Block machine, block making machine, concrete block making machine, concrete block machine, hollow block making machine, hollow block machine, mobile block making machine, mobile block machine, small block making machine, small block machine.
Hss twist drill bits, sds plus hammer drill bit, hss machine taps, hss step drill bits, hss center drill bits, wood working drill bits, masonry drill bits, end mills, diamond cutting disc, tct saw blade.
Waterproof slurry, lacquer putty, ceramic tile adhesive, sealant, waterproof agent, stain control agent, cleaner.
The cementing plug is used to separate the cement slurry from the mud. It can prevent the mud from blending into the cement slurry to influence the cementing quality. Structure: conventional cementing plug & special cementing plug Conventional cementing plug is divided into top plug and bottom plug. Special plug has top/middle/bottom plug used in two-stage cementing, drill pipe plug and hollow plug used in drilling liner cementing and composite plug used in composite casing.
PCE superplasticizer is the newest generation superplasticizer used for concrete in domestic and abroad.It is based on molecular designs and adsorption capacity of polycarboxylate,we do R&D and successfully produce water reducing and retention type polycarboxylate superplasticizer for concrete.With initiating systerm and reaction conditions,we achieve high adaptability. Polycarboxylate Superplasticzier we produce types as below: 1. High water reducing type (normally they can be satisfied for concretes' requirements): JH03 basic standard type(under most exported.) JH09 viscosity adjustment is better than JH03,water reducing ratio is lower than JH03,(suitable for high clay content ratio of cement,under most exported.) JH15 water reducing ratio is higher than JH03,performance is better than JH03,suitable for high strength concrete.(New Research and technology higher than JH03.) 2. Water reducing and slump retention type JH02 water reducing and slump retention type.(New Research on base of JH03.) 3. High slump retention type JH06 basic standard type,mix with JH03 and JH09 if concrete's slump retention is not satisfied.(under most exported.) JH06K higher slump retention performance than JH06,price is higher than JH06,mixing with JH03 and JH09 if concrete's slump retention is not satisfied.(under most exported.) JH16 Better performance and different technology with JH06 and JH06K,mixing with JH03,JH09 and JH15 if concrete's slump retention is not satisfied.(New Research and technology to satisfy JH15.) Exporting loading: 20'GP container loading: 1. 220kg/drum, 80 drums 17.6 T 2. 1150kg/drum,20 drums 23 T 3. 20-25tons/flexitank. 20-25 T
Our main products including Iron wire: galvanized wire, black wire, barbed wire, PVC coated wire, flat wire, oval wire, loop wire, stainless steel wire Iron nails: common nails, roofing nails, headless nail, square boat nails, U type nail Wire mesh: chain link fence, galvanized welded wire mesh, hexagonal wire netting, window screen, cattle farm fence, stainless steel wire mesh Many construction materials: round tube, square tube, galvanized steel pipe, galvanized steel plate, HR sheet, CR sheet, roofing sheet, PPGI sheet, galvanized steel strip, steel coils, angle bar, flat bar, I beam, H beam, plywood, SCAFFOLDING etc
Acoustic Mineral Fiber Ceiling Board can be economically loaded with ceiling grids produce by Sinoceling.com into 1x40'HQ. it is made of wet-formed mineral fiber with low density: 220-260kg/m3, including square edge & tegular Edge finish. Mineral fiber board has many features: Strong and lightweight finish; dimensional stable; High humidity resistance; So far, Mineral fiber ceiling tile is easy to be installed with our T24 ceiling tee grid by SINOCEILING, which has been widely applied for offices, schools, hospitals, theatres, music house, power stations and so on.
Thermoplastic Toe Puff & Counter Material Also named as Nonwoven Hot Melt Quality: SEXE#, SEXH#, SGHX#, SGHG#. SEXE# & SEXH# can compare well with the ones offered by European manufacturer in excellent cost-performance. Thickness: 0.60MM-2.50MM Size: as per negotiation. Max Width: 1.00M Application: heat-bonding for shoesâ?? toe puff & counter, also to be used in the padding of cover & bags & boxes & cap tongue etc. Public by J. Z. Industry & Trade Co., Ltd, a leading & professional manufacturer of shoes material
Sodium naphthalene sulphonate formaldehyde produces concrete with extremely workable characteristics referred to as high slump. Pns also allows concrete to be produced with very low water/cement ratios at low or normal slumps. Sodium naphthalene sulphonate formaldehyde is ideal for use in prestress, precast, bridge deck or any concrete where it is desired to keep the water/cement ratio to a minimum and still achieve the degree of workability necessary to provide easy placement and consolidation
Roof Reflective Insulation Material,Epe Foam Cover Aluminium Film * Function: Material with the features of dampproof, shockproofing, sound insulation, heat preservation, sun shade, heat isolation and good plasticity. It is an ideal substitute of traditional packing materials and used widely in the packing of electronic products, daily necessities, glass, cooler bag, potteries, electrical household appliance, spraying, furniture, hardware products and toys. * Packing: OPP bag * Payment: T/T * Origin: China * Min. Order: 5000 square meters * Delivery time: 30day
Mullite refractory castable general use of mullite aggregate to as raw materials and configuration of a kind of low temperature in the insulation refractories, it is commonly used in the petrochemical industry tube furnace, light diesel oil, ethane cracking furnace lining, atmospheric and vacuum furnace and sulfur recovery device and steam boiler, tortoiseshell net heat insulation layer, two barrel and pipe insulation monolayer, and other industrial furnace door, see the fire hole, observation hole door lining, etc. The advantage of mullite refractory castable is that its refractory temperature is higher than other thermal insulation castable, which can be directly in contact with the flame and used as the lining of the kiln. Another kind of refractory castable is corundum mullite castable, which is a refractory castable prepared with corundum as aggregate and powder plus some binder.It has higher mechanical strength and abrasion resistance than high alumina refractory and Mullite refractory, but less thermal shock resistance.
