V.c.i. Film

Masking Tapes : Masking Tapes Manufacturers starting from general purpose applications to high temperature requirements of powder coating masking. Both paper and filmic materials are available for these applications. They have been designed to perform under the most demanding conditions and are resistant to strong solvents and paints. Pressure Sensitive Tape made of a thin and easy-to-tear paper, co-polymer films, and coated with suitable adhesive. It is used mainly in painting, to mask areas that should not be painted. The adhesive is the key element to its usefulness, as it allows the tape to be easily removed without leaving residue or damaging the surface to which it is applied. The tape is available for several temperature range depending on the application. Below listed are the details of tape availability with reference to the application. Backing Crepe Paper Temperature Upto 180° C Adhesive Rubber Features Residue Free removal Applications : Body Shop Painting in Automotive Applications Masking in PCB Manufacturing Process

Masking Tapes : Masking Tapes Manufacturers starting from general purpose applications to high temperature requirements of powder coating masking. Both paper and filmic materials are available for these applications. They have been designed to perform under the most demanding conditions and are resistant to strong solvents and paints. Pressure Sensitive Tape made of a thin and easy-to-tear paper, co-polymer films, and coated with suitable adhesive. It is used mainly in painting, to mask areas that should not be painted. The adhesive is the key element to its usefulness, as it allows the tape to be easily removed without leaving residue or damaging the surface to which it is applied. The tape is available for several temperature range depending on the application. Below listed are the details of tape availability with reference to the application. Backing Crepe Paper Temperature Upto 70° C Adhesive Rubber Features Residue Free removal Applications General Purpose Painting Holding in Furniture Industry

Corona resistance polyimide films ,not only with ordinary polyimide film electrical properties, good heat resistance and resistance chemicals, but also with the super corona resistance and good thermal conductivity performance, mainly apply to sintering electromagnetic winding wire ,traction motor, wind generators, and the special motor turn-to-turn insulation and heat insulation, the heat resistance level is a class C. The technical requirements: 1. Type CR type: Corona resistance polyimide film without any coating FCR type: Corona resistance polyimide film with F46 single side coating FCRF type: Corona resistance polyimide film with F46 double side coating 2. Appearance its appearance is golden brown, translucent, the surface is bright and clean, no wrinkles, tear, particles, bubble, pinhole and foreign material defects. Its edge is tidy, and without damage. 3. Thickness and allowable deviation Model CR type FCR type FCRF type Thickness(um) 25 38 50 Allowable deviation(um) 2 3 3 Note: coating thickness may be based on customer demand in 5 ~ 12.5 um range regulation. 4. Width and allowable deviation Width may cut according to the customer request within 600 -1050 mm. Each volume length is for 500-1000 m; Each volume joints for final product are not more than three, the proportion of volumes with joints vs the total volumes number in the one order is not more than 25%,the shortest length is more than 300 m; Single plate or roll products joint numbers are not more than three, the shortest length is more than 300 m. FCR type and FCRF type using thermal bonding lap. 5. Film marks: -Every single volume label marked: batch number, specification, net weight;Every single plate or roll labeling: specification. -Package should have obvious and firm mark; -The format of the packing cases is confirmed by purchase order related terms. Serial Number Type CR FCR FCRF 1 Corona resistance life (h) 1 KV voltage, frequency 20 KHz temperature 90 2 pulse rise time 400 ns Y80 Y80 Y80 2 Industrial frequency electric intensity (v/um) Y200 Y120 Y100 3 Surface resistivity 1X1014 1X1014 1X1014 4 Volume resistivity 1 1X1010 1X1010 1X1010 5 Relative permittivity (48-62 Hz ac) 3.2 0.4 3.2 0.4 3.2 0.4 6 Dielectric power factor (48-62 Hz ac) 13.5X10-3 13.5X10-3 13.5X10-3 7 Tensile strength (Mpa) : Y135 Y80 Y80 8 Elongation at break (%) Y40 Y40 Y40. 1. Testing method: According to the ICE62068-1-2003/ GB /T13542.6-2006 "electrical insulation, part 6," Polyimide film for electrical insulation regulation experimental method. 2. Film packaging: Film roll with plastic film packaging, outer with shockproof foam cushion packaging, and support in place in the package overhead, make the film in the transportation conditions often get fully protected without damage, each volume end article sticker marking. 3. Dust is strictly prohibited in the packing box internal. 4. Film should be stored in a dry and clean indoor, film roll to be supported in the box, placed suspended and not be erected. It should not be close to the fire, central heating or exposed to direct sunlight. 5. Products should avoid damp and mechanical damage in the storage and transport. 6. Film storage period is for two years after COA issued date. Expired films are still available after again qualified according to the product standards inspection.

