Dc input poe
Pt-pse105g-e indoor single-port poe mid-span
Standard
1. Indoor using, 48vdc / 650ma, poe port 6kv (10 / 700us) surge-protection
2 Boost design, input voltage: 10-24vdc
3. Wide-temperature design: -40? - +65?
4. Rail slot on the back, can be fixed at guide rail
1. Boost poe injector
Pt-pse105g-e connected with switch to exchange data, supply power through cat5e cable to remote pd, effective distance is 100m.
2. Intelligence chip is inside, detective pd before supply power.
Pt-pse105g-e with intelligence chip inside, detective pd before supply power, if the pd is compliant with ieee802.3af / ieee802.3at standard, supply 48vdc power, if not do not supply power, avoid of device destroy and increase safety level .
3. External solar power supply system connected
Product allows 10-24vdc input and solar power panel is acceptable, output power is 30w, output current is 650ma, could powered for high power request pd, such as outdoor wireless base station, wireless ap, network cameras.
4. Better ambient temperature adaptation, convenience to fix.
Pt-pse105g-e's ambient temperature is good, -40? ~ +65 ?; with rail slot, can be fixed at guide rail.
Description: , dc 36v~72v input, 35w/56v ouput, 802.3at Application: industrial pc , Transportation , Security cam Any gigabit ethernet terminals which work with industrial dc input system Any gigabit ethernet terminals which require power under 30w Plastic case material: pc Plastic case finish: texture Plastic case color: gray Plastic case dimension: 125 x 75 x 38 (l x w x h) mm Numbers of unit in one carton: 50pcs Carton weight: n.W.15kgs/g.W.16kgs Carton dimension: 1.3 cuft. White box dimension: 165 x 82.5 x 44 (l x w x h) mm
Qx80h is q series DC high-speed input module, negative common terminal type, 16 points. Qx80h price (face price), the market stock is very small. Qx80h Parameter Description: 24VDC / 4mA, common cathode, 16 points, terminal block (high speed). Specification details of PLC module qx80h: DC input module negative common end input points 16 points isolation method Optocoupler rated input voltage DC24V 20% - 15%, ripple coefficient above 5%) rated input current about 6mA derating chart on voltage / on current 13V or higher / 3mA or higher off voltage / off current 8V or less / 1.6mA or less function setting SW2 off interrupt, on high speed input dielectric withstand voltage 560vac MS / 3 cycles (altitude 2000m (6557.38 feet)) [insulation resistance] 10m or higher measured by insulation resistance tester through 1500vp-p noise voltage, 1 Voice simulator with s voice width and 25 to 60Hz voice frequency First instantaneous voice iec61000-4-4: 1kV protection grade IP2X common terminal arrangement 8 points / common terminal common terminal: tb9, tb18 I / O points 16 I / O allocation is set to 16 point high-speed input module or interrupt module working status indicator set by setting in GX developer switch running indicator on indication (LED) external connection 18 point terminal block (M3 6 screw) applicable wire diameter core 0.3mm2 to 0.75mm2 (maximum outer diameter 2.8mm) applicable to clamping terminal R1 25 ~ 3 clamping terminal with sleeve cannot be used 5VDC internal current consumption 80mA standard: all points on overall dimension h w d 98 * 27.4 * 90 mm weight 0.16kg
AC to DC converter battery charger 150-1000VDC rectifier 120KW power supply Product Introductionï¼? SANDI AC/DC Charger is specially developed for DC chargers. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase, DC output voltage range from 150 to 1000VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger. Unique function High efficiency over the full load range, full load efficiency greater than 95% Wide output voltage range, 150-1000VDC, suitable for a wide range of Lithium or lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main featuresï¼? Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Wide input voltage range: 260~ 530Vac, adaptable to various power grid environments Three-phase AC input without neutral wire: Simplifies system design, eliminates the risk of excessive neutral current, and reduces system costs. Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Battery anti backflow: effectively protects the battery while ensuring reliable and safe operation of the system Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. RS485 interface (Optional)
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Remote Control DC Input Motion Sensor Motion Sensor Module DC Input 5V/12V DC Input Microwave Motion Sensor Remote Controllable Version HNS112 5.8GHz C-band microwave, tri-level dimming control. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. Features 5.8GHz C-band microwave, tri-level dimming control. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 0~10V DC output signal. Super compact, flexible to be integrated into any suitable fixtures. Dual-PD technology, real Daylight monitoring function for built-in application. IR remote commissioning, easy setting and user friendly. Detection range up to 12m in diameter. Mounting height: 3~6m. Operation temperature: -20�C~ +70�C. RoHS compliant. Settings(Remote control IR12) Permanent ON/OFF function Press ON/OFF button, fixture goes to permanent on or permanent off mode, sensor is disabled. *press "Auto" ,"Reset" or "Ambient learn" to quit this mode. Dim +/- Press "Dim" button to automatically dim up or down the light brightness during hold-time from 10% to 100%. Another press to lock it down when desired brightness is achieved. *after desired brightness is locked down, if user wants to dim again reversely, just press the Dim?? button again and then lock down the new brightness again. Sensor mode Press "Auto" button, the sensor starts to work and all settings remain the same as the latest status before the light was switched on/off. Reset function Press "Reset" button, all settings go back to factory default settings. Factory