Construction: the bap 500-iii type aggregate consists of a pump with spiral casing having
An opened mixed flow impeller, and a diesel engine which are connected by a flexible
Coupling. In the discharge nozzle of the pump casing there is a flap valve which is adjustable
By means of handwheel. Priming of the pump casing at starting is by means of an exhaustoperated
Gasjet air pump. The cover age of the engine is made of welded steel sheet
Construction with two lockable doors. The pump and the engine are mounted on a wide
Sledge runners. This solution ensures safe operation of the unit even on wet ground. The
Engine is equipped with a mechanical starter so at operating there is no need for storage
Battery. The equipment has a protection against overheating, shortage of lubrication and
Fuel and v-belt rupture. In these cases the protection stops the aggregate.
Medium handled: clean water at temperature not exceeding 40 to 45 °c, neutral in
Reaction and silty water containing no large solids. Max. Silt content: 1000 mg/dm3.
Field of application: these pumps are used primarily for land drainage, lifting and irrigation.
However, they can be used advantageously in places where, in default of installed energy
Sources, quick installation and putting into operation is required.
Bearing support: the gear drive and the pump are carried in oil lubricated roller bearings.
Main structural materials: impeller, flap valve and flap valve casing: cast iron.
Suction pipe, spiral casing, gear: aluminium casting.
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Product Description Characteristics: SCP series of self-priming diesel engine pump is an ideal dirty water treatment pump for solid particles. The impeller can let solid particles with diameters below 76mm pass. It is easy to use on ground, finish installation and daily maintenance. Application: dirt drain projects, architecture, paper-making, textile, foods, chemicals, electric power distribution, mining, sewage drain, leather, brewage, non-corrosive and highly-polluted sewage drain. Main Usage:City Drainage, Flood Relief, Firefighting, Emergency, Main Drainage, Exploration, Oil Field, Field Working, Ship, Market, Farm Irrigation, River Sewage, Factory, Garden, Power Station, Sea Water Project, Water Project. Conditions, temperature: 0C~40 C, density 1.2-10 3 kg/m3, pH: 5~9; solid particle proportion 2%; maximum particle diameter: SCP-3 63mm; SCP-4/SP-6 76mm; ambient temperature: 40 C; altitude: maximum 1000m.
Model: 350qzb-1600qzb, 1000-1400qhb Power: 5.5-1500 kw Discharge: 116 -10689 l/s Head: 1.1-16.44 m (3.6- 54 feet) Pump outlet diameter: 350-1400mm (13.7-55.1 inch) Dia. Of impeller: 267-1540mm (10.5-60.6 inch) Rotate speed: 485-1450 r/min Angle of impeller installation: from -6 deg. To +6 deg. Ph value: 6-9
Model: 350qzb-1600qzb, 1000-1400qhb Power: 5.5-1500 kw Discharge: 116 -10689 l/s Head: 1.1-16.44 m (3.6- 54 feet) Pump outlet diameter: 350-1400mm (13.7-55.1 inch) Dia. Of impeller: 267-1540mm (10.5-60.6 inch) Rotate speed: 485-1450 r/min Angle of impeller installation: from -6 deg. To +6 deg. Ph value: 6-9
Submersible sewage pump Technical parameter: Model: qwb, Discharge: 5 to 6000 m3/h (1.4-1666.7l/s) Lift head: 6 to 80 m (19.7- 262.5 feet) Max. Rotary speed: 2900 r/min Pump outlet diameter: 50-600mm (2-23.6 inch) Temperature: -5 to +50 deg. C Maximum system pressure:
Submersible sewage pump Technical parameter: Model: qwb, Discharge: 5 to 6000 m3/h (1.4-1666.7l/s) Lift head: 6 to 80 m (19.7- 262.5 feet) Max. Rotary speed: 2900 r/min Pump outlet diameter: 50-600mm (2-23.6 inch) Temperature: -5 to +50 deg. C Maximum system pressure:
Nema Standerd Submersible Pumps And Motor Available 4" & 6" Submersible Motors & Pumps with NEMA Standerds. Available Customised Design For OEM Supply Also. SALIENT FEATURES: Easy To Install, Highly Efficient Motor & Pump, Law Power Consumption, Specially Design For Wide Voltage Range, Corrosion Resistance Stainless Steel Motor & Pump Body, Use Graded Varnish To Reduce Corrosion In Stator, Rotors Are Dynamically Balanced With More Than 2850 rpm To Reduce Vibration, Long Life And Negligible Maintenance Due To High Precision Work, Rotor Are Painted With Special Epoxy Paint For Prevent Corrosion Effect For Long Time, Noiseless & vibration free motors, All Parts Machined On CNC Machine Only
