Standard taper thread couplers are designed to splice the same diameter bars where one bar can be rotated and the bar is not restricted in its axial direction.It is designed to achieve failure loads in excess of 115% of the caracterisitc strength of grade 500 rebar end.
Transition taper thread couplers are designed to splice different diameter bars where one bar can be roated and the bar is not restricted in its axial direction.
Taper Thread Working Principle:
1.Slice up the end of the rebar;
2.Make the rebar taper thread cutted by taper thread machine.
3.Connect together two taper thread end by One piece of Taper Thread Coupler.
Taper thread position couplers are designed to quickly splice column sections or precision coupling of elements with multiple bars jointed over a short span, such as prefabricated elements, and the closing of small temporary openings.
Taper thread anchor plate provides an alternative to hooked rebar,or an anchor or stop nut for rebar passing through a pile bank or structural steel element.The fraont face of the coupler is generously designed to carry the full tension load of the rebar when the anchor is bearing against concrete or structural steel.
Material: high carbon spring steel, spring steel, stainless steel, alloy steel Compression Spring, Extension Spring : Wire Diameter: 0.2-40.0mm Torsion spring wire diameter :0.2-35mm Surface Finish: black , Zinc, Nickel, silver, golden, tin, powder coating, shot pin Applications: Automotive, medical device, agricultural machinery ,electronics, toy, electric power distribution. Extension spring hook include Germany hook, British hook, Side hook We can customize special design of springs based on your requirement.
Rebar threading machine Rolling screw on rebars and join with couplers New technology compared with welding and binding Nylon bag and wooden pallets. Goods also could be packaged as you required.
Metal braided pump connector are normally are in BSPT (DIN 2999) and NPT treaded pipe ends which are designed to absorbed pump vibration, noise and reduce piping stresses due minor misalignment, these are available in carbon steel / Stainless steel pipes.
Standard taper thread couplers are designed to splice the same diameter bars where one bar can be rotated and the bar is not restricted in its axial direction.It is designed to achieve failure loads in excess of 115% of the caracterisitc strength of grade 500 rebar end. Transition taper thread couplers are designed to splice different diameter bars where one bar can be roated and the bar is not restricted in its axial direction. Taper thread working principle: 1.Slice up the end of the rebar; 2.Make the rebar taper thread cutted by taper thread machine. 3.Connect together two taper thread end by one piece of taper thread coupler. Taper thread position couplers are designed to quickly splice column sections or precision coupling of elements with multiple bars jointed over a short span, such as prefabricated elements, and the closing of small temporary openings. -
YDZTS-40C Rebar Taper Thread Cutting Machine is designed and manufactured by Hebei Yida Reinforcing Bar Connecting Technology Co., Ltd. It is mainly used as a special equipment to make taper thread on the end of the rebar in the processing of rebar connection. Its applicable diameter is from 16 to40. It applies to Grade and level rebar. It has reasonable structure, light and flexible, simple operation, high production efficiency. It is widely used in steel bar end processing of taper thread joints in concrete works .It adapts to a variety of complex construction site environment. The main performance parameters: Processing of bar diameter range: 16mm 40mm Processing thread length: less than or equal to 90mm Processing steel Length: greater than or equal to 300mm Power: 380V 50Hz Main motor power: 4KW Reduction ratio reducer: 1:35 Rolling head speed: 41r/min Overall dimensions: 1000 480 1000 (mm) Total weight: 510kg
Standard taper thread couplers are designed to splice the same diameter bars where one bar can be rotated and the bar is not restricted in its axial direction.It is designed to achieve failure loads in excess of 115% of the caracterisitc strength of grade 500 rebar end. Transition taper thread couplers are designed to splice different diameter bars where one bar can be roated and the bar is not restricted in its axial direction. Taper thread working principle: 1.Slice up the end of the rebar; 2.Make the rebar taper thread cutted by taper thread machine. 3.Connect together two taper thread end by one piece of taper thread coupler. Taper thread position couplers are designed to quickly splice column sections or precision coupling of elements with multiple bars jointed over a short span, such as prefabricated elements, and the closing of small temporary openings. Taper thread anchor plate provides an alternative to hooked rebar, or an anchor or stop nut for rebar passing through a pile bank or structural steel element.The fraont face of the coupler is generously designed to carry the full tension load of the rebar when the anchor is bearing against concrete or structural steel.
1.Adopt thread cold rolling technology, no cutting of rebar parent metal, the strength of threaded end is higher than its parent metal. 2.With spiral lead angle technology, easy to roll thread and ensure higher thread accuracy. 3.Rib peeling device adopts automatic opening-closing mechanism. With high efficiency, need only 20 seconds to finish a threaded end. 4.Be able to process rebar sizes 14-40mm, and max. thread length is 120mm for 16-32mm rebar, and 100mm length for 36-40mm rebar with 7.5kw electric motor. 5.The updated version of AGS-40C and AGS-40Z, the wheelbase and shaft diameter of reducer is bigger than AGS-40 and 40E, so that the machine length is longer than AGS-40C. 6.The height of electric motor and reducer is lower than before, so that it could reduce the center of gravity of the whole machine. 7. Equipped with air compressor. 8. There are 2 machine heads for AGS-50D, 1 is for 14-40mm, and the other for 50mm rebar screw.
Features 1. Hydraulic full-automatic, fast speed. 2. Cutting thread on forged bar with chaser, threading diameter 16-40mm(upsetting M20-M45mm). 3. Strength of the joint is higher than the rebar material. 4. Thread is full enough, max. threading length is 150mm. 6. Thread pitch is from 2.0 to 4.5mm with high accuracy.
YDZTS-40C Rebar Taper Thread Cutting Machine is designed and manufactured by Hebei Yida Reinforcing Bar Connecting Technology Co., Ltd. It is mainly used as a special equipment to make taper thread on the end of the rebar in the processing of rebar connection. Its applicable diameter is from 16 to40. It applies to Grade and level rebar. It has reasonable structure, light and flexible, simple operation, high production efficiency. It is widely used in steel bar end processing of taper thread joints in concrete works .It adapts to a variety of complex construction site environment. The main performance parameters: Processing of bar diameter range: 16mm 40mm Processing thread length: less than or equal to 90mm Processing steel Length: greater than or equal to 300mm Power: 380V 50Hz Main motor power: 4KW Reduction ratio reducer: 1:35 Rolling head speed: 41r/min Overall dimensions: 1000 480 1000 (mm) Total weight: 510kg
