basalt fiber mesh cloth (coated and shaped); 5 * 5: the longitude and latitude mesh size of the cloth surface is 5 and 5mm; 200: the width of the grid is 200 cm; (160): the weight of grid cloth per unit area is 160g / m2.
Produced by Chongqing Hesheng Longgang Technology Co., Ltd. (manufacturer) Basalt fiber reinforcement (new material to replace reinforcement) Product Description: basalt fiber reinforced bar (BFRP) is a new composite material formed by pultrusion process. It is made of basalt fiber as reinforcement, resin, filler and curing agent. Now it has been widely used in construction, highway and bridge constructionã?? Basalt fiber reinforcement can completely replace ordinary steel reinforcement and deformed steel; Compared with ordinary reinforcement, it has strong advantages: (see Annex for technical parameters) 1. The cost is the same as that of ordinary reinforcement; 2. The strength is 200% of the ordinary reinforcement with the same specification and diameter; The tensile strength reaches 1100mpap; The reinforcement is only 450MPa, 3. Basalt fiber reinforcement, especially with high acid, alkali and corrosion resistance, is a kind of electrical insulator that will never rust. 4. Basalt fiber reinforced bar, which is non-magnetic. It has high tolerance to the moisture concentration in cement mortar and the penetration and diffusion of carbon dioxide, and can prevent the corrosion of concrete structure in harsh environment, so as to improve the durability of buildings and bridges. 5. The specific gravity of basalt fiber reinforcement is 2.1g/cm3; The specific gravity of steel and reinforcement is 7.85/cm3; The diameter weight of the same specification is 370% lighter than that of steel reinforcement, and the strength is 200% of that of steel reinforcement. 6. The physical properties of basalt fiber reinforcement are higher than that of steel reinforcement, and the cost is the same as that of steel reinforcement, which is of epoch-making significance to replace steel reinforcementã??
Material: Iron Height: 4.5cm Diameter: 4.5cm Sound Press: more than 110dB Bell color can be customized
Basic principles Computer controls marking-needle to move on traces of pre-edited characters and graphs, meanwhile, to strike materials at a high frequency under the application of compressed air, thereby, to form needed characters and graphs. Major functions Software applicable on windows 98/2000/xp/vista platform, has strong editing functions, and easy to use, capable to mark chinese and english characters, arabic numbers and graphs, automatic marking serial numbers, international standard vin codes. The marking head could move 90 degree, suit for different marking requirement.
Basic principles Computer controls marking-needle to move on traces of pre-edited characters and graphs, meanwhile, to strike materials at a high frequency under the application of compressed air, thereby, to form needed characters and graphs. Major functions Software applicable on Windows 98/2000/XP/Vista platform, has strong editing functions, and easy to use, capable to mark Chinese and English characters, Arabic numbers and graphs, automatic marking serial numbers, international standard VIN codes. The marking head could move 360 degree, suit for different marking requirement. Features Marking speed 3-5 characters(2x2mm)/s Marking depth 0.1-1mm upon the different materials Marking contents characters, alphanumeric, date, numbers, serial NO,VIN code etc. Marking area 140x80mm (customized support) Up and down lifting height 0¡ª350mm Work bench 340mm¡Á440mm Marking materials below HRC60 metallic and nonmetallic materials (above HRC60 need special stylus) Repeat accuracy 0.02-0.04mm Work voltage/power AC220V¡À10%50Hz/300W Inputting air pressure 0.3¡ª0.6MPa Operating System Support WinME.Win2000.WinXP Applications To be applied in Automobile, bodywork of motorcycle, car frame ,automotive chassis, engine, mechanical part, machine tool, metal pipe, gear, pump body, valve, various hardness plastic products, hardware part, Aeronautics, Electronics, war and light industry for marking steel, iron, copper, aluminum and plastic parts and various nameplate marking. 