Electric Railway Transfer Cart

The rail transfer cart is power by busbar(electric sliding line). It gets power from sliding during the cart running. The electric control system of the cart realize it start, stop, go forward and backward. Features of rail transfer cart: Simple structure, low cost; Has no strict on rail construction; Suitable to working area with short running distance; Suitable to working area with high using frequency; Has no limit on running distance; Can be applied in high-temperature environment; Box girder structure; Reasonable design, reliable operation. Can be add hydraulic lifting device; Can be add dumping device; High efficiency, low energy consumption, The whole rail transfer cart is packed by high quality plastic cloth

Product Introduction - Electric Operated Transfer Carriage The electric operated transfer carriage is an electric material transfer carriage powered by cable reels, it is designed for material handling. The electric operated transfer carriages get power from AC 380V through device of cable drum installed at bottom. Motor is controlled by power through AC control system, use this principle to operateelectric operated transfer carriages to start, stop, go forward, backward and so on. Features - Electric Operated Transfer Carriage Metallurgical Motor - Y series metallurgical motor is suitable for frequent starting. Cable reel - With a large adjustment range for take - up torque, constant tension after adjustment and stability, good synchronization performance. Self-locking ability, no cable slipping - Reasonable structure arrangement, easy installation, use, maintenance, stable and reliable performance. Workshop bay to bay commonly used carriages - This series of electric operated transfer carriages are mainly used in high temperature, harsh, explosion-proof occasions, it usually used in workshop bay to bay transfer. Large load capacity - The using time is unlimit, adapted to any load, high frequency of use. Custom Options - Electric Operated Transfer Carriage Flat decks or fixtures customized for specific loads. Custom deck configurations including built-in scales and lift/tilt/rotate capabilities. Non-guided steering. Alternative drive and steering systems including gear reducer axle drives and individually-controlled drive wheels. Fixed or variable speeds with forward/reverse function. Drives with acceleration/deceleration capabilities. Variety of operator control systems including fixed user interface, pendant control on coil cord, and radio-controlled remote operation. Safety features including horns, flashing lights, e-stops, bumpers and collision avoidance systems. Application - Electric Operated Transfer Carriage The electric operated transfer carriages have a widely application fields including Automotive, steel, heavy industry, engineering, aerospace, coal, nuclear energy, water wheel manufacturing, paper industry, ceramics workshop, metallurgy heavy industry, slab transfer workshop, Coal Electrical and Mechanical Industry, unfired brick transshipment industry, etc.

Product Introduction for electric transfer cart This kind of electric transfer cart is powered by mobile cable and composed by cart frame, the electric motor, gear reducer, wheel, electrical appliance box, mobile cable, Shaft and connecting shaft, handle box, alarm light, buffer device, pendant control or wireless remote control and some other accessories and so on. Application of electric transfer cart Electric transfer cart is suitable for various industries, steel mill, transfer steel products such as steel structure, steel pipe, steel billets, steel ladle and coil, etc Paper roll plant: transfer paper coil Painting shops: transfer workpiece into the painting room Sand blasting room, other industries: shipbuilding, quarries, warehouses and multi-bay workshops, etc. Characters of electric transfer cart · Anti-explosion · Anti-high temperature · Apply to various occasions · Stable start, big starting power, small impact to the gear reducer, low voltage, long lifetime and so on. · It has no strict requirement for the construction of the railway, · No limit of running hours, · Safe and convenient operation for there is no wire outside the cart, · Adjustable speed.

Product Description About the electric transfer rail cart, the AC 380V cable relies on the retractable cable of the reeling device to realize supply electricity for electric transfer rail cart. The reeling device is placed under the electric transfer rail cart, and the power is directly controlled by the AC control system to start, stop and so on. The operating system is a low-voltage 36V power supply control. To avoid damage to the cable, add a cable reel as a retracting/discharging device. Due to the limitation of the cable, it is suitable for a short-distance rail transportation system, but its structure is simple and the price is low. Features Metallurgical Motor - Y series metallurgical motor is suitable for frequent starting. Cable reel - With a large adjustment range for take-up torque, constant tension after adjustment and stability, good synchronization performance. Self-locking ability, no cable slipping - Reasonable structure arrangement, easy installation, use, maintenance, stable and reliable performance. Application The electric transfer rail carts are widely applied in many fields, such as automotive, steel, heavy industry, engineering, aerospace, coal, nuclear energy, water wheel manufacturing, paper industry, ceramics workshop, metallurgy heavy industry, slab transfer workshop, coal electrical and mechanical industry, unfired brick transshipment industry, etc. Company Information Xinxiang New Leader Machinery Manufacturing Co., Ltd is devoted to manufacture and sell lifting and handling equipment. We can produce 1-500 ton range of various tonnage of KPD rail low voltage series, KPJ cable reel series, KPC safety sliding line series, KPX battery powered series, BWP rubber wheel transfer cart series, KPT towed cable series, KP non-power type seven series which including turning electric flat car, trackless electric flat car, ladle car, ferry electric flat car, hydraulic lifting electric transfer car, electric winch, rail wheel and so on more than 90 products.

Products Introduce The electric material transfer cart is powered by storage battery. The storage battery is installed in the electric material transfer cart. The storage batteries supplied the electricity to the DC motor through the electrical control system. Use this principle to operate the electric material transfer cart to starting, stopping, going forward, going backward, adjusting the speed and so on. Features Of Electric Material Transfer Cart 1. Battery power supply, operating distance is not restricted. 2. Can directly running on the concrete. 3. Turn to at will. 4. Change direction and route at any time. 5. Full load uninterrupted for 4-5 hours.

Product Description About the electric mold transfer cart, literally speak, it is an electric transfer cart designed for mold transfer, which is the special type compared with traditional transfer cart. The electric mold transfer cart is powered by busbar, its conducts AC380v busbar line directly into the AC electrical control systom of the electric mold transfer cart to let it start, stop, go forward backforward and so on. The electric mold transfer cart gets power from the slider of the safe busbar which is moved by the carts running. The operation system is low voltage 36V power. Products Details Frame The frame is two longitudinal beam, several beams with steel panel welded together, which adopts box beam structure according to the crane principle and combined with the design of the electric mold transfer cart. Its main feather: large load bearing, little table deformation, long service lifetime. Cast Steel Wheel The wheel, its material is ZG55, Change conveniently, install easily, the larger capacity cargoes can be transported, up to now, the largest capacity has been reach to 500 tons we have done among electric mold transfer cart. Three-in-one type Reducer, Motor and Brake This type gear box with advantage of high efficiency, operate steadily, easy installation and maintenance, etc; Brake is composed by brake frame, brake parts, brake operating device and so on, it is a safety device to ensure vehicle working safely; The electric motor is AC Motor. Busbar The electric mold transfer cart is powered by this busbar as the picturing showing. However, The busbar is limited by the position, it can be installed between the two rails, the hole should be digged or it can also be placed in the channel outside the track. All are customized as per your true demand. Advantages Compared with other electric mold transfer cart, the electric mold transfer cart powered by busbar is with low cost and high frequency; The electric mold transfer cart can be applied in many occasions, such as bad environment, high temperature, ferry...; AC motor, simple structure, not limited for the using time; This kinds of electric mold transfer cart is powered by busbar, so there is not strict requirement for the construction of the railway; Professional team from Xinxiang New Leader Machinery Manufacturing Co., Ltd. the proper solution can be provided once getting for your inquiry.

Product Description About the foundry plant railroad electric transfer cart, literally speak, it is an electric transfer cart running on rail and designed heavy material or equipment handling. Due to its low price and high efficiency has been new favorite in the industry transport field all over the world with hot market. The power supply of the foundry plant railroad electric transfer cart can be choosed according different application, such as battery powered, low voltage railway powered, cable reel powered, towed cable powered, busbar powered and so on. Features Specially designed box beam structure; Running distance has no limit; Speed adjustment 0-30m/min; Short braking distance; Finding application in industrial units for diverting/merging unit loads between multiple lanes; Used in areas like layer pick operations, workstations, transferring loads from multiple palletizer and others; Available in options of single deck or double deck versions; Coming with suitable lift support for addressing multiple receiving and delivery levels; Requires less maintenance; All of the foundry plant railroad electric transfer cart can be customized as per demands.

*The depth of the feed, the real-time battery power digital display, the operator is clear at a glance *Dual control system, both electronic feed and mechanical operation feed *Electronic feed, the feed precision is adjustable, realize the dual purpose of primary grinding and precise grinding *Preset the warning feed depth for grinding to prevent excessive grinding and cause grinding accidents *Super endurance capability, can work continuously for 1 hour *The whole machine is waterproof and can be used below minus 30 Specification Model LJ-LGF2001 Type Electric Rail Grinding Machine Material Aluminium Operating speed 4500r/min Rated power 5Kw (brushless DC motor) Grinding wheel feed accuracy 0.1 mm Grinding wheel size 150*55*75x4-M8 mm (outer diameter inner diameter thickness) Maximum tilt range of the grinding wheel 90 ° in one direction Operating temperature requirements -30 to 45 Grinding wheel type resin thick-walled cup-shaped grinding wheel Battery pack capacity 21Ah Rated voltage of battery pack 72V Weight 70Kg Profiling function realize profiling grinding of the outer edge contour of different types of rails Endurance capability(one charge) thermit welding grind around 8 welds; laser welding grind around 10 welds Grinding wheel feeding mode Dual control system, which can feed both mechanically and electronically Electronic feed It is divided into three gears for key switching and operation. First gear: fine grinding, unit feed 0.1mm Second gear: initial grinding, unit feed 0.3m Third gear: initial grinding, unit feed 0.5mm

Supplier: Solid state relays (electronic relays), heat sinks and din rail mounting clamps