Shear/scratch Tester

Introduction: Scratch Tester is applied to the scratch resistance performance evaluation of single coating or complex coating system in insulated color coated sheet. It will be known the coating scratch resistance performance by evaluating whether the coating is scratched by tungsten carbide hemispherical stylus with a certain weight or the maximum load of the coating which can not be scratched. The Scratch Tester of BEVS is complied with the standards of ISO1518, BS3900. Features: Big LCD design,touch-screen operation Adjustable work platform---More convenient Display the test result on the conductive substrate High Hardness Scriber---More durable Special design for sample clamp---Equipped with ruler Show the testing procedure with real time graph Technical Specification: Scratch Speed: 30-40 mm/sec Moving Distance: 65 mm Power: 220V/50Hz or 110V/60Hz Stylus: Tungsten carbide hemispherical stylus, diameter 1mm Metallic test panel size: 100Ã?150Ã?0.2mm(LÃ?WÃ?H) Order Information: BEVS 2801--------Scratch Tester BEVS 2801/P/001--Tungsten carbide hemispherical stylus, diameter: 1mm

Scratch Grinding Tester Automobile line inspection equipment Wire and Cable Detection Equipment It is applicable for assessing the scratch-resistant performance of automobile wire insulation with external forces in line with the requirements of GB/T12528-2008. Main parameters: 1. The scratch grinding device exercises in two directions along wire axes with a stroke above 10mm 2. Exercise frequency: 50~60 cycles/min 3. Minimum distance between test points and test point and test sample end: >10mm; rotation angle of test sample: 90° 4. Length of test sample: Test sample which is about 750mm is firmly fixed to a steel anvil 5. Weight: 400, 700, 1000g (weights applied to scratching needle) 6. Function: The device will stop when the scratching needle grinds through insulation and comes into contact with conductor

Introduction: resistance performance evaluation of single coating or complex coating system in insulated color coated sheet. It will be known the coating scratch resistance performance by evaluating whether the coating is scratched by tungsten carbide hemispherical stylus with a certain weight or the maximum load of the coating which can not be scratched. Dimension(cm)of packing 60*44*31 Gross Weight(KG) 20

Standard Features: Pneumatically driven, moveable platform Control knob operation Five independent spline-shaft fingers with support rest 9-piece weight set (2N, 3N, 4.5N, 5N, 6N, 7N, 10N, 15N, 20N) “Gripping” spring clamp specimen hold-down Replaceable specimen platform protective guard Electronic timer accurate to 1/100 second Air regulator control with built-in lubricator

Function and usage It can set with 5 different temperature spots to do heat sealing, select the optimal heat healing temperature, and can also set the same temperature to speed up the heat sealing. Instrument structure: The structure of the heat-sealing tester is composed of 4 parts: pneumatic drive system, heat-sealing equipment, temperature adjustment system and time adjustment system. Pneumatic drive system: It includes pressure gauge, guide stick, cylinder, pneumatic valve, pressure regulating handle and so on. You can pull the pressure-regulating handle outward, rotate to the right side to adjust the heat sealing pressure to a high value, and rotate to the left side to reduce it. After setting the pressure, please press the handle to the side of mainframe to lock the air pressure. Heating-seal device It is composed of the upper and lower heat-sealing sticks, of which the upper one is connected with a cylinder. There is an insulating plate in the upper part, which can prevent heat transmit to the cylinder. The heat-sealing stick is made of aluminum, and the center is heater. There is a silica gel plate in the upper part of the lower heat-sealing stick, which can mitigate pressure impact during heat sealing. Temperature measurement system was installed at the back of the heat-sealing stick. Temperature adjustment system: The upper temperature controller controls the temperature of upper heat-sealing stick, and the rear temperature controller controls the temperature of lower heat-sealing stick. The temperature can be set at will through adjusting the button on the dial plate. Time adjustment system: Time adjustment system: The heat-sealing time can be set at will through adjusting the button on dial plate. The setting scope of time is 0.01s to 999.9h. Press the foot switch under the manual state, and the heat-sealing stick will be pressed together. Under the automatic state, the press-fitting time of upper and lower heat sealing sticks are controlled by a timer automatically, it can automatically recover later. The unit of timer is 0.1 second in general. There is time adjusting button on the panel of the timer, and the heat-sealing time can be adjusted at will. Specifications Power : AC220V 50HZ Compressed air: 8kg/cm2 Heat sealing plane: 300mm10mm slick (With silicon pad in lower seal stick) Heat sealing temperature: room temperature 20~300C (Precision 1C) Heat sealing time: 0.01s~99.99h Heat-sealing pressure: 0~0.8Mp. Dimension: 700(L)mm400(W)mm540(H)mm Weight: Desktop 30Kg. 700mm(L)X400mm(B)X540mm(H)

Scope Applied standards: gb/t269, iso2137, astmd217, ip50 Applied range: the grease by mechanical shearing and consistency change, then with the cone penetration tester were measured to determine the mechanical stability of grease. Features 1. With integrated design, easy operation and maintenance; 2. It adopts imported motor drive, low noise, long life; 3. With automatic timing to the alarm system; 4. Using the results of the double bomb, to facilitate the operation of parallel experiments. Technical parameters 1. Shear rate: 60 times / min; 2. The working stroke: 67 ~ 71mm; 3. The number of significant count: 0 to 10 million times; 4. Count method: automatic; 5. Motor power: 370w

Supplier: Castrator pliers, bull holders, bull nose rings, de-horner, emasculator pliers, ob instruments, ear tattooing pliers, balling guns, foot rot shears, pig instruments, grooming instruments, hoof knives, farrier nipper, hoof testers, fire tongs

Film Shrinkage Test Equipment Film Shrinkage Tester GBK-D1 Film Shrinkage test, known as linear thermal shrink test or free shrink test, is used for analyzing the effect of temperature on heat shrinkable films made from polyethylene, ethylene copolymers and their mixtures. Basically, shrinking force, contracting force and shrinking ratio can be measured in such determination. GBPI Film Shrinkage tester conforms to the multiple national and international standards: ASTM D2732 - Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting ISO 14616 - Plastics Heatshrinkable films of polyethylene, ethylene copolymers and their mixtures Determination of shrinkage stress and contraction stress DIN 53369 - Testing of plastic films determination of the shrinking stress Film Shrinkage Test Equipment GBK-D1 is used to determination of the degree of unrestrained linear thermal shrinkage and dimensional stability at different temperatures. Widely used in industries of plastic material, plastic products, petroleum, chemicals, research institute, inspection agency and so on. Principle This tester uses the principle of air heating to connect the tested sample to the tension sensor and displacement sensor. After reaching the maximum shrinkage force, it is placed in an external test environment with an ambient temperature of 23 to cool down. The reference temperature, shrinkage force and displacement are recorded, and the recorded data can be used to determine the optimal shrinkage conditions of the film. Standards ISO 14616, ASTM D2732, DIN 53369

Supplier: Tensile tester, heating-seal tester, friction tester, oxygen permeation analyzer, water vapor permeation analyzer, gas permeation analyzer, inverted pressure sterilized boiler, impact tester, electronic thickness tester, scratch-resistant tester, drying oven