default settings Sensitivity=100% Daylight sensor=disable Hold time=90s Twilight time=5min Twilight level=10% Ambient learn Press "Ambient learn" button, the latest surrounding lux value overwrites previous lux value learned, and set as the daylight threshold. This feature enables the fixture to function well in any real application circumstance. Test mode "Test mode" is for testing purpose only, for users to check the functionality and choose the desired detection range. The sensor goes to test mode automatically after pressing this button. Users can quit this mode by pressing "ON/OFF", "Reset' or any button of "Hold time". The sensor settings are changed accordingly. *Test mode defaulted settings Daylight sensor=disable Hold time=3s Twilight time=N/A Twilight level=N/A In this mode, when used for on/off control, after motion detected, sensor enters into a cycle of 3s on and 2s off. In this mode, when used for tri-level dimming control, after motion detected, sensor enters into a cycle of 3s on and 2s off(0.5s soft off + 1.5s off). -
5V/12V DC Input Microwave Motion Sensor Highbay Version DC Input Motion Sensor Module Highbay DC Input Motion Sensor HNS111HB 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. Features 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 0~10V DC output signal Super compact, flexible to be integrated into any suitable fixtures. Dual ï¹£ PD technology, real Daylight monitoring function for built-in application. IR remote commissioning, easy setting and user friendly. Detection range up to 18m in diameter. Mounting height: 10~12m. Operation temperature: -20 ~ +70 RoHS compliant. Settings(Remote control IR12) Permanent ON/OFF function Press ON/OFF button, fixture goes to permanent on or permanent off mode, sensor is disabled. *press "Auto" ,"Reset" or "Ambient learn" to quit this mode. Dim +/- Press "Dim" button to automatically dim up or down the light brightness during hold-time from 10% to 100%. Another press to lock it down when desired brightness is achieved. *after desired brightness is locked down, if user wants to dim again reversely, just press the Dim button again and then lock down the new brightness again. Sensor mode Press "Auto" button, the sensor starts to work and all settings remain the same as the latest status before the light was switched on/off. Reset function Press "Reset" button, all settings go back to factory default settings. Factory default settings Sensitivity=100% Daylight sensor=disable Hold time=90s Twilight time=5min Twilight level=10% Ambient learn Press "Ambient learn" button, the latest surrounding lux value overwrites previous lux value learned, and set as the daylight threshold. This feature enables the fixture to function well in any real application circumstance. Test mode "Test mode" is for testing purpose only, for users to check the functionality and choose the desired detection range. The sensor goes to test mode automatically after pressing this button. Users can quit this mode by pressing "ON/OFF", "Reset' or any button of "Hold time". The sensor settings are changed accordingly. *Test mode defaulted settings Daylight sensor=disable Hold time=3s Twilight time=N/A Twilight level=N/A In this mode, when used for on/off control, after motion detected, sensor enters into a cycle of 3s on and 2s off. In this mode, when used for tri-level dimming control, after motion detected, sensor enters into a cycle of 3s on and 2s off(0.5s soft off + 1.5s off). -
DC Input Motion Sensor Module Standard Motion Sensor Module 5V/12V DC Input Microwave Motion Sensor - Standard Version HNS101D 5.8GHz C-band microwave, tri-level dimming function. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. Features 5.8GHz C-band microwave, tri-level dimming function. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 5V DC PWM output or 0~10V DC signal. Super compact, flexible to be integrated in t o any suitable fixtures. Dual-PD technology, real Daylight monitoring function for built-in application. 8 pin DIP switch setting, multiple options to meet different customer demands. Detection range up to 12m in diameter. Mounting height: 3~6m. Operation temperature; -20? ~ + 70?. RoHS compliant. Settings Detection range Detection range can be reduced by selecting the combination on the DIP switches to fit precisely each application. Hold-time Hold-time means the time period to keep the lamp on 100% after motion detected. *when hold-time set as 3s, sensor enters into test mode, this test mode is mainly for users to choose the desired detection range. In this mode, the daylight sensor is disabled, when there is no motion, fixture keeps off, when there is motion detected, fixture keeps a cycle of 3s on and 2s off. Daylight sensor Daylight sensor means the daylight threshold to enable or disable the sensor function. "Disable": The sensor works always, even during daylight. w50lux": The sensor works only in twilight. w10lux, 2luxw: The sensor works only in the dark. Stand-by period This is the time period that the lamp remains at a low light level before it is completely switched off in the long absence of people. ?+? means bi-level dimming control, the fixture never switch off. Stand-by dimming level This is the dimmed low light level you would like to have after the hold-time in the absence of people. Daylight monitoring function Utilizing the Dual-PD technology, this sensor can tell the difference of natural light and artificial light(lamp) from behind the diffuser, switch on automatically(even without movements) when the ambient light is below target value, and then switch off automatically whenever the artificial light is not required(ambient light is bright enough). This is the REAL & INTELLIGENT daylight monitoring sensor for built-in installation. Note: Lux-Off sampling time?30s; Lux-On sampling time?10s. Lux-On function takes effect only when standby dimming period set at+?
