Our jiggler siphon pump are made of high quality aluminum or brass copper. We manufacture both the ½ inches (12mm) and the ¾ inches (19mm) model in high quality red brass copper or pure aluminum.
Hoses are supplied from the highest quality food grade, to the most economical available.
We are a specialist manufacturer of jiggler siphon pumps with our manufacturing line based in the guangdong region of china.
Supplier: Jiggler siphon pump , caster wheel, hardware tool
1. Introduction The kitchen waste solid liquid separator uses kitchen/fruit and vegetable organic waste as raw materials, through the dual shaft Roller shredding, squeezing dehydration, oil-water separation and other comprehensive treatment technologies for rapid decomposition. After setting the parameters It can run automatically without manual operation. It can achieve rapid waste reduction, and the sewage can be discharged after subsequent treatment It is used as raw material for biomass fuel after recycling. 2.Working principle 2.1. After the kitchen waste enters the equipment, it is firstly evenly crushed by a two-axis roller shredder, and the particle size after shredding at 10-20mm, the teeth of the shredder are made of high-strength alloy, and the size of the shredded kitchen waste is uniform and small tableware, bones and other hard objects that are not fully quantified are broken at the same time to avoid malfunctions during the operation of the equipment. 2.2The follow-up dehydration of slag with small particle size is more complete, the amount of reduction is more, the oil extraction rate is high, and the overall operation efficiency of the equipment is high. 3.After being shredded, the slag automatically enters the screw press dehydrator. The dehydration process of the screw press dehydrator is divided into two stages. In the first stage, the spiral auger is used for dehydration. The spiral auger is divided into three sections: transmission section, compression section and discharge section. 3. The extruded liquid of the squeeze dehydrator is transferred to the oil-water separator through the diaphragm pump, using the kinetic energy of the water flow to connect continued collision, the grease from small to large, thereby accelerating the movement, so that the oil and water of different proportions can be shunted and layered, which helps after the oil and water are separated by the density difference, it enters the next stage. The waste water makes turbulent movement under the siphon effect along the spoiler. After flowing from the overflow weir into the collection tank and discharged through the drainage port, the oil beads in the water gather and flow upward, floating in the oil-water separator.
Scope FDQ-0301 laser particle size analyzer based on physics Fraunhofer diffraction and Mie scattering theory basis. This theory can be simply understood as: travels in straight lines parallel laser beam blocking particles encountered in the communication process, the phenomenon of diffraction and scattering, and small angle light scattering large particles, small particles of light scattering angle is large. Figure 1-1 shows the diffraction pattern formed by individual particles, the larger the particle diameter, the smaller the center of the bright ring, the smaller the particle diameter, the larger the center of the bright ring. Use photo detector array receiving light at different angles, for the corresponding angle, its energy is set corresponding to the diameter of the particles occurs diffraction (scattering) caused by the respective other angle light will reflect the strength of the corresponding diameter of the particles throughout the assembly of particles occupies proportion, according to the intensity of the received scattered light at different angles, you can perform anti-particle distribution of the sample between the relative content and various size fractions. Features 1. Up to 82 sampling channels to improve the resolution of the test results; all the photovoltaic device fabricated on a single silicon chip, to ensure the life of the photovoltaic array; cross-sector arrangement, increasing the light receiving area, improves the sensitivity ; 2. micro injection method, using a peristaltic pump automatic loop injection mode, using siphon pump automatic cycle injection mode, to meet different customer test requirements, the instrument comes standard MS-01 micro-injector device; 3. The single lens full scale measurements, all optical components are mounted on reinforced base before fastening a good optical system is shipped, the instrument more stable performance; 4. Imported semiconductor lasers, has a long life, stable optical parameters, not afraid of vibration and a series of advantages, continuous working time of up to 24 hours, to meet user requirements for large continuous load test. Technical Parameters 1, the test range (um): 0.15-400; (0.4-1100,0.1-450,0.25-650, 0.4-1100) 2. Repeatability:
