There are many industries in the leading refractory market who is constructing a lot of alumina mortars in India but Imperial World Trade continues leading of others due to its high quality and regular production of its products. We manufacture 70 K mortar using special quality of raw material stuff in our tremendous plant where state of the art of technology is functioned.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
25/50 Kg BAG & 01 Ton Jumbo bag Refractor Castable are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer wide range of refractory castable such as : Conventional Castable Super Castable, Fire crete, HEAT - A Castable, HEAT- K Castable Low & Ultra Low cement Castable MON -45, MON-60, MON-70, MON-80, MON-90 Gunning Castable MONGUN-45, MONGUN-60, MONGUN-70 Insulating Castable INSUCAT-9, INSUCAT-11, INSUCAST-13, INSUCAST-15
Incoloy Alloy 908 is a high-temperature, high-strength, and highly corrosion-resistant alloy composed of elements such as nickel, chromium, molybdenum, and iron. It is a single-phase austenitic alloy, typically formed by casting and forging. Chemical composition: The chemical composition of Incoloy Alloy 908 is composed of elements such as nickel, chromium, iron, molybdenum, vanadium, manganese, tantalum, silicon, carbon, phosphorus, and sulfur. Nickel content is 40-45%, chromium content is 20-23%, iron content is 16-19%, and molybdenum content is 8-10%. Mechanical properties: Incoloy Alloy 908 has excellent high-temperature and high-strength performance. Its tensile strength is 135 ksi (930 MPa) (minimum), yield strength is 70 ksi (480 MPa) (minimum), and elongation is 25% (minimum). Physical properties: The density of Incoloy Alloy 908 is 8.14 g/cm�³, the melting point is 1338�°C (2440�°F), the thermal conductivity is 11.7 W/m�·K (100�°C), and the coefficient of thermal expansion is 13.7 �¼m/m-K (20-100�°C). Corrosion resistance: Incoloy Alloy 908 has excellent corrosion resistance, especially in high-temperature, high-pressure, and highly corrosive environments. It can withstand the corrosion of corrosive media such as sulfuric acid, hydrochloric acid, nitric acid, and fluoride, and can resist chloride stress corrosion cracking (SCC). The international standard designations for Incoloy alloy 908 include UNS N09908 and W.Nr. 1.4876. There are also corresponding standards and specifications in different countries and regions, such as AMS and ASTM standards in the United States, EN standards in Europe, and JIS and JPI standards in Japan. Here are the specific standards and designations for Incoloy alloy 908 in different countries: United States: AMS 5545, AMS 5546, AMS 5547, AMS 5549, ASTM B408, UNS N09908 Germany: DIN 17752, DIN 17753, DIN 17754, W.Nr. 1.4876 United Kingdom: BS HR 6 Europe: EN 10095 Japan: JIS H4551, JPI-SB46 We can provide the following the form:Incoloy alloy908 coil; Incoloy alloy908 strip;Incoloy alloy908 plate; Incoloy alloy908 sheets; Incoloy alloy908 tube; Incoloy alloy908 pipe;Incoloy alloy908 flat; Incoloy alloy908 bar GB:HR 6/JIS:H4551/UNS:N09908/W.Nr:1.4876
Supplier: HFI, HFK, CFI , high alumina bricks ranging upto 70%, fireclay bricks with related mortars and castables, glass bottom tanks, tiles and hanger, shoulder bricks according to customer drawings
Supplier: High alumina brick, is 6, is 8, bp sets, insulation bricks (hfk), cupola bricks, castable, mortar, bfa, wfa, white heat a, white heat, k monolithic (castable), sillimanite bricks, ramming mass, calcium silicate block, acid proof bricks, ceramic fiber blanket all type refractories product
Services: Transport, inspection
Fly ash brick Product : fly ash bricks Size : 230x110x70 mm Weight : 3.5 kgs Color : grey Raw materials used : fly ash, lime, gypsum, sand water & bonding chemical Manufactoring method:automatic hydraulic press with 70 ton pressure Properties High compressive strength Durable Low water absorption Less consumption of mortar Economical & eco-friendly Low energy consumption No emission of green house Gases 7500/container
