Features: 1. Good acid and slag resistance. 2. Good thermal conductivity. 3. High tridymite content. 4. Accurate dimension and good appearance. Application: Mainly used for coke oven of coking chamber and combustion chamber partition, steel open hearth of regenerative chamber and sediment chamber, soaking furnace, glass melting furnace, refractory silica brick materials and ceramic firing kiln and kiln of the vault and other supporting parts. Used in the construction of regenerative chamber, chute, combustion chamber, coking chamber, furnace roof etc. parts of the coke ovens. Also used in hot blast stove of high temperature bearing parts and the roof of acid open hearth furnace. Technical Index: Item Silica Brick for Coke Oven Sole, Walls Other Positions SiO2 % 94.5 94.5 A12O3 % 1.0 1.0 Fe2O3 % 1.0 1.0 CaO % 2.5 2.5 Apparent Porosity % 22 24 True Density g/cm3 2.32-2.33 2.32-2.34 Cold Crushing Strength MPa 40 35 Refractoriness Under Load (0.2MPa) 1650-1660 Residual Quartz % 0-1 Permanent Linear Change (1450 *2h) % 0-0.2 0-0.2 Thermal Expansion Rate 1000 % 1.28 1.30 Refractoriness 1710
Description The low Porosity fireclay Bricks are made of super calcined flint clay and calcined bauxite, With high Pressure formed and high temperature sintered. Due to its low apparent porosity, Strong resistance to erosion and high refractoriness under load,They are wildly used in Glass kiln,Blast furnace, Metal mixer Furnace,Hot metal mixer ladle,Coke dry quenching devices , etc. Specifications 1. Low bulk density, low thermal conductivity, good thermal performance. 2. Refractory category allow direct contact of fire, suitable for various atmosphere 3. Good integrity with furnace lining, long service life, easy operation, could be shaped freely
Red Brick/Wall Brick Building Material Sizes 240x240x115 240x200x115 200x90x53 240x115x53 0,16$-0,29$ Ship to everywhere , contact for pictures and more information if your quantity is many, it can be cheaper
fireclay insulation brick high alumina insulation brick mullite insulation brick bulk density: 0.5-1.0 g/cm3
SiO2: 95% for coke oven, blast furnace, glass furnace.
Al2O3: 42-99% refractoriness min 1790 bulk density: 2.1-3.0 apparent porosity: 24-17%
Mono Aluminium Dihydrogen Phosphate(MAPP) : 1.Properties: Aluminium dihydrogen phosphate is a type of colorless and odorless but extremely sticky liquid, freely soluble in water and solidifiable at normal room temperature.It has strong binding force in liquid or solid states and good resistance to peeling, high temperature, vibration and hi-temp air stream in addition to good infrared absorbability and insulativity. 2. Product application It is mainly used as binder and curing agent in the production of hi-temp refractory materials for kiln, spray paint, Fire clay, casting and foundry industry. It is a type of colorless and odorless but extremely sticky liquid, freely soluble in water and solidifiable at normal room temperature 3.Aluminium dihydrogen phosphate chemical examination report Item Standard Appearance Colorless Liquid White Powder P2O5 % 33±1 66±2 Al2O3 8±0.5 16±1 Iron oxide (Fe2O3)% 0.02 0.02 pH value 1.4~2.6 1.4~2.6
Silica brick is a refractory product containing SiO2 as a main component. Its SiO2 content is generally not less than 93%. Silica brick is an acidic refractory material. It has strong resistance to acid slag and good resistance to oxides such as CaO, FeO and Fe2O3. However, it has poor resistance to alkaline slag erosion and is easily oxidized by Al2O3, K2O and Na2O. Destruction by the action of matter. The softening temperature of the silicon brick load is as high as 1640~1680�°C, and the long-term use volume is stable under high temperature. However, silica bricks have poor thermal shock resistance and high refractoriness. When using silica bricks, pay attention to two points: when the silica brick is at 200~300�°C and 573�°C, the volume suddenly expands due to the crystal transformation. Therefore, the temperature rise below 600 �°C in the oven should not be too fast, when it is cooled to below 600 �°C. Dramatic temperature changes should be avoided; as far as possible not in contact with the alkaline slag. Application Coke oven, Hot blast stoves, Crown or Superstructure of glass furnace.