1.Direct Part Marking(DPM) 2.Metal components marking 3.Component identification 4.Component traceability 5.Serial numbering 6.Security marking 7.Health and safety appliances marking 8.Certification marking 9.Time and date marking 10.Part numbering 11.Batch and shift coding 12.Label, plate and tag marking Basic settings 1.Advanced USB interface control technology 2.Taiwan HIWIN linear guide 3.Automatic System Trouble Analysis 4.Japan SMC high-frequency electromagnetic valve 5.Big torque, small angle stepper motor 6.High precision power driver 7.ThorX6 marking software 8.Rotory fixture supported Software Main Function Multi-languages, serial No., Arabic numerals, arbitrary figure, incrementing serial No., graphics, VIN code, time, date, barcode reading marking, ticket, dot matrix, 2D code(two-dimension code), circumferential parts marking and connected to database marking. Available in a variety of languages (including English, French, German, Spanish, Swedish, Finnish, Italian, Portuguese, Cyrillic and Czech), the software also contains features such as serial numbering, date and time marking and password protection. Support multiple graphics and fonts, compatible with AutoCAD, CorelDraw. Flexible and user-friendly software, compared with the same numbers. Database: Marking report available, special fonts and graphics editor. Major parts Desk top marking machine, PC based marking controller Spares Air pressure valve, two marking pins, RS-232 and USB data line, 19 core cable, power line, software CD Return and feedback I. As we do not have the maintenance department at overseas, you can send back the problem spare parts to maintenance or replacement the new spare parts. II. We depend on our domestic reputation and customer satisfaction to succeed. Therefore, your feedback is extremely important to us. After-sales Services One year guarantee for main machine. (People damaged are charged). Lifelong maintenance and spare parts supply. Free design of fixtures as customers required. Free training installation and operation for the staffs.
HMS, CDSO, CPO, cement, hdpe, yellow corn, sugar, used rail, and other products such as fishes (salmon, trout, squid), wines, omega-3.
Details: Alloy: 1100/1050/1060 3003 5052 Temper: HO/H12/H14/H16/H18 Specification: Thickness: 0.5mm-6mm Diameter: 80mm-1500mm Width: 600mm-2630mm 20-2400mm Type: /Coated/Cladding MOQ: 3 TON Application: DC quality: Deep drawing quality, Less scrap. Suitable for making cookware and following products: Stock pots/Fry pans/Pressure cookers/Pizza pans/Restaurant cookware/Bakeware/Bread makers/Woks/Tea kettles/Rice cookers/Electric skillets/Coffee urns/Stainless cookware bottom plates CC quality: Good surface, suitable for lighting industry. Applications for our froducts: Recessed lighting/High bay industrial lighting/Low bay industrial lighting/Street lighting/Traffic light reflectors/Sports lighting
1)marking contents:numbers, chinese and english characters, graphs 2)size of characters:adjustable 3)marking depth 0.02-1mm(adjustable, relevant to materials) 4)marking speed 2-5 letters per second according to letter size 5)marking materials:metals or nonmetals with hardness under hrc55 6)marking surface:flat surface (120x80mm, can be change as customer's request) 7)power source ac220v10%50hz 8)pneumatic pressure:0.3-0.7mpa 9)energy consumption:100w(air compressor excluded) 10)repeat precision:0.02-0.05mm 11)work enviroment:regular work environment 12)function introduction: pneumatic marking machine with a rotatable fixture, can mark on workpiece with flat or curved surface, directly mark on the body, base plate, pillar and engine 13)applicable scope:motor industry:mark serial number, manufactural date, name, brand, etc.On pillar, engine and other big and heavy materials 14)major parts:main machine.
Product parameters 1. Material: copper 2. Model number: 3-m26 3. Pin hardness: hrc95 4. Pin length: 53mm 5. Pin diameter: 2.5mm 6. Marking depth:0.02-2mm 7. Size of characters:
Basic principles Computer controls marking-needle to move on traces of pre-edited characters and graphs, meanwhile, to strike materials at a high frequency under the application of compressed air, thereby, to form needed characters and graphs. Major functions Software applicable on windows 98/2000/xp/vista platform, has strong editing functions, and easy to use. It could mark chinese and english characters, arabic numbers and graphs, automatic marking serial numbers, international standard vin codes. It could be easily move around and marking on un-movable parts through 5 meter long cable.
