Plastic Protective Wall Guard

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

Type - Other Watering & Irrigation Model Number - IR161020-2 Material - Plastic Diameter - 16 MM Wall thickness - 1,0 MM Flow rate - 2 lph Packaging - 400 meter Dripper spacing - 20 CM

Material: PE, PVC Roll: 1.82 x 100 m; 0.92 x 100 m Sheet: 10 x 10 m ; 3.6 x 5.4 m Quantitative: # 1000 ; # 3000 Color: Blue Packing: dup-rolls (Rolls); OPP Bag (Sheets) Details: eyelets Other: OEM

Conventional tanks (concrete or mild steel) are prone to aging, wear and corrosion. Concrete can crack when exposed to erosion and natural disasters, leading to water contamination and leakage â?? and usually canâ??t be repaired. MS rusts easily and its also easy heat conductor. FRP â?? Fiber Reinforced Polymer is a strong but light weight glass fiber reinforced plastic composite used in the aerospace, automotive, marine and construction industries. It has a high-strength to weight ratio, an extremely long lifespan, and easy to maintain as well as heat resistant. FRP sectional panel tanks provides all types of advantages which other liquid storage methods doesnâ??t. These tanks are DURABLE, LEAK-FREE, COST-EFFECTIVE OVER LIFECYCLE as well as EASY TO INSTALL, RECONFIGURE AND RELOCATE. This is an ideal option for a wide range of usage including potable water storage, food and factory production, commercial mining, fire protection, industrial liquids, rainwater harvesting, seawater storage, and any other kind of liquid and granular storages.

Product Description A 45 degree elbow is a pipe fitting that is used to change the direction of a pipe by 45 degrees. It is typically made of steel, stainless steel, or plastic, and can be threaded, welded, or socket-welded to the ends of the pipes. 45 degree elbows are commonly used in plumbing, HVAC, and other piping applications. Technical Specifications The technical specifications of a 45 degree elbow will vary depending on the material, size, and type of fitting. However, some common specifications include: Inside diameter (ID): The ID is the diameter of the pipe that the elbow will fit. Outside diameter (OD): The OD is the outer diameter of the elbow. Radius: The radius is the distance from the center of the elbow to the inside of the bend. Wall thickness: The wall thickness is the thickness of the elbow. Type: There are two main types of 45 degree elbows: long radius (LR) and short radius (SR). LR elbows have a longer radius than SR elbows, which makes them more flexible and easier to install. Material: The most common materials for 45 degree elbows are steel, stainless steel, and plastic. Steel elbows are the most durable, but they are also the heaviest. Stainless steel elbows are corrosion-resistant, but they are more expensive than steel elbows. Plastic elbows are the lightest and least expensive, but they are not as durable as steel or stainless steel elbows. Applications 45 degree elbows are used in a variety of applications, including: Plumbing: 45 degree elbows are used in plumbing systems to change the direction of pipes. They are commonly used in bathtubs, showers, toilets, and sinks. HVAC: 45 degree elbows are used in HVAC systems to change the direction of air ducts. They are commonly used in furnaces, air conditioners, and heat pumps. Process piping: 45 degree elbows are used in process piping systems to change the direction of fluids. They are commonly used in chemical plants, oil refineries, and power plants. Other applications: 45 degree elbows can also be used in other applications, such as irrigation systems, fire sprinkler systems, and swimming pool systems.