HPMC is a type of non-ionic cellulose ether, white powder appearance, odorless and tasteless, soluble in water and most polar organic solvents. Its water solution has a surface activity, high transparency, stable performance. HPMC has a thermal gel properties, after heating, the product solution formed the gel precipitation, dissolving after cooling. Different specifications products have different gel temperature. Solubility changes with viscosity's difference. The lower viscosity, the higher solubility, different specifications HPMC have difference in properties, dissolving HPMC in water won't be affected by PH value.
Steel fiber castable is widely used in high temperature vulnerable parts of metallurgy, building materials and circulating fluidized bed boilers.As follows: according to the classification of the material, it is suitable for planning the corundum quality before and after the steel fiber reinforced castable first used in large cement kiln kiln and other industrial kiln lining, high aluminum and corundum mullite stone steel fiber reinforced refractory castable first used in the cement kiln kiln mouth, wicket cover, before and after cooling machine in high temperature resistant parts and other industrial kiln liner.
Non-stick aluminum refractory castable or non-stick castable, the non-stick aluminum castable combines with the feature of inorganic binder, add a certain amount of insoluble in aluminium new composite refractory material, control the liquid aluminum erosion of refractory, non-stick aluminum castable with high volume density, high strength, not for the nature of the aluminum liquid wetting, can significantly reduce the corundum phase anomaly grew up and molten metal and permeability of materials.Suitable for the bottom of aluminum melting furnace, wall of furnace, slag-scraping slope, chute, aluminum water bag and degassing box, etc.
High alumina castable is a refractory castable made of high alumina raw material with binder and aggregate in traditional ratio.On the basis of the preparation of high strength and high aluminum castable, the granule gradation is adjusted, different admixtures are added, cement dosage is reduced, performance is improved, medium temperature strength and softening temperature under load are increased, thermal conductivity is reduced, and thermal stability is good.The furnace body structure integrity is strong, the air tightness is better than the brick furnace, extends the furnace life, saves the furnace repair cost, the economic benefit is remarkable as the high aluminum refractory castable characteristic.
The improvement of the performance of low cement casting material is actually the application of micro powder technology. There is a gap between the stability of low cement castable and that of laboratory castable.Low cement castable easy to occur problems are: 1, poor construction performance, poor liquidity;2. The hardening speed varies greatly, and there is quick setting or non-setting;3, easy to burst in baking;4. Abscission occurs;5. Low strength and poor wear resistance.These are caused by refractory castable products abnormal damage and other quality problems. Low cement refractory castable itself in addition to wear resistance, refractory aggregate, is used with good raw materials fine powder and ultrafine powder, cement and admixture, etc., through adjusting the proportion of each component, improve the high temperature performance of castable, thereby improve the strength of refractory castable. Low cement castable key construction, should pay attention to is: (1) do not arbitrarily increase the water content of refractory castable, (2) mold support set too high, leading to castable water content is too large and vibration compaction;(3) No mold shall be set during lining construction of feeding pipe, and castable material shall be manually daubed;(4) In order to save the mold, the maintenance is less than 48 h to remove the mold, resulting in the casting cracking or internal damage;(5) The material, shape, size, welding quality, quantity, anti-expansion treatment and unreasonable expansion joints of the anchoring parts;Do not follow the operational sequence of dry stirring, wet stirring and feeding, directly mix the dry and wet materials, resulting in the castable is not fully mixed evenly, part of the material is not wetted by water, making the castable has no strength. There are also key water issues, to use tap water, to avoid the introduction of acid and base impurities, gradually add, in order to make the dispersant in the powder to play a full role.Excessive water addition will directly lead to a significant decline in the strength of refractory castable construction, and in the field construction the water addition tends to exceed the degree of artesification.The pouring body itself is easy to appear when the ambient temperature rises rapidly, the baking burst, resulting in large area of damage.Once the temperature of the castable itself is below 5 the castable will still have no strength even after curing for 24 hours.The construction and maintenance shall be carried out in strict accordance with the 48-hour mold removal mechanism. In dry areas, water and wet maintenance shall be carried out; in cold areas, airtight heating maintenance shall be realized within 48-hour maintenance to ensure the maintenance temperature. In a word, if the above points can be achieved step by step in accordance with the requirements, it will certainly improve the performance of low cement casting.