I description: Polyethylene anticorrosive tape is cold applied tape coating system for corrosion protection of oil, gas, petrochemical, and waste water underground or overhead pipelines. The inner-layer tape shall be applied after the primer and before the outer-layer tape by hand or with a wrapping machine structure The specification of the tape consists of two layers, adhesive layer and film backing Adhesive: butyl rubber Outer layer: special blend of stabilized polyethylene Iii Features Excellent adhesion to pipe and self Resistant to uv Can be applied over a wide temperature range Good conformability and consistent uniform thickness Easily applied with no special equipment Compatible with common pipe coatings Excellent resistance to cathodic disbonding Meets astm d 1000 standard Cold applied Technical datas: Inner wrap tape: xunda-t 100 series TypeT-150T-165T-180 Total thickness0.51 mm0.65 mm0.80 mm Polyethylene film0.31 mm0.34 mm0.39 mm Synthetic adhesive0.20 mm0.31 mm0.41 mm Elongation at break„d 400% Tensile strength60 n/cm61.2 n/cm63 n/cm Yield strength35.5 n/cm42.3 n/cm45.5 n/cm Peel adhesion to primed pipe21.2 n/cm26.5 n/cm33.2 n/cm Dielectric strength35 kv/mm45.8 kv/mm48 kv/mm Cathodic disbandment0.24 in radius 6.4 mm Volume resistivity2.5 x 1012 ohm.M Water vapor transmission rate „t 0.1gm/m2/24h Water absorption rate < 0.06% Recommended application temperature -5 to +600 c Max serve temperature-40 to + 800 c ColorBlack Available roll size (width x length)2" to 9" x 50 to800 feet. Paper cartons packing with waterproof membrane.

You can measure pressure, pressure distribution and balance. (Mono-sheet type: 110+/-5u; two-sheet type: A-Film: 90+/-5u ; C-Film: 90+/-5u). Red patches appear on prescale when pressure is applied. The color density changes according to pressure level. (density: 0.1~1.4) six kinds of prescale are supplied to comply with demands to measure a wide pressure range. (0.2~300mpa.).

Ldpe posted industral film 1. Commodity: ldpe film 2. Origin: usa or europe 3. Quantity: as much as you have every month on monthly basis 4. Speicification: A) dry and clean B) baled or on roll C) natural color D)singled ldpe film from industry wast for packing, not mixed hdpe, pp, pve film etc. E))no life garbage 5. Price: under discussion 6. Payment: 30% / 70% against b/l or under discussion 7. Port of destination:qingdao, china 8. No middlemen or agents. Only direct suppliers Compacted into secure bundles with a minimum weight density of 10 lb./cubic foot and load about 18 ton per container

Quick Details Material : PVC Type : Stretch Film Usage : Packaging Film Hardness : Soft Transparency : Transparent Place of Origin : Bangkok, Thailand Please let me know if you are interested in our material. It is definitely in a good quality with a reasonable price. If our product could be of your interest, please let mek now. I would be very happy to provide you with the further information and its quotation. Also, if you wish to receive our product sample in order to prove its quality before making any further decision, please let me know and informe of your company mailing address along with its reachable phone number and the contact person in order to contact with the courier agent.

Special adhesive film is made from the mixture of some petrochemicals. It makes full use of the permeability of this substance to penetrate into the micro-pores of the surface of the objects , and the characteristics of its cohesion to adhere tight to the objects . It is characterized by : (a)Can be attached tight onto the surface of the objects . (b)Can carry the weight . (c)Waterproof and can withstand high temperature -10¢J--80¢J . (d)Is very easy to be peeled off . (e)Environmental and economical , can be reused for a great number of times (but should be noted that the surface of the objects and films are both clean before pasting). In fact , the film can be used in a very wide range , such as : adhesive tape (single or double side), passes, stationery, childrens toys, printing posters, billboards.etc , and so on . Wherever in the kitchen , bathroom, bedroom , office , exhibition places and even in the freezer, film can be fully used . If we can make the most of our imagination and creativity, the film can practically make our daily life more convenient and comfortable . 21cmX31cm/piece.

The POF environmental shrink film is non-toxic, transparency,hign shrinkage rate, good sealing character, high gloss surface,good toughness, heat evenly, adapt to high antomatic.with these advantages, it become the new generation of traditional PVC shrink film, POF C-3 widely used in food,medicine,beverage,alcohol, electrical products,electronical products,tools, the outer package of daily necessities.especially the super shrinkage character., all made it to be the best package material. Summarize all Advantages of POF shrink film: 1. high transparency,good sealing. 2. high flexible,convinience to use 3. high shrinkage ,up to75% 4. high heat sealing and intensity,adapt use by hand, half automatic and high-speed automatic package, 5. high cold resistance, keep the flexibility belowú¡50íµ,adapt to storage and transport in cold weather. 6. non toxic,can packing food 7. prevent damp and dust 8. low package cost,better than paper box and other materials 9. can used in print after corona. Paper box.

The POF environmental shrink film is non-toxic, transparency,hign shrinkage rate, good sealing character,, high gloss surface,good toughness, heat evenly, adapt to high antomatic.with these advantages, it become the new generation of traditional PVC shrink film, POF C-3 widely used in food,medicine,beverage,alcohol, electrical products,electronical products,tools, the outer package of daily necessities.especially the super shrinkage character., all made it to be the best package material. Summarize all Advantages of POF shrink film: 1. high transparency,good sealing. 2. high flexible,convinience to use 3. high shrinkage ,up to75% 4. high heat sealing and intensity,adapt use by hand, half automatic and high-speed automatic package, 5. high cold resistance, keep the flexibility belowú¡50íµ,adapt to storage and transport in cold weather. 6. non toxic,can packing food 7. prevent damp and dust 8. low package cost,better than paper box and other materials 9. can used in print after corona. Paper box