5V/12V DC Input Microwave Motion Sensor - Standard Version DC Input Motion Sensor Module Adjustable Motion Sensor Module HNS101 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 5V DC high-low voltage output signal. Features 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:�?�25mA. 5V DC high-low voltage output signal. Super compact, flexible to be integrated into any suitable fixtures. Dual-PD technology, real Lux-Off function for built-in application. 8 pin DIP switch setting, multiple options to meet different customer demands. Detection range up to 12m in diameter. Mounting height: 3~6m. Operation temperature: -20�?? ~ +70�??. RoHS compliant. Settings Detection range Detection range can be reduced by selecting the combination on the DIP switches to fit precisely each application. Hold-time Hold-time means the time period to keep the lamp on 100% after motion detected. *when hold-time set as 3s, sensor enters into test mode, this test mode is mainly for users to choose the desired detection range. In this mode, the daylight sensor is disabled, when there is no motion, fixture keeps off, when there is motion detected, fixture keeps a cycle of 3s on and 2s off. Daylight sensor Daylight sensor means the daylight threshold to enable or disable the sensor function. "Disable":The sensor works always, even during daylight. w50lux, 25lux": The sensor works only in twilight. "10lux, 2lux": The sensor works only in the dark. -
5V/12V DC Input Microwave Motion Sensor Remote Controllable Version Remote Control DC Input Motion Sensor Motion Sensor Module DC Input HNS111 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. Features 5.8GHz C-band microwave. Input voltage 12V DC (5V & 24V DC version available on request). Input current:25mA. 5V DC high-low voltage & PWM output signal(0~10v version available on request) Super compact, flexible to be integrated into any suitable fixtures. Dual - PD technology, real Lux -Off & Daylight monitoring function for built-in application. IR remote commissioning, easy setting and user friendly. Detection range up to 12m in diameter. Mounting height: 3~6m. Operation temperature: -20 ~ +70 RoHS compliant. Settings(Remote control IR12) Permanent ON/OFF function Press ON/OFF button, fixture goes to permanent on or permanent off mode, sensor is disabled. *press "Auto" ,"Reset" or "Ambient learn" to quit this mode. Dim +/- Press "Dim" button to automatically dim up or down the light brightness during hold-time from 10% to 100%. Another press to lock it down when desired brightness is achieved. *after desired brightness is locked down, if user wants to dim again reversely, just press the Dim button again and then lock down the new brightness again. Sensor mode Press "Auto" button, the sensor starts to work and all settings remain the same as the latest status before the light was switched on/off. Reset function Press "Reset" button, all settings go back to factory default settings. Factory default settings Sensitivity=100% Daylight sensor=disable Hold time=90s Twilight time=5min Twilight level=10% Ambient learn Press "Ambient learn" button, the latest surrounding lux value overwrites previous lux value learned, and set as the daylight threshold. This feature enables the fixture to function well in any real application circumstance. Test mode "Test mode" is for testing purpose only, for users to check the functionality and choose the desired detection range. The sensor goes to test mode automatically after pressing this button. Users can quit this mode by pressing "ON/OFF", "Reset' or any button of "Hold time". The sensor settings are changed accordingly. *Test mode defaulted settings Daylight sensor=disable Hold time=3s Twilight time=N/A Twilight level=N/A In this mode, when used for on/off control, after motion detected, sensor enters into a cycle of 3s on and 2s off. In this mode, when used for tri-level dimming control, after motion detected, sensor enters into a cycle of 3s on and 2s off(0.5s soft off + 1.5s off). -
