Building facades or large steel forms used in plant construction consists of a set including the moon scaffolding, used as a building exterior and core gaengpom
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
* Stainless steel I-beam is a long steel bar with a grooved section. It can be used to form various stress components according to the different needs of the structure, and can also be used as a connector between components. It is widely used in various building structures and engineering structures, such as house beams, bridges, transmission towers, hoisting and transportation machinery, ships, industrial furnaces, reaction towers, container racks and warehouse shelves. Stainless steel I-beam is a carbon structural steel used for construction. It is a simple section steel, mainly used for metal components and plant frames. Good weldability, plastic deformation performance and mechanical strength are required in use. The raw steel billet of stainless steel I-beam is low carbon square steel billet, and the finished stainless steel I-beam is delivered in hot rolling forming, normalizing or hot rolling state. Product Name : Stainless : Steel I beam Standard : DIN GB JIS BA AISI ASTM EN GOST etc. Size : As customer request Technique : Stainless steel Packing : By bundles with steel strips or as customer request Surface Treatment : Sandblasting, solution pickling Application : Mechanical & manufacture,Steel structure,Shipbuilding,Bridging,Automobile chassis, etc. Warehouse Storage * Shandong Jintuo Metal Materials Co., Ltd is located in Liaocheng City, the capital of steel tubes. It is a large enterprise specializing in the sales of carbon steel, stainless steel, galvanized color coated products, and copper and aluminum.Our company adopts a flexible business approach and management mechanism to provide good services to customers, while also considering the interests of the owner and the project, in order to ensure the quality of the project Packing and shipping * Our products are exported to multiple overseas countries and regions such as Europe, America, South Asia, Southeast Asia, Africa, and Latin America, and have won the trust and support of customers with excellent quality and service. During the supply process, the company can timely use sufficient funds to adjust the production variety and model of the steel plant, ensuring the use needs during the peak construction period.
Product:Structural's Brand:Renaissance Pipe Fitting Inc. Sizes:Refer the specification Condition:New Rating:4.5, based on 122 reviews price:Start from 30 USD Stainless Steel Structural's, Carbon Steel Structural's, Nickel Alloys Structural's, Monel 400 & 500, Inconel 600 & 625, Structuralsupplier. RFP India is India's well-known manufacturer, supplier and exporter of Structural steel, which is a steel construction material, and formed utilizing a precise shape or cross section along with certain standards of chemical composition and mechanical properties. Structural steel shape, size, composition, strength, storage, etc., is regulated in most industrialized countries. Structural steel members, such as I-beams, have high second moments of area, which allow them to be very stiff in respect to their cross-sectional area. Apart from I-beans, we also provide in different shapes such as Z-Shape, HSS-Shape, Angle (L-shaped cross-section), Structural channel or C-beam or C cross-section, Tee (T-shaped cross-section), and Rail profile (asymmetrical I-beam) among others.
