Ekotank Star Water Tanks

Hammered Copper Water Tank

BCPL manufactures 990 Ltr water capacity tanks. The manufacturing unit is equipped to design and manufacture tanks up to 3000 liters of water capacity. These tanks are heat-treated in a state-of-the-art NC control furnace and painted with polyurethane paint with an undercoat of epoxy primer. The powder coated surface is also supplied on request. These cylinders are supplied to Indian oil and marketing companies such as Indian Oil Corporation, Hindustan Petroleum, Bharat Petroleum and to companies such as TOTAL, Super Gas and exported to other countries.

Conventional tanks (concrete or mild steel) are prone to aging, wear and corrosion. Concrete can crack when exposed to erosion and natural disasters, leading to water contamination and leakage â?? and usually canâ??t be repaired. MS rusts easily and its also easy heat conductor. FRP â?? Fiber Reinforced Polymer is a strong but light weight glass fiber reinforced plastic composite used in the aerospace, automotive, marine and construction industries. It has a high-strength to weight ratio, an extremely long lifespan, and easy to maintain as well as heat resistant. FRP sectional panel tanks provides all types of advantages which other liquid storage methods doesnâ??t. These tanks are DURABLE, LEAK-FREE, COST-EFFECTIVE OVER LIFECYCLE as well as EASY TO INSTALL, RECONFIGURE AND RELOCATE. This is an ideal option for a wide range of usage including potable water storage, food and factory production, commercial mining, fire protection, industrial liquids, rainwater harvesting, seawater storage, and any other kind of liquid and granular storages.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.