permanent magnet rotro structure,no field winding, no carbon brushes, no slip rings, simple structure, high speed, small size, light weight, and large power densityreliable and durable high efficient,small heat ,long life save energy more than 15% than ordinary mortors
Marine gratings and marine grilles fully comply with CBT608 and CBT615. Steel and stainless steel gratings are produced mainly by welding. First, we will punch or slot the flat steel, then place the crossbar into the hole for spot welding. Each contact point of the cross bar and the flat steel is properly welded. The crossbar can also be welded by spot welding. welding staff have the top grade industry profession certification The base of the grilles or gratings could be material of steel ASTM A36, stainless steel 1cr18ni9ti, FRP,polyester and etc. Our new product molded polyester grating is using glass fiber as the reinforcing material, using the unsaturated polyester resin as substrate and then specially processed and compounded to be strong and anti-slip. Our grilles could be used as bilge suction grilles for shipbuildiing, deck walkway gratings, Marine submarine door grilles and etc.
Features HGQ40 steel bar cutter adopts enclosed housing, lubricate system, dual-mass flywheel and with clutch structure. It works with high efficiency and safety, which is easy to operation and maintain, light in weight and energy saving. Double Mass Flywheel, which assure strong enough power for cutting.
Alloy ASTM SCH40 DN50 pipe ells 1. Alloy pipes, high-pressure carbon steel pipes, and cryogenic pipes for petrochemical power industry 1) Cr5Mo (STFA25 STBA25 STPA25 T5 P5) 2) 15CrMo (STFA22 STPA22 STBA22 T12 P12) 3) 1.25Cr0.5Mo (STFA23 STPA23 STBA23 T11 P11) 4) 12Cr1MoV (12Cr1MoVG) 5) 12Cr2Mo (10CrMo910 T22 P22) 6) T91 (P91) 7) 102[12Cr2MoWTiB(R102)] 8) Cr9Mo (STFA26 P9) 9) High temperature and high pressure pipe: SA106B (ST45.8 ¢20G) SA-210C 10) Cryogenic tube A333GR1 A333GR6 A333GR3 11) Stainless steel for high temperature: TP304H TP321H 12) High temperature alloy 1CR25NI32 Incoloy800H (B407 NO8810) 0CR25NI20 (310S) 0CR23NI13 (309S) 1CR15NI75 (Incoloy600) High temperature pressure centrifugal casting tube: HH30 HH33A HI35 HK30 HK40 HL30 HL40 Nickel tube: N8 (NO2200) High Nickel Alloy Tube: NCU28-2.5 (MONEL 400) Pure titanium tube: TAL(TP28/CR1) TA2(TP35/CR2) TA3(TP49/CR3) Copper Nickel Alloy Tubes, Plates, Rods: BFE10 BFE30 2. Stainless steel pipe and plate 0Cr18NI9(304/304H) 00Cr19Ni9(304L) 1Cr18Ni9Ti(321/321H)0Cr17Ni12Mo2Ti(316/316H) 00Cr18Ni14Mo2(316L) 3. Alloy steel pipe and alloy plate 12Cr1MoVG 15CrMoG .Cr5Mo. A387 GR11 4. Bridges, grids, workshops Special seamless steel pipes, rectangular pipes and square pipes for steel structures. 20#, 16Mn (Q345B C D E ) 5. Special pipes for machining and hydraulic support pipes. 20#, 35#, 45#, 27SiMn, 35CrMo, 42CrMo 6. Carbon steel pipe 1) ASTM106 series, A53 series, API line pipe, ST45.8/ ¢ high temperature and high pressure pipe SA-210C, A333GR1 GR6 GR3 low temperature pipe 2) Seamless steel pipe material: (10#, 45#, 20#, 35#, 16MnQ345 (A, B, C, D, E), machined pipe 27SiMn, 42CrMo, 35CrMO, Dz40, J55/K55, N80 ( Q), L80, N80-1 Specifications: outer diameter �¤6mm-1080mm wall thickness 1.5mm-120mm
Rubber fender, anchor chain, glass wool, rock wool, mooring equipment, crane, windlass, steel material, laser cutting machine, boring machine, drilling machine, etc..
