Here are details of our product
What is the distance between the columns.
1. The distance between column is 7 feet.
Detail of the column.
2. Columns are 6x6 inches (150x150 mm), use 7 pieces of 3 mm steel bar with stressing system, length is depend of your requirement.
Detail of erection.
Make a foundation for columns of 2x2x2 feet and feel with concrete, then insert sheet in between two columns.
Size and thickness of the panels
3. 7x1 feet and 2 inch thickness
A sketch showing the panels details.
4. Length 7 feet (2100 mm), height 1 feet (300 mm), width 2 inch (50 mm), use 3 mm steel bar with stressing system.
Technical details of the product.
5. Vertical concrete posts as well as horizontal planks is caste using pre-stress technology with designed concrete mix to achieve maximum durability and strength.
Time of delivery
6. 3-4 days after receiving order.
Weighted
Supplier: Precast compound wall, fencing, aerocon panel
Services: Fabrication.
Supplier: Precast boundary wall , precast compound wall, readymade rcc walls , concrete wall, cement wall
Buyer: High tensile prestressed wires , cement
Supplier: Precast Compound Wall, Labour Quarters, Kerb Blocks, Drainage Cover Slab, Concrete Bench, Tree Guard, Fencing Pole, Balusters
Conecc AAC blocks weight is 33% lighter compared to traditional bricks and depending on project design, savings up to 20% in structural costs can be achieved, due to reduction of dead load. CONECC AAC BLOCKS COME IN 4 STANDARD SIZES: 600mm x 200mm x 100mm 600mm x 200mm x 150mm 600mm x 200mm x 200mm 600mm x 200mm x 225mm
Supplier: Aac blocks, wire mesh, precast compound wall & m sand, traditional blocks or clay bricks
Services: Manufacturer
Buyer: Cement
Supplier: Concrete block making machine, vibro table, flyash brick making machine, concrete mixer, pan mixer, colour mixer, brick pallets, paver moulds, colour pigments, silicon hardener and shiner for paver blocks, mini crane, concrete mixer cum hoist, hollow block making machine, plastic sheets for shuttering, concrete bench moulds, precast compound wall moulds
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
325 425 525 Portland cement Specification Sulfate Resistant Portland Cement SRPC also named Sulfate Resistant Cement SRC is one of hydraulic binding materials can resistance to sulfate ion attack Type High Sulfate Resistant Cement PHSR and Moderate Sulfate Resistant Cement PMSR Grade 325 425 Application To make concrete of sulfate resistance marine concrete maritime works To make cement boards precast cement products cement pipes precast concrete pile shop fabricated members Sea water attack resistance projects for example sea wall dam mariculture project sea water desalination project oceanarium etc Chemical resistant engineering concrete To make sulfate resistant concrete engineering of harbor water conservancy underground tunnel drainage pipe diversion works road and bridge foundation etc
Supplier: Wall compound precast, RCCC products, garden cement benches, fitting of readymade boundaries, ready made rooms
