Project name: 3000t penicillin Equipment Name: Finished Producted tankManufacture Code: GB150Specification: ID2000Material: 304
z
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Supplying range as below, 1) tank (pressure vessel) volume: 0.5-5000 cubic meters 2) dimension: we could design diameter and height as per customers' request 3) material: stainless steel (304 or 316l) 4) tank shell thickness: 1.5-8mm5) pressure (mpa): atmospheric pressure-middle pressure (according to the chinese design standard) 6) function: storage or fermentation tank 7) design temperature: -5-80 degree 8) medium: various drinks including wine, beer, fruit juice, and so on. 9) tank surface: the original surface of the stainless steel plate (or polishing if required) 10) operation plate form: we can design the platform if required. 11) mixing: top side or bottom mixing. 12) general accessories(if required): manhole, cip, respirator, sight glass, mixing 13) manufacture standard: chinese pressure vessel design and making standard 14) guarantees inner quality and safety, good looking appearance and function by introducing international advanced large-sized equipment of pulse plasma arcwelder and auto polishing machines and cooperating with international famous finished
FINETANK, the fine tank from Korea, the high quality WATER STORAGE TANKS made of SMC PANELS & STEEL REINFORCEMENTS are available in various capacities and different shapes for various applications (residential/commercial buildings, water treatment plant, fire fighting, irrigation, etc.). FINETANK - GRP SECTIONAL WATER TANK complies to KSF 4811, KSM 3305, KSM-3401 (Korean Standard), BS 6920:2000 (British Standard), SS245:1995 (Singapore Standard) FINETANK, the WRAS approved GRP SECTIONAL WATER TANK is being produced by the ISO-9001 certified Korean manufacturer. [ ADVANTAGES ] EXCELLENT HYGIENIC PROPERTISE * Nontoxic, WRAS certified materials * Suppression of algae and microorganisms with excellent blocking of sunlight * Minimization of moss and scale by smooth surface finish OUTSTANDING DURABILITY * Optimal system by FEM (Finite Element Method) design. * Anti-corrosion materials in SS316, HDG and PE coated S.S. ABSOLUTE WATER TIGHTNESS * Foam type gasket with excellent elasticity and resilience. FREE CAPACITY DESIGN * Various shapes to meet different site conditions (Square / Center vacant square / L-shape / Channel-shape, etc) * Versatile capacities (0.5m3 ~ 5,000m3). * Various panel sizes : 1x1, 0.5x0.5, 1x0.5, 0.3x0.3, 1x2, 1.15, etc. EASY INSTALLATION & MAINTENANCE * User-friendly installation even in the restricted area by using standardized panels and reinforcements. PRE-INSULATED PANELS (optional) * PU foam pre-insulated panels to avoid high heat or cold. MUTI-COMPARTMENTS (optional) * A tank can be partitioned into multi-compartments for respective use when tank is under cleaning or maintenance. [ SPECIFICATIONS ] 1 Panel : Hot-press molded SMC panel 2 Insulation : Poly Urethane Foam 3 Inner tie-rod : Stainless steel 316 / 304 / Stainless steel with PE coating - optional (External reinforcement system ->No inner tie-rod system is available up tp 4mH) 4 Roof support : SMC pultrusion pipe 5 External reinforcement : Hot dip galvanized steel 6 Roof support : SMC pultrusion pipe 7 Inner bolts : Stainless steel 316 / 304 8 External bolts : HDG steel / Stainless steel / Rubber capped steel 10 External ladder : HDG steel There're more options you're looking for. For more details, please feel free to contact us !
FINETANK - GRP SECTIONAL WATER TANK - High quality WATER STORAGE TANKS made of GRP PANELS & STEEL REINFORCEMENTS are available in various capacities and different shapes for various applications (residential/commercial buildings, water treatment plant, fire fighting, irrigation, etc.) FINETANK, the fine tank from the ISO-9001 certified Korean manufcaturer complies to international standards WRAS, BS, KS, SS. [ ADVANTAGES ] EXCELLENT HYGIENIC PROPERTISE * Nontoxic, WRAS certified materials * Suppression of algae and microorganisms with excellent blocking of sunlight * Minimization of moss and scale by smooth surface finish OUTSTANDING DURABILITY * Optimal system by FEM (Finite Element Method) design. * Anti-corrosion materials in SS316, HDG and PE coated S.S. ABSOLUTE WATER TIGHTNESS * Foam type gasket with excellent elasticity and resilience. FREE CAPACITY DESIGN * Various shapes to meet different site conditions (Square / Center vacant square / L-shape / Channel-shape, etc) * Versatile capacities (0.5m3 ~ 5,000m3). * Various panel sizes : 1x1, 0.5x0.5, 1x0.5, 0.3x0.3, 1x2, 1.15, etc. EASY INSTALLATION & MAINTENANCE * User-friendly installation even in the restricted area by using standardized panels and reinforcements. PRE-INSULATED PANELS (optional) * PU foam pre-insulated panels to avoid high heat or cold. MULTI-COMPARTMENTS (optional) * A tank can be partitioned into multi-compartments for respective use when tank is under cleaning or maintenance. [ SPECIFICATIONS ] 1 Panel : Hot-press molded SMC panel 2 Insulation : Poly Urethane Foam 3 Inner tie-rod : Stainless steel 316 / 304 / Stainless steel with PE coating - optional (External reinforcement system ->No inner tie-rod system is available up tp 4mH) 4 Roof support : SMC pultrusion pipe 5 External reinforcement : Hot dip galvanized steel 6 Roof support : SMC pultrusion pipe 7 Inner bolts : Stainless steel 316 / 304 8 External bolts : HDG steel / Stainless steel / Rubber capped steel 10 External ladder : HDG steel * INternational Certificats : WRAS, PSB, ISO-9001 There're more options you're looking for. For more details, please feel free to contact us !