Excellent thermal resistance Fireproof Rock Wool Board Rock Wool Insulation products are made from natural mineral wool such as basalt and dolomite. Density Thickness kg/m3 mm 60 50 70 80 100 150 / 75 50 70 80 100 150 / 80 50 70 80 100 150 / 100 50 70 80 100 150 / 120 30 40 50 80 100 / 130 30 40 50 70 80 100 150 30 40 50 70 80 100 180 30 40 50 70 80 100 200 30 40 50 70 80 100 PRODUCT FEATURES Rock Wool Board products are made from natural mineral wool such as basalt and dolomite. The natural rock are melted into melts in cupola at a very high temperature about 1500. The highest application temperature is 650. it has characters: heat insulation sound reduction, fireproof, waterproof and so on. Fire Doors Rock Wool Board advantages: - Excellent thermal resistance - Non-flammable - Easy to install - High sound absorption material - Easy handling and installation - Attractive aluminum appearance - Water-repellant - Resistant to ageing - Marine certified Application of Rock Wool Board: 1. Used for fire protection, thermal insulation in construction and building, commercial and residential buildings. 2. Used for sound absorption in roofing, celling, external wall, partition wall and floating floor. 3. Low density Environment Friendly Rock Wool Board suitable for roof and wall in the building Properties Value Density 60-150 Kg/m3 Shot content (particle diameter â?¥0.25mm), % â?¤12.0 Average fiber diameter, μm â?¤7.0 Density tolerance, % +15, -15 Thermal conductivity coefficient (average temperature: 70±2), W/(m. K) â?¤0.043 Thermal load contraction temperature (products with density above 60kg/m3), â?¤ 600 Acidity coefficient mk â?¥ 1.6 Moisture content, % â?¤0.5 Combustion property Non-combustible(A class) Organic material content, % â?¤ 4.0 Water repellence (water-proof), % â?¥ 98 Water absorption (water-proof), % â?¤ 5 Max Application Temperature 650
Transparent tarp K tarp vina co., ltd would like to introduce best-seller pe tarpaulin with detail as following: Materials: imported virgin raw material (hdpe & ldpe) Specifications: • mesh: 3×3 weaves/inch •color: transparent/ milk white color (any color as per customer’s request) •weight: 70 ~ 280 gram /sq. M •size: 3x4m, 4x5m, 5x8m (any size is available) • conner protection: reinforced by pp rope in hem on all ground edges, aluminum eyelets (plastic eyelets) every 1 meter or 3 feet interval (or as per your request). Special corner patch is available. • each piece be packed in a polybag with your insert label, then some pieces be packed into a carton box or bale. Use: Covers for general use, scaffoldings in construction sites, underground sheets, covers for materials roofs, road repair sites, and fences, etc.
Item unit specifications Wn015 wn022 wn028 wn035 wn042 wn056 wn070 wn160 note Md tensile strength [astm d 4595] Kn/m >= 20 30 40 50 60 80 100 160 Cd tensile strength [astm d 4595] Kn/m >= 15 22 28 35 42 56 70 112 Tensile elongation [astm d 4595] % > = 28 Md/cd Average Widths windage % -1.0 Cbr puncture resistance [astm d 6241] Kn>= 1.6 2.4 3.2 4.0 4.8 6.0 7.5 13.0 Pore size o90 (o95) [astm d 4751] Mm 0.08-0.5 Vertical permeability [astm d 4491] Cm/s k x (10-1-10-3) k=1.0-99 Uv resistance strength Retention [astm d 4355] % > = 70(500h) Tear strength [astm d 4533] Kn>= 0.3 0.45 0.5 0.6 0.75 1.0 1.2 1.5 Md/cd Average Physical identification properties Mass per unit area g/m2 120 160 200 240 280 340 400 700 Warp % ± 10 Standard roll width m() 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 Standard roll length m() 300 230 180 150 130 100 90 50 Approx. Loading q’ty per 40’ hq Sq.M 153, 120 117, 392 91, 872 76560 66, 352 51, 040 45, 936 25, 520 Approx load q’ty per 40’hq 56520, strength at 5% elongation, roll length (m) 100, roll width (m) 1-1.4, 2-3.2, standard roll width m( ) 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8