Magnesite brick, the content of magnesium oxide is more than 90%,periclaseas the main crystal phase of basical refractory brick. Magnesite with high temperature refractorness, high begining temperature of softing under loading,good alkali resistance of slag. According to differnence of the production technology and raw materials,it is names general magnesite brick and fused magnesite brick. Magnesite brick is mainly used for open hearth furnace,bottom and wall of the EAF,conventer, high temperature tunnel kiln,cement kiln,lime kiln, glass furnace regenerator. Any interests, get back to me at whatsapp008618848875625
High Alumina Bricks are produced with select bauxite chamotte as main raw material, fired at 1450-1470 �°C by advanced process with strict quality control. High Alumina bricks have great features like high temperature performance, great corrosion and wear resistance, high bulk density, low iron content, etc. High Alumina bricks are extensively used in mining, metallurgy, cement, and chemical, refinery and refractory industries. These bricks are used in all kinds of industrial furnaces and high temperature areas to prolong the lives of furnaces. High alumina bricks have high refractoriness, good acid and alkali erosion resistance, high temperature strength, thermal shock stability is good wait for an advantage, widely used in metallurgy, petroleum, chemical industry, building materials, thermal technology equipment mechanical processing, military industry and other industries.
AZS brick use high purity zircon, alumina and silica as its raw material. Our fused AZS blocks mainly inclue model AZS-33#, AZS-36#, and AZS-41#. the different models applicated in different parts of furnaces. AZS brick 33#, a normal refractory material, with the features of very good melting glass resisting, which seldom produces stone or other faults, and has little possibility to produce bubbles, widely used in glass Industrial furnace. AZS brick 36# has more free baddeleyite crystals in chain structure and less vitreous phase, which further improves the corrosion resistibility and reduces the potential defects in glass, so it is recommended to be used in sections where glass flow is faster and temperature is higher, such as melter sidewall, paving, doghouse, etc. AZS brick 41# has the most free baddeleyite crystals among the fused cast AZS families, which are evenly distgributed within the block. Its corrosion resistibility is the best and thus it is usually recommended to be used in the most demanding positions to balance the furnace life.
AZS brick use high purity zircon, alumina and silica as its raw material. Our fused AZS blocks mainly inclue model AZS-33#, AZS-36#, and AZS-41#. the different models applicated in different parts of furnaces. AZS brick 33#, a normal refractory material, with the features of very good melting glass resisting, which seldom produces stone or other faults, and has little possibility to produce bubbles, widely used in glass Industrial furnace. AZS brick 36# has more free baddeleyite crystals in chain structure and less vitreous phase, which further improves the corrosion resistibility and reduces the potential defects in glass, so it is recommended to be used in sections where glass flow is faster and temperature is higher, such as melter sidewall, paving, doghouse, etc. AZS brick 41# has the most free baddeleyite crystals among the fused cast AZS families, which are evenly distgributed within the block. Its corrosion resistibility is the best and thus it is usually recommended to be used in the most demanding positions to balance the furnace life.
High Alumina Bricks are produced with select bauxite chamotte as main raw material, fired at 1450-1470 �°C by advanced process with strict quality control. High Alumina bricks have great features like high temperature performance, great corrosion and wear resistance, high bulk density, low iron content, etc. High Alumina bricks are extensively used in mining, metallurgy, cement, and chemical, refinery and refractory industries. These bricks are used in all kinds of industrial furnaces and high temperature areas to prolong the lives of furnaces.
The Al2O3 content is more than 55%, and is calcined from a high-content alumina raw material such as a silicone raw material or a bauxite. High heat resistance and high temperature resistance at 1770 C and above. Has good slag resistance, mainly used in the masonry of steelmaking electric furnace, glass furnace, cement rotary furnace and so on. Characteristics of High Alumina Brick Price: 1.Refractoriness: More refractory than refractory clay bricks and semi-silica bricks, up to 1750-1790C, belonging to high-grade refractory materials. 2. Load softening temperature: Since the high aluminum has a high Al2O3 content, a low impurity content, and a low formation of the molten glass body, the fire-resistant softening temperature is higher than that of the refractory clay brick. However, since the mullite crystal has not yet formed a network structure, the load softening temperature is lower than the load softening temperature of the silica brick. 3. Slag resistance: High Al2O3 has high Al2O3 content, close to neutral refractory material, and can resist the erosion of acid slag and alkali slag. Because it contains SiO2, the resistance to alkali slag is less than acid resistance.