Single-layer Stainless Steel Tank, Top Open Water Storage Tank, Fixed Single Layer Stainless Steel Container single-layer stainless steel container top open water storage tankWidely use in foods,dairy products, fruit juice beverages, chemical process, etc. It can be made according to special requirement of customers (double -layer storage tank, movable storage tank, fixed storage tank, pressure storage tank, jacket tank, ferment growing tank, fermentation tank, double-layer side blending tank, horizontal storage tank, square storage tank and so on). Olive oil tank adopt humanized structure design and easy operate, large water tank. 1. Anti-corrosive : our storage tank can stand corrosion of residual chlorine in air and water, we inspect tanks before delivery to ensure top quality. 2. Fine sealed: The compact design and fine sealed will avoid dirty goods in air comes in, thus to ensure liquid in storage tank clean. 3. Scientific water flow design : Sediment in the storage tank will not turn up owing to storage tank special design. 4. No need to water frequently: Wash the storage tank at regular intervals( generally 3 years one time). open sewage valve. The storage tank can be add a jacket for cooling or heating . Storage tanks also can for electric heating or steam heating. Storage tanks and other accessory vessels are used for storing of solvents, chemicals & any type of liquids. caustic soda storage tank, open top stainless steel tank, steel storage containers Stainless steel storage  tank Material: SS304 or SS316L or Duplex stainless or 904L Design Pressure: -1 -10 Bar (g) or ATM B9 Work Temperature: 0-200 °C Volumes: 100~30000L Construction : Vertical type or Horizontal type Jacket type  : Dimple jacket, full jacket, or coil jacket Structure  : Single layer vessel, vessel with jacket, vessel with jacket and insulation Heating or cooling function According to the heating or cooling requirement ,the tank will have jacket for requried function Opitional Motor: ABB, Siemens, SEW or Chinese brand Surface Finish: Mirror Polish or Matt polish or Acid wash&pickling or 2B Standard components : Manhole,sight glass , cleaning ball
Steel Water Tank hot dip galvanized water tank steel tower custom Tower Tank company Overhead Tower Tank Specification H section steel column, beam, and angle steel support Access ladder with safety cage Option of having a walkway around the tank Design certificate from registered professional engineer Surface finish: galvanized or painted The tower height can be 3m, 6m, 10m, 12m, 15m etc. At present, we have made the highest tower 28m. All the steel parts are prefabricated in factory, just assemble together with bolts&nuts. Installation service are available. Steel Water Tank Specification Water tank material Hot dip galvanized steel Water tank capacity 1m³~5000 m³ Water tank size According to the water volume or customer's request Using life â?¥20 years Galvanized panel Panel material mild carbon steel Q235 A Panel size 1220mm*1220mm,1000mm*1000mm Panel thickness 5mm, 4.5mm, 3mm, 2.5mm, 2mm, 1.5mm (It is different according to the tank dimension) Acceessories Bolt. nut & washers hot-dipped galvanized material Sealing material Non-toxic P.V.C foam tape shall be used in between the joints Covers from 1.4mm to 3.0mm of thickness hot-dipped galvanized material Ladders and Level Indicator hot-dipped galvanized material As a professional container house and steel structure chicken house manufacturer in China, our company and products are well received and got high reputation at home and abroad. For more product information, please click here. https://www.steelbuildingtech.com/
Product Name: Pressure round tank manway with sight glass for sale Valve Body Material: 1.4404/1.4301, SS304/SS316L(Forged) Seal Material: EPDM (standard) conforms to FDA177.2600 Surface Finishing: RA 0.5 to 0.8 um Pressure: 5.0 Bar Max. Working Tem.: 120 degree C Availably Size: 200, 220, 300, 350, 400, 430, 450, 500, 600 Gasket: EPDM, silicone or Viton Height: 100,120,150 Certificate: PED 2014/68/EU, FDA.177.2600
Product Name: Pressure round tank manway with sight glass for sale Valve Body Material: 1.4404/1.4301, SS304/SS316L(Forged) Seal Material: EPDM (standard) conforms to FDA177.2600 Surface Finishing: RA 0.5 to 0.8 um Pressure: 5.0 Bar Max. Working Tem.: 120 degree C Availably Size: 200, 220, 300, 350, 400, 430, 450, 500, 600 Gasket: EPDM, silicone or Viton Height: 100,120,150 Certificate: PED 2014/68/EU, FDA.177.2600
Supplier: Storage, Furniture And Decor
Buyer: Rattan Baskets Or Hampers.
