Single-Layer Corrugated Pipes

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Incoloy Alloy 908 is a high-temperature, high-strength, and highly corrosion-resistant alloy composed of elements such as nickel, chromium, molybdenum, and iron. It is a single-phase austenitic alloy, typically formed by casting and forging. Chemical composition: The chemical composition of Incoloy Alloy 908 is composed of elements such as nickel, chromium, iron, molybdenum, vanadium, manganese, tantalum, silicon, carbon, phosphorus, and sulfur. Nickel content is 40-45%, chromium content is 20-23%, iron content is 16-19%, and molybdenum content is 8-10%. Mechanical properties: Incoloy Alloy 908 has excellent high-temperature and high-strength performance. Its tensile strength is 135 ksi (930 MPa) (minimum), yield strength is 70 ksi (480 MPa) (minimum), and elongation is 25% (minimum). Physical properties: The density of Incoloy Alloy 908 is 8.14 g/cm�³, the melting point is 1338�°C (2440�°F), the thermal conductivity is 11.7 W/m�·K (100�°C), and the coefficient of thermal expansion is 13.7 �¼m/m-K (20-100�°C). Corrosion resistance: Incoloy Alloy 908 has excellent corrosion resistance, especially in high-temperature, high-pressure, and highly corrosive environments. It can withstand the corrosion of corrosive media such as sulfuric acid, hydrochloric acid, nitric acid, and fluoride, and can resist chloride stress corrosion cracking (SCC). The international standard designations for Incoloy alloy 908 include UNS N09908 and W.Nr. 1.4876. There are also corresponding standards and specifications in different countries and regions, such as AMS and ASTM standards in the United States, EN standards in Europe, and JIS and JPI standards in Japan. Here are the specific standards and designations for Incoloy alloy 908 in different countries: United States: AMS 5545, AMS 5546, AMS 5547, AMS 5549, ASTM B408, UNS N09908 Germany: DIN 17752, DIN 17753, DIN 17754, W.Nr. 1.4876 United Kingdom: BS HR 6 Europe: EN 10095 Japan: JIS H4551, JPI-SB46 We can provide the following the form:Incoloy alloy908 coil; Incoloy alloy908 strip;Incoloy alloy908 plate; Incoloy alloy908 sheets; Incoloy alloy908 tube; Incoloy alloy908 pipe;Incoloy alloy908 flat; Incoloy alloy908 bar GB:HR 6/JIS:H4551/UNS:N09908/W.Nr:1.4876

A swage nipple concentric is a type of pipe fitting that is used to connect two pipes of the same diameter. It is made of a single piece of metal that is swaged, or expanded, to fit tightly around the pipes. The swage nipple is then inserted into the pipes and secured with a nut. The technical specifications of a swage nipple concentric vary depending on the size and material of the fitting. However, some common specifications include: 1. Material: Carbon steel, Alloy steel, Stainless steel or Ductile 2. Size: 1/4 inch to 8 inches 3. Schedule: STD, XS, 160, XXS 4. Thread type: NPT, BSP, BSPT 5. Pressure rating: 100 psi to 20,000 psi Swage nipples concentric are commonly used in a variety of applications, including: A. Plumbing B. HVAC C. Fire sprinkler systems D. Pressure vessels E. Industrial piping They are a versatile and reliable type of pipe fitting that can be used in a wide range of conditions. Here are some additional features and benefits of swage nipple concentrics: a. They are easy to install and remove. b. They provide a secure and leak-free connection. c. They are resistant to corrosion and rust. d. They are available in a variety of sizes and materials to meet the needs of different applications.