Magnesia-chrome brick is a high-level refractory product material ,which contains MgO and Cr2O3 as the main components, periclase and spinel are the main mineral components. This type of brick has high refractoriness, high temperature strength, strong resistance to alkaline slag, excellent thermal stability, and certain adaptability to acidic slag. The main raw materials for the manufacture of magnesia chrome bricks are sintered magnesia and chromite. The purity of the magnesia raw material should be as high as possible.
Features 1.High refractoriness 2.Good abrasion and creep resistance 3.High density Applications It is mainly used in areas that require high abrasion and temperature resistance, such as gliding rail bricks in steel pusher metallurgical furnaces, the tapping platform (tapping spout) style walking beam furnaces, and also as the interior for destructors.
Plant Introduction Sinometal refractory engineering Co., Ltd. is a modern comprehensive enterprise consisting of scientific research, manufacture and trade. Industrial products of the company are mainly magnesia refractories. Products of the company: The company possesses domestic advanced production line of refractories used in metallurgy industry; more than 160 sets of extensive manufacturing facilities; and more than 30 sets of checkout equipment. The company's annual output of magnesia carbon brick, alumina magnesia carbon brick and aluminium carbide brick and so on is 70,000 tons Quality advantages: All products of the company are in accordance with national standard as well as the enterprise's standard, and has got ISO9001 Quality Management System Certification and ISO14001 Environment Management System Certification. Scientific and technical advantages: The company invested a large sum of money to built the building of engineering technology center which covers an area of 5,000 square meters in 2012.The company's capability of scientific research and development is abundant. high refractoriness Brick brief introduction Magnesite Carbon brick is a kind of basic refractory which is made from magnesite, graphite as raw material, resin as binder, with high pressure moulding and low temperature treatment. As one kind of compound refractories, it make magnesite good slag erosion risistance and graphite high thermal conductivity and low dilatability mixed together. Thus BOF Brick has features of high refractoriness, good thermal shock resistance,erosion resistance, and has good performance in I&S industry, including BOF, EAF, LF. basic refractory brick series have the advantages of good performance, long life and low cost. And long supply experience can make sure that we can give our customer total solutions Alumina Magnesia Carbon brick has same production process, the main raw materials are fused alumina or bauxite, so it has better strength and refractoriness under load, but the slag resistance is not as good as magnesia Carbon bricks.
Andalusite is a superior high-alumina refractory material, with high temperature stability, chemical resistance, heat resistance, strong impact resistance, high thermal mechanical strength characteristics. The color of andalusite is gray, pink and red-brown. Heating to 1300, Andalusite will turn into mullite, which is one of the raw materials to produce advanced refractories.
Magnesia chrome brick is an alkaline refractory product, which is made of periclase and magnesia chrome spinel, and is fired at 1600~1800 °C in an oxidizing atmosphere. It can also be made into non-burned brick by chemical bonding agent such as water glass. According to the raw materials and process characteristics of the products, it can be divided into silicate-bonded magnesia-chrome bricks, direct-bonded magnesia-chromium bricks, re-combined magnesia-chrome bricks, semi-recombined magnesia-chrome bricks, pre-reacted magnesia-chrome bricks Casting magnesia chrome bricks.
With the breakthrough of the suspension preheating and pre-decomposition technology in the cement industry and the increasing size of the equipment, the heat load of the kiln is significantly increased, the rotation speed is accelerated, the alkali corrosion is severe, and the lining life and equipment operation cycle are shortened, thus the requirements for refractory materials. More demanding. Its performance advantages are mainly manifested in: 1. High refractoriness under load and excellent high temperature resistance; 2. High strength, abrasion resistance, and easy to peel off and erosion; 3. Low thermal conductivity and good heat insulation effect; 4. Strong flexibility and heat resistance Excellent seismic performance; 5, moderate density, reduce the cylinder load.
