En 857 1Sc

Supplier: Hydraulic hoses, rubber hoses, suction hoses, braid hoses, spiral hoses, low pressure hoses, high pressure hoses, air tube, sand blasting hose, oxygen tube, oil drilling hose, fiber reinforced hose, textile covered hose, ptfe lined hose, fiber reinforced hose, thermoplastic hose, compact hose, sae 100r4 suction hose, en 854 1te low pressure hose, en 854 2te hydraulic hose, sae 100r6 fiber reinforced hose, sae 100r1at singe wire braid hose, sae 100r3 hydraulic hose, sae 100r5 textile covered hose, sae 100r14 type a (ptfe lined hose), en 854 3te fiber reinforced hose, 2-wire braid hose sae 100r2at, en 853 2st/2sn high pressure, en 857 1sc hydraulic hoses, en 857 2sc hydraulic hose, en 853 1st/1sn hose, sae 100r13 four spiral wire hose, sae 100r15 six-wire hose, en 856 4sp (four spiral), sae 100r12 four wire, en 856 4sh spiral wire hose, sae 100r7 thermoplastic hose, sae 100r8 thermoplastic hose, sae 100r17 compact hose, sae 100r16 compact hose (high pressure)

1SC Compact Type Single Wire Braided Hydraulic Hose CONSTRUCTION: This hose shall consist of an oil resistant synthetic rubber . a single steel wire braid reinforcement, and an oil and weather resistant synthetic rubber cover, available in black with either wrap or smooth finish. ( ) APPLICATIONS: This hose for use with petroleum base and water base hydraulic fluids within a temperature range of -40 to+ 100C.

Hydraulic rubber hoses are used in high-pressure hydraulic systems for control and power supply. They are designed for the main transmission of hydraulic fluids (hydraulic fluids according to ISO 6743-4, except HFD R, HFD S and HFD T fire resistant fluids). For other applications (e.g. compressed gases), always contact Sanshi Rubber's technical department. For water, water-based liquids and air, the maximum working temperature is +70�°C. For air over 17 bar, the hose cover should have pinholes and be additionally protected. Hydraulic rubber hoses are manufactured in imperial sizes with standardized inner diameters. The most popular standards for setting hose requirements are: European standard - EN, International ISO and American SAE. symbols of the standards and the most important data (diameter, working pressure and date of manufacture) are marked on the hose. In addition, the hose may bear a specific name assigned by the manufacturer or the customer. Characteristics of hydraulic rubber hoses Greater flexibility Minimum bend radius is smaller than standard hydraulic hose. Higher pressure parameters Hydraulic hoses with a maximum working pressure higher than standard requirements. This expands the application range of the hose while maintaining a safety factor and the same hose diameter, so there is no need to change it (e.g., make it smaller) or change its type (e.g., from a double braided hose to a spiral hose). Higher temperature parameters Hydraulic hoses have specific operating temperature ranges. For hoses with textile braid (2TE, 3TE types), with compact steel wire braid (1SC, 2SC, 1SN, 2SN) the range is -40C to +100C (peak up to 125C ), and suitable for a certain set of hoses with spiral braid (4SP, 4SH). For spiral hydraulic hoses with constant operating pressure, regardless of diameter (R12, R13, R15), the range is -40C to +121C (peak up to 125C). Sometimes hydraulic systems may operate at temperatures higher than standard hydraulic hoses. If the recommended temperature is exceeded, the rubber begins to lose its elasticity and hardens, and then begins to leak at the end of the hose near the fitting. In this case, a hose with a higher operating temperature range should be used.