Differences between Spray Paint and Electrostatic Powder Coating:
1. The effect of Spray Painting is mirror. The effect of Powder Coating is mostly frosted surface with small holes.
2. The paint is thinner than the powder. The paint is about 30 microns in size. The powder particles are about 60 microns.
3.The smell of paint is harmful to health. Small powder pollution, small and environmental impact on workers' health.
4. Paint is volatile matter, so the Curing temperature in the Curing Heating System is below 150 degrees Celsius. The temperature of the Powder Spraying workpiece in Curing Oven needs to be between 180 and 220 degrees Celsius.
5. The same grade of Powder is cheaper than lacquer.
6. The strength of the powder is better than the ordinary paint.
7. Powder Spraying can be in place once. And the powder that falls into the groove in the Spray Room can still be used repeatedly to save cost. Hebei Hanna technology CO., LTD. 's Fast Automatic Powder Color Changing System can change color rapidly for 15 minutes. It saves manpower and time. This is really good for you if you have more color on your workpiece to change. And the Big Cyclone can achieve 99.2% recovery. It's economical and environmentally friendly.
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
PC natural 100% pure pc without any coating MATERIAL: PC natural 100% pure pc without any coating CATEGORY: PC TYPE: Natural SPECIFICATION: Separate 25 kg bag and Mark per month 78 mt 100% pure pc without any coating ,post Industrial materials Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 1450$ - 1700$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days Our Commitment We are committed to delivering in accordance with the quality given, source and licensed in the field of scrap transportation. 2Lians always for the purpose of satisfying customers on the criteria of sustainability and fairness through high work efficiency
Epoxy Finish Paint is two-component, polyamide adduct cured, General Purpose Air drying Epoxy Coating. Its Excellent substitute to Enamel.
Two component, acrylic aliphatic polyurethane coating. Offers excellent gloss and colour retention. It is used for subtracts as steel, aluminum, glass-fiber, plywood etc.
BARILAC barrier coatings are the most suited sustainable solution to replace polycoated laminated board, waxcoated, PVDC coated etc all non sustainable alternatives. Barilac barrier coat is recommended for paper cup, trays, foodtrays, pizza boxes, ice cream cartons etc. The special product features are. - Low COBB - Good oil and grease resistance - Good Moisture Vapour Transmission rate - Good heat sealing performance - Good water resistance - Low odour - FDA compliance
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Supplier: Food and agricultural crops , legumes , vegetable, fruits , fodders , herbs , grains , tomato paste , dried tomatoes , potato , sweet potato , bananas, dates.
men's, women's and children's clothing, fabrics and textiles, medical supply, household tools and equipment, paints and construction supplies, foliar fertilizers, plant nutrition , micro elements, Â fertilizers, plant health, herbs
Services: International trade
Water Based Coatings - Primers, Gloss & High Scuff - High Gloss/High Slip - Duct Gloss & Matt - Specialty Coatings - Soft Feel / Satin / Neutral / Super Matt
Supplier: Food grade talc for confectionery, talc ip, bp, ultra fine talc for automobiles, talc, soapstone, steatite for plastics and paint, calcium carbonate powder for food, confectionery and ultra fine calcite powder, dolomite powder, china clay powder, quartz lumps and powder, silica sand, river sand and mica
Buyer: Barytes powder or barite , calcined clay, food chemicals