Steel fiber has good tensile strength, strong grip strength and high hardness.If steel fiber is mixed in castable, the steel fiber castable products produced by this method are not only used, wear resistant, tensile and compressive, but also have a good anti-theft effect.And its adaptability and operational planning will be wider.It can be used at different temperatures.Greatly improved product utilization rate.So now large kilns, melting furnaces and so on will mostly choose steel fiber castable.Is to travel the quality of the product and use of life, compared to down, such a product more affordable. Steel fiber castable can reduce the shrinkage of castable during curing, grilling and high-temperature use. After adding steel fiber, not only the toughness of castable can be improved, but also the impact and mechanical strength of the machine can be improved.After adding steel fiber, the thermal shock performance of castable is improved.The steel fiber castable prevents fracture or spalling by preventing microcrack and mechanical stress. Steel fiber castable is widely used in high temperature vulnerable parts of metallurgy, building materials and circulating fluidized bed boilers.As follows: according to the classification of the material, it is suitable for planning the corundum quality before and after the steel fiber reinforced castable first used in large cement kiln kiln and other industrial kiln lining, high aluminum and corundum mullite stone steel fiber reinforced refractory castable first used in the cement kiln kiln mouth, wicket cover, before and after cooling machine in high temperature resistant parts and other industrial kiln liner.
Steel fiber has good tensile strength, strong grip strength and high hardness.If steel fiber is mixed in castable, the steel fiber castable products produced by this method are not only used, wear resistant, tensile and compressive, but also have a good anti-theft effect.And its adaptability and operational planning will be wider.It can be used at different temperatures.Greatly improved product utilization rate.So now large kilns, melting furnaces and so on will mostly choose steel fiber castable.Is to travel the quality of the product and use of life, compared to down, such a product more affordable. Steel fiber castable can reduce the shrinkage of castable during curing, grilling and high-temperature use. After adding steel fiber, not only the toughness of castable can be improved, but also the impact and mechanical strength of the machine can be improved.After adding steel fiber, the thermal shock performance of castable is improved.The steel fiber castable prevents fracture or spalling by preventing microcrack and mechanical stress. Steel fiber castable is widely used in high temperature vulnerable parts of metallurgy, building materials and circulating fluidized bed boilers.As follows: according to the classification of the material, it is suitable for planning the corundum quality before and after the steel fiber reinforced castable first used in large cement kiln kiln and other industrial kiln lining, high aluminum and corundum mullite stone steel fiber reinforced refractory castable first used in the cement kiln kiln mouth, wicket cover, before and after cooling machine in high temperature resistant parts and other industrial kiln liner.
*opening doorï¼?90 degreee bending treatment as bottom pictures shown. *openingï¼?Ul certificed electric lock opening *Door gate: with 40mm fireproof plate --Thichness of wall: 60 mm --Fireproof time: 2 hours in factorys testing. *SS. plate decoration *Optional colorï¼?blackï¼?grey. *Inner spare paratsï¼?one blanket bolt for fireproof. Lock structuresï¼?three way pullingï¼?bolt of World lock . *openg angle: 183 degree.
Excellent thermal resistance Fireproof Rock Wool Board Rock Wool Insulation products are made from natural mineral wool such as basalt and dolomite. Density Thickness kg/m3 mm 60 50 70 80 100 150 / 75 50 70 80 100 150 / 80 50 70 80 100 150 / 100 50 70 80 100 150 / 120 30 40 50 80 100 / 130 30 40 50 70 80 100 150 30 40 50 70 80 100 180 30 40 50 70 80 100 200 30 40 50 70 80 100 PRODUCT FEATURES Rock Wool Board products are made from natural mineral wool such as basalt and dolomite. The natural rock are melted into melts in cupola at a very high temperature about 1500. The highest application temperature is 650. it has characters: heat insulation sound reduction, fireproof, waterproof and so on. Fire Doors Rock Wool Board advantages: - Excellent thermal resistance - Non-flammable - Easy to install - High sound absorption material - Easy handling and installation - Attractive aluminum appearance - Water-repellant - Resistant to ageing - Marine certified Application of Rock Wool Board: 1. Used for fire protection, thermal insulation in construction and building, commercial and residential buildings. 2. Used for sound absorption in roofing, celling, external wall, partition wall and floating floor. 3. Low density Environment Friendly Rock Wool Board suitable for roof and wall in the building Properties Value Density 60-150 Kg/m3 Shot content (particle diameter â?¥0.25mm), % â?¤12.0 Average fiber diameter, μm â?¤7.0 Density tolerance, % +15, -15 Thermal conductivity coefficient (average temperature: 70±2), W/(m. K) â?¤0.043 Thermal load contraction temperature (products with density above 60kg/m3), â?¤ 600 Acidity coefficient mk â?¥ 1.6 Moisture content, % â?¤0.5 Combustion property Non-combustible(A class) Organic material content, % â?¤ 4.0 Water repellence (water-proof), % â?¥ 98 Water absorption (water-proof), % â?¤ 5 Max Application Temperature 650
