Chumni Bowl The coals are used to heat the shisha tobacco. They are typically made of natural materials, such as coconut shells or lump charcoal. There are many different types of coals available, so you can choose ones that burn for the desired amount of time and produce the desired amount of heat.
Shisha Foil Paper Here Are Some Tips For Using Shisha Foil Paper: Use A Single Layer Of Foil. Poke Small Holes In The Foil With A Fork Or Skewer. Place The Foil Over The Shisha Bowl And Secure It With A Rubber Band. Place The Coals On Top Of The Foil. Adjust The Heat Of The Coals As Needed.
Charcoal It Takes Plenty Of Heat And A Method For Building And Maintaining A Fire To Camp, Cook Outside, Or Survive A Long Winter In A Cabin. You May Wonder If You Can Burn Charcoal Directly In The Firepit When Building A Fire Or Cooking Food Over Your Homemade Fire. Here The Types Of Charcoal Charcoal Coconut Charcoal Bbq
Air conditioner and refrigeration compressors.General maintenance and installer
Centrifugal, inline, duct and wall, ceiling ventilation exhaust fans.Exporter
Oil & gas equipment, HVAC, industrial burners, valve, pipe & fittings, chillers, low-temperature gas equipment, steam equipment, heaters, absorption products, power generation & building materials.Exporter
At UTS we source and sell Charcoal with impeccable quality, our charcoal is a lightweight black carbon residue produced by removing water and other volatile constituents from Plant materials. we produce charcoal by slow Pyrolsis the heating of wood in the absence of Oxygen. This process is called Charcoal Burning. The finished charcoal consists largely of carbon and can be used for various applications
Anode butts are the residual electrode left in the electrode holder at the end of electrolysis with prebaked carbon anodes. The anode carbon is being consumed by ohmic resistive heat and electrolytic oxidation. However the part of anode just above the melt is being continuously subjected to high temperature reactions with fluoride melt and atmospheric oxidation, which ultimately results in impurities left in the discarded anode butts.At the end of their use, the left over part of the anode (called butts) are crushed and recycled to produce new anodes. However, while recycling the butts the built-up of sodium concentration is closely checked and controlled in order to avoid harmful effect of excess sodium in newly formed anodes. Good quality anodes should be oxidation resistant in gaseous environment in order to minimize oxidation on the expose surface (C + O2 2CO) [19] Price of Product (USD) : 300 Product Origin : MERCO W.L.L BAHRAIN
Bitumen penetration grade 60/70 means the penetration value is in the range 60 to 70 at standard test conditions which commonly used as a Paving Grade. Bitumen is applicable for the production of hot mix asphalt for bases and pavements and for road construction.Penetration Grade Bitumen supplied by MERCO Bahrain. Its penetration grade ( the measure of bitumen hardness) is between 60 to 70. Bitumen is specified by the penetration and softening point test.Penetration determines the hardness of bitumen by measuring the depth to which a standard loaded the needle will vertically penetrate in 5 seconds, in a sample of bitumen maintained at a temperature of 25 degrees Celsius. Price of Product (USD) : 503 Product Origin : Merco W.L.L Bahrain Key Specifications / Special Features : Test Name Test Method Unit Result Specific Gravity @25°C ASTM D70 kg/cm³ 1.01-1.06 Penetration @25°C ASTM D5 mm/10 60/70 Softening Point °C ASTM D36 °C 49/56 Ductility @25°C ASTM D113 cm 100 min Loss on Heating (wt%) ASTM D6 wt% 0.2 max Drop in Penetration after heating % ASTM D5-D6 % 20 max Flash Point °C ASTM D92 °C 232 min Solubility in Trichlorethylene ASTM D2042 wt% 99 min Spot Test A.A.S.H.O.T102 Negative Minimum Order size and packgaing detail we will provide both 20FT as well as 40FT Containers (200 Liter per drum both open as well as closed top Drums), also in 1 MT flexi bags. Steel Drum Sizes Drum Size 200 kg Drum Height 980mm Diameter 520 550mm Thickness 0.6 –0.8mm
Bitumen emulsion is a mixture of fine droplets of bitumen and water. But as the bitumen is a petroleum product it doesn’t mix with water and as it is sticky in nature, it doesn’t easily gets disintegrated into fine droplets. To overcome this problem an emulsifier is used. Emulsifier can be defined as a surface-active agent. Emulsifier keeps the bitumen in its fine droplet state by disallowing it to mix with other droplets. As the droplets are very fine they suspend in water. Therefore, bitumen emulsion is a dispersed liquid consisting of three products, i.e. water, bitumen and emulsion. Bitumen emulsion is a mixture of fine droplets of bitumen and water. But as the bitumen is a petroleum product it doesn’t mix with water and as it is sticky in nature, it doesn’t easily gets disintegrated into fine droplets. To overcome this problem an emulsifier is used. Emulsifier can be defined as a surface-active agent. Emulsifier keeps the bitumen in its fine droplet state by disallowing it to mix with other droplets. As the droplets are very fine they suspend in water. Uses Cationic emulsions may be used at ambient temperatures with aggregates, which need not be completely dry. Emulsions are less hazardous to use and can be applied in a wider range of conditions. Advantages a) Cationic emulsions may be used at ambient temperatures with aggregates, which need not be completely dry. b) Lower costs are incurred due to a considerable saving on fuel for heating purposes. c) Operating at lower temperatures for cold mixing gives a greater margin of safety, even though these emulsions may contain fluxing oil. d) Not only may cold mix be stockpiled for long periods, but it may also be packaged in small containers and stored. This facilitates the treatment of very small areas quickly, cleanly and economically. Disadvantages A regular water supply is required and this can be a great problem in very hot countries, where water can be in very short supply. Price of Product (USD) : 432 Product Origin : Merco W.L.L Bahrain Key Specifications / Special Features : Type Viscosity @25°C Penetration & Solubility Residue Tack Coat K1- 40 25 Max 60- 200 & (97.5) 38% Rapid Setting RS-1K 20-50 60- 200 & (97.5) 50% Rapid Setting K1-60 -NA & (97.5) 57% Rapid Setting CRS-160- 200 & (97.5) 60% Rapid Setting CRS-2-60- 200 & (97.5) 65% Rapid Setting K1-70NA & (97.5) 67% Medium Setting K2-NA & (97.5)57% Medium Settng CMS 2-60- 200 & (97.5) 65% Slow Setting K3 20- 100 60- 200 & (97.5) 56% Slow Setting CSS-1 20- 100 60- 200 & (97.5) 57% Minimum Order size and packgaing detail 16.00(=/-3%) Metric tons per 20 Foot Container. 200 kgs(+/-3kgs) in one drum.Total no of drums in 1 container 80