Abstract of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine can bend the roll formed pipe, and let the drainpipe and the bending connect to be the whole.The product after roll forming has long working time than the tranditional ppc pipe, and not aging. It can make the project more integrate, and help to enhance the image of the all project. Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine is composed of uncoiler, the feed leading table, the main machine, the formation cutting device, hydraulic system, control system and the product bracket. Usageï¼?Our downspout roll forming machine mainly consists of uncoiler, roll forming system, cutting equipment, protective guard, hydraulic system, control system and out table. It can make curve for down pipe to meet the requirement of practical engineering projects. Machine components Passive uncoiler Guiding unit Roll forming machine Cutting unit Hydraulic station PLC control cabinet Supporter table Security cover Elbow machine Technical process Passive uncoil Feeding Roll formingCut to lengthOutput tableElbow with pipe Technical parameters ItemsSpecifications Material SpecGalvanized steel sheet, color sheet Thickness of Coil Sheet0.3 0.8mm Main Motor Power5.5kw Forming Speed10-15m/min Hydraulic Station Power3kw Quantity of Stands18 Hydraulic Pressure10~12Mpa Controlling SystemPanasonic PLC Index Error of Length10m±2mm Total Weight7T Voltage380V 3 phase 50Hz Features of this Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine lower cost high efficiency reliable working low energy consumption Components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine steel strip supporting frame Feeding platform Automatic shearing system Hydraulic system Steel strip unfolding system Computer control system (imported computer) High-precision automatic counter Receiving table Suitable process material: colored steel sheet, aluminium steel sheet, and galvanized steel shee Optional components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine Manual uncoiler frame in different tons Hydraulic automatic uncoiler Working space and workman for the equipment: 1. Ground-level land 2. 5T overhead travelling crane 3. Space for storing the material 4. Space for laying the machine 5. Road for vehicle moving 6. Workman: 2, operator and porter
Specifications for Keel Equipment Light gauge steel frame roll forming machine Manual Un-coiler: Max Capacity: 5000kgs Inner diameter of coil:400-600mm Manual with brake Leveling Device: Ensure the material level and straight The width can be adjusted Main Forming System: Width & Height & Thickness of sheet: According to Drawings Material: GI sheet coil or Colored sheet coil Motor Power: 5.5 kw forming system Roller material:Cr12 Surface of Roller: Heat treatment HRC 58-60 Diameter of main shaft: 60mm #45 steel, heat treat modulation Forming station: 12 stations. Transmission: by chain and gear Measuring accuracy: +/- 0.5 mm/M. Arch middle plate: 30mm thickness. Output: 8-10 Tons per shift (8 hrs.). The machine base is assembled and welded by high quality steel. Cutting way: Tracking Oil pump station: 1set Motor power of Oil pump station: 7.5kw with cooling system Forced air cooling device available. Cutting mould: 1 sets Material of blade: CR12 with heat treatment HRC60-62. Electrical System: Control system: HMI & PLC control panel Power: 380V 50Hz (as per local requirement) Run-out Table: Frame: A3 Roller type Quantity: 1 pc
Steel structure warehouse is more durable and can be coated with aluminum compounds to prevent rusting. They are also cheaper and much quicker to construct since all of the drilling, cutting, and welding is done before the components are sent to the construction site to be assembled. One of the final benefits of pre-engineered steel buildings is that the overlapping panels offer better insulation to keep the building warmer in the winter and cooler in the summer. Steel structure warehouse usually cost a little less than normal buildings. The construction process with pre-engineered steel buildings is usually not affected by delays like normal construction. Since the building just needs to be assembled, there are rarely any surprise cost increases. Also, these buildings can be assembled and erected by 5) easily installation , save manpower According to the clients
Abstract of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine : Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine can bend the roll formed pipe, and let the drainpipe and the bending connect to be the whole.The product after roll forming has long working time than the tranditional ppc pipe, and not aging. It can make the project more integrate, and help to enhance the image of the all project. Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine is composed of uncoiler, the feed leading table, the main machine, the formation cutting device, hydraulic system, control system and the product bracket. UsageOur downspout roll forming machine mainly consists of uncoiler, roll forming system, cutting equipment, protective guard, hydraulic system, control system and out table. It can make curve for down pipe to meet the requirement of practical engineering projects. Machine components Passive uncoiler Guiding unit Roll forming machine Cutting unit Hydraulic station PLC control cabinet Supporter table Security cover Elbow machine Technical process Passive uncoil FeedingRoll formingCut to length?Output table?Elbow with pipe Technical parameters ItemsSpecifications Material SpecGalvanized steel sheet, color sheet Thickness of Coil Sheet0.3 ?0.8mm Main Motor Power5.5kw Forming Speed10-15m/min Hydraulic Station Power3kw Quantity of Stands18 Hydraulic Pressure10~12Mpa Controlling SystemPanasonic PLC Index Error of Length10m±2mm Total Weight7T Voltage380V 3 phase 50Hz Features of this Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine lower cost high efficiency reliable working low energy consumption Components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine steel strip supporting frame Feeding platform Automatic shearing system Hydraulic system Steel strip unfolding system Computer control system (imported computer) High-precision automatic counter Receiving table Suitable process material: colored steel sheet, aluminium steel sheet, and galvanized steel shee Optional components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine Manual uncoiler frame in different tons Hydraulic automatic uncoiler Working space and workman for the equipment: 1. Ground-level land 2. 5T overhead travelling crane 3. Space for storing the material 4. Space for laying the machine 5. Road for vehicle moving 6. Workman: 2, operator and porter
Abstract of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine : Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine can bend the roll formed pipe, and let the drainpipe and the bending connect to be the whole.The product after roll forming has long working time than the tranditional ppc pipe, and not aging. It can make the project more integrate, and help to enhance the image of the all project. Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine is composed of uncoiler, the feed leading table, the main machine, the formation cutting device, hydraulic system, control system and the product bracket. Usage Our downspout roll forming machine mainly consists of uncoiler, roll forming system, cutting equipment, protective guard, hydraulic system, control system and out table. It can make curve for down pipe to meet the requirement of practical engineering projects. Machine components Passive uncoiler Guiding unit Roll forming machine Cutting unit Hydraulic station PLC control cabinet Supporter table Security cover Elbow machine Technical process Passive uncoil Feeding Roll forming Cut to length Output table Elbow with pipe Technical parameters ItemsSpecifications Material SpecGalvanized steel sheet, color sheet Thickness of Coil Sheet0.3 0.8mm Main Motor Power5.5kw Forming Speed10-15m/min Hydraulic Station Power3kw Quantity of Stands18 Hydraulic Pressure10~12Mpa Controlling SystemPanasonic PLC Index Error of Length10m±2mm Total Weight7T Voltage380V 3 phase 50Hz Features of this Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine lower cost high efficiency reliable working low energy consumption Components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine steel strip supporting frame Feeding platform Automatic shearing system Hydraulic system Steel strip unfolding system Computer control system (imported computer) High-precision automatic counter Receiving table Suitable process material: colored steel sheet, aluminium steel sheet, and galvanized steel sheet Optional components of the Metal Roofing Rain Guttering Profile Gutters Roll Forming Machine Manual uncoiler frame in different tons Hydraulic automatic uncoiler Working space and workman for the equipment: 1. Ground-level land 2. 5T overhead travelling crane 3. Space for storing the material 4. Space for laying the machine 5. Road for vehicle moving 6. Workman: 2, operator and porter
Products made by this machine is easy to install, used together with different colors can make It appear dye-in-the-wood individual character. Width of 75, 100, 150, 200, and 300 c-shaped keel Can be assembled arbitrarily, and they are connected tightly.They can be fixed on the device which Is specially used for keels, they can tear down individually. Products made by this machine are suitable to use as building decorations, especially Suitable to use in bedroom, kitchen, washroom, corridor and so on. 1.Processing materialPpgi, gi 2.Processing thickness(mm)0.5-1.6 mm 3.Material of rollers 45# steel, with hard chrome coated 4.Diameter of shaft 40mm 5.Production speed 0-25m/min 6.Roller driven Gear transmission 7.Cutting model Hydraulic profile cutting 8.Length measurement Encoder 9.Control style Plc 10.Operation model Button + touch screen Technical parameter of product line: 1. Applied plank stuff: color armor plate 2. Applied slab thickness: 0.3-1.0mm 3. Charge in width: 1000mm 4. Line speed: 0-14m/min 5. Rolling rows: 16rows 6. Rolling diameter: 70mm 7. Dimensions: 8.5m*1.5m*1.6m 8. Weight: 5t 9. Power: 4kw+3kw Equipment parts 1. Steel strip supporting frame 2. Feeding platform 3. Automatic shearing system 4. Hydraulic system 5. Steel strip unfolding system 6. Computer control system (imported computer) 7. High-precision automatic counter 8. Receiving table
