Synchronous Round

Conveyor belt Mechanical transmission

Models have: A, B, V, C, Y, O, SPA, SPB, SPC, SPZ, XPA, XPB, XPZ, XPC, PL, PK, PJ, PH, PM, 3V, 5V

1. Teflon mesh with the main features: 1. Temperature of - from the low-temperature high-temperature -140 íµ to 260 íµ 2. Permeability - the permeability rate of a conveyor belt to reduce the heat consumption, improve drying efficiency 3. Resistant to corrosion - on the majority of the chemicals and solvents are not affected 4. Anti-adhesive - resin, paint, chemicals, such as almost all the adhesive material can be Easy to remove 5. Flexural fatigue resistance - there is a high tensile strength and resistance to bending fatigue performance, can By the use of the smaller round. Two. Teflon mesh scope of application Textile printing and dyeing, printing drying belt, screen printing, uv dryer, uv Series of light solid machine, offset machine, dryer song, non-woven fabric drying machines, high-cycle Wave dryer, food bakery machine belt, drying room temperature, flux-based ink quickly Fast drying and dry goods such as general moisture

Supplier: Industrial belt, transmission belt, timing belt, synchronous round of, pulley, conveyor belt, special belt

Introduction APEC Brand AIW series Hydraulic Ironworker is widely used in steel structure, high voltage tower, telecommunication tower, large rigid frame bridge, military and air craft and other metal fabricating industries. It also can be used in vocational school for teaching purpose. APEC Brand AIW series Ironworker features multiple functions, including: punching all kinds of holes (round hole, square hole, oblong hole), louver punching, steel plate punching, flat bar punching, angle steel punching, C-channel punching, H-beam punching, I-beam punching, profile steel shearing (channel shearing, I-beam shearing, round/square bar shearing, flat bar shearing, T-bar shearing, steel plate shearing, angle steel shearing), notching, press brake, angle steel notching , bending, pipe notching. It comes standard with: quick-change coupling nut & sleeve, squaring arm with scale, electronic back gauge, gauging table with stops, punching base table, safety guards and more.We can design any special tools according to your metal fabricating requirements. APEC Brand AIW-E series is improved machine on the base of standard AIW series. It goes along with automatic holding system and temperature cooling system. Automatic Holding System: There is automatic holding system in angle steel shearing and plate shearing work position. The holders will fix the position of work-piece, in this way, the accuracy is better and more safety for workers meanwhile save time and Improve working efficiency. Temperature cooling system:Through the temperature monitoring screen you can read the temperature of oil, 55 degree is our default configuration, once the machine is working, oil temperature goes higher than 55 degree, the cooling system inside will run automatically to decrease temperature in order to protect machine. APEC Brand AIW-L series is improved machine on the base of standard AIW-E series. It also goes along with automatic holding system and temperature cooling system. At the same times, punching position and shearing position can work synchronously. Features 1. High Quality Components & System a. Main Electrical component: Schneider, Germany. b. Valve: Yuken, Japan c. Pump: Atos, Italy d. Oil Seals: NOK, Japan e. Timer Relay: OMRON, Japan f. Wiring Terminal Block:WEIDMULLER, Germany g. Motor: Weiteli, China 2. Cost Effective AIW SERIES Hydraulic Ironworker With Very good price/performance ratio Various AIW SERIES Hydraulic Ironworker capacity from 45T to 400T to meet your requirement. 3. Stable Performance & Reliable Quality AIW Series Hydraulic Ironworker use hydraulic transmission. Light weight, low noise, reliable performance. 4. Simple Operation The operation of hydraulic ironworker is controlled by foot switch. Technical Parameters: Accessories: a. A pair of round hole punching die b. A set of angle steel blade c. A set of square and round bar blade d. A set of shearing plate blade e. A set of notching blade The above punching and moulds will be installed in the machine. For other dies and blades, customers need to order Installation & Operation Training APEC will provide you 1-7 day installation and operating training in our factory. Training After-sales service 1. Technical documents All labels on machines and lay-out drawings, Electrical diagram, Operation Manual, will be in English. The seller should send all necessary files to the buyer since the third week since project execution. All documents in hard copies should be also shipped with machines together. 2. Arrangement for inspection, installation and testing work a. After all machines are delivered to customer¡¯s factory; Buyer is responsible for all preparation work, e.g. electricity supply, water supply, labors and cranes, etc. b. The buyer will prepare for visa application for their engineers, who are responsible for guide of machine installation and testing at the Buyer¡¯s factory. c. The Buyer will buy the round-trip air ticket for Engineer if visa application is approved. The buyer is also responsible to bear expenses generated, e.g. visa formalities, meals, accommodation and allowance of USD80 per day for each engineer. d. Engineer will give free training lessons to labors in buyer¡¯s factory. 3. Quantity and quality guarantee a.Quantity/Quality Discrepancy to destination port during transportation: In case of quality/quantity discrepancy to destination port in transportation, the buyer should file claim within 30 days after the arrival of the goods at port of destination. The seller will not be responsible for any discrepancy of the goods caused by shipping company and other transportation organization and/or post office. b.Guarantee period and after-sales services: 13 months since date of bill of lading During this guarantee period, the seller will provide spare parts without any charge in case of quality discrepancy caused by us. If the malfunctions are caused by your incorrect operations, the seller will provide the buyer spare parts at cost price. c.Long-term service: The seller will charge the buyer cost price of spare parts beyond one year and provide long-term technical guide. FAQS: 1. Payment Terms T/T, L/C at sight are acceptable by us. 2. Price Terms It is up to your requirement. EX-WORS, FOB, CIF, CFR and so on are acceptable by us. 3. Delivery Time 25 working days from our accountant confirm your deposit payment. 4. Shipment Condition We will arrange the machine production from our accountant confirm your deposit payment. The deposit is 30% of the contract. The balance should be paid up before loading machines. 5. Warranty 13 months quality guaranty for the main spare parts, not include quick-wears parts, like blade, punch, die and so on. If the parts of machines have problems, which are caused by its own quality, we will provide the accessories for free. General View of machine Mutiple Functions Machine pictures Work pieces Hydraulic ironworker, ironworker, lathe, punching, cutting, notching, bending, machine, process, metal steel, plate cutting, Angle cutting, plate bending, shearing, hydraulic ironworker machine, mechanical ironworker, ironworkers, