Key Features
1.It has a high thermal conductivity
2.Excellent comprehensive properties, elasticity, non-yellowing, no bleed oil
3.Moisture, dirt and other atmospheric composition proof
4.Relieving the mechanical stress and tension that cased by machinery, heat shock and vibrate
5.Good corona resistance and electrical insulation performance
6.Excellent outdoor aging-resistance for 20-30 years
7.Stable mechanical and electrical properties between -60- C
Typical Applications
Used for sealing LED lamps, thermal dissipation of auto electrical components, PCB and other heat dissipation components. Gap filling between power transistor, diode thyristor and substrates.
Technical Data Table
PROPERTY STANDARD/UNITS VALUE
Before curing SI1316 SI1317
Color Visual inspection White
Viscosity 25 227;C, mPa 8226;s Paste
Density 25 227;C, g/cm3 1.65 2.25
Tack free time 25 227;C, 55%RH, min 2~5 2~5
After cured
Hardness Shore A 50 1615
Thermal conductivity W/m.K 0.82 1.50
Elongation at break % 150 100
Tensile strength MPa Y1
90 Y2
Shear strength MPa, iron/iron Y1 Y2
Dielectric strength kV/mm, 25 227;C 20 20
Loss factor 1 MHz, 25 227;C 0.09 0.09
Dielectric constant 1 MHz, 25227;C 2.9 2.9
Volume resistance (DC500V) | 8226; cm 2.01014
2.0 1014
SI1316. 310ml/tube, 25 tubes/carton; 100ml/tube, 100 tubes/carton.
SI1317. 310ml/tube, 25 tubes/carton
High-temperature resistance, anti-aging, high thermal conductivity, and low overflow rate
Supplier: Release liner, self adhesive label stock, self adhesive paper, self adhesive films , floor marking tapes, masking tape, kraft paper tape, thermal paper, thermal rolls, multi coloured self adhesive labels, holograms , thermal transfer ribbons, thermal transfer wax ribbons, thermal transfer wax resin ribbons, thermal transfer resin ribbon, vinyl tapes, barcode labels , multi coloured printed kraft paper tape, printed labels, printer ribbons, multi coloured labels, printed tape, hologram labels
DB118 This product is a one-component epoxy resin adhesive with high thermal conductivity, which is the best matching adhesive for thermal bonding of chips. Applicable to all kinds of electronic products, characterized by rapid thermal curing, and easy to apply. Upon cure, it has high bonding strength, good thermal conductivity, low shrinkage, low moisture absorption, good insulation performance, etc., which can reduce the working temperature of the chip, extend the life of the chip
LC1001 is the semi-flowing heat-resistant silicone adhesive sealant which is made of special silicone rubber material the addition of thermal powders. With excellent conductivity,V0 flame retardant grade, excellent temperature resistance, can be in the range of 60 ~ 280 Long-term use. As well as good adhesion, long term use will not fall off, will not produce Contact gap to reduce thermal conductivity, moisture-proof, anti-seismic, anti-corona, anti-leakage and aging .The properties are widely used for the adhesion and sealing of the electronic components with high thermal conductivity, which is a single part of the acetone oxime type, It can be cured silicone rubber and conforms to the requirements of ROHS REACH UL. Typical Applications High power LED lamps and lanterns, electrical power, microwave oven, electronic components and other industrial products of thermal conductive adhesive sealing, alternative thermal conductive silicone used in high-power electric module and radiator thermal conductivity between fixed filling adhesive, no card buckle screw, more reliable filling heat, simple process and lower cost. Applying Process 1.Surface clean : Clean the surface of the adhesive object and remove the rust, dust and oil. 2.Sizing: Twist the cap of the hose, squeeze the gel into the clean surface, and make it natural. 3.Curing: Place the bonded or sealed parts in the air while them to solidify naturally. Curing is a process from surface to the internal, within 24 hours (at room temperature and 55% relative humidity) will cure the depth of the 2 ~ 4 mm, if the site location is deeper that completely curing time will be postpone, especially it is not easy to come into contact with air. if the temperature is low, cure time also will be postpone .Prior to further processing or wrapping the bonded parts, it is recommended that the user wait long enough to ensure that the adhesion and integrity of the adhesion are not affected. For more , please kindly feel free to contact
Dry Lamination Adhesives Our Dry Lamination Adhesive is Acrylic Copolymer based adhesive, suitable for lamination of films (clear BOPP & PET, PVC, MET_PET, MET BOPP, & MAT BOPP etc.) to printed paper / duplex board using Dry Lamination Process on Bilhofer, Paper Plast, Wenchuan, Yii Lee type of automatic dry lamination machines. Advantages : 1. Suitable for dark prints, Matt Films, No tarnishing on gold prints. 2. Better performance with respect to creasing, embossing, guttering, in carton manufacturing, & book binding. 3. It is Odorless. 4. Printed shades are not affected by the use of this adhesive. 5. Application system can be cleaned by use of normal water. 6. No wrinkles on ageing upto 80 degree C for 2 hours with film PET. 7. High degree of non-foaming characteristics. 8. Online slitting can be conducted in the application of film to printed paper/board using dry lamination process.
1.color white,grey 2.thermal conductivity:1 8 w/m.k 3.working temp:-40 220 4.shelf life:12 M
Supplier: Sealants,adhesives and glue
Services: Shipping
Buyer: Chemicals
Supplier: Industrial adhesives like cyanoacrylates, anaerobic adhesives, silicone sealants, modified silanes , epoxies, polysulphides, brake shoes bonding epoxies, acrylic adhesives and so on...
Services:
SECrosslink-8801 UV cured conductive adhesive, low temperature resistance, aging resistance, flexibility, low Tg. Brand SECrosslink Type SECrosslink-8801 Curing method UV energy Resin acrylate Silver content 78% Viscosity 40000cPs UV wavelength 365 nm Irradiation time 10 s Shearing strength 8 MPa Volume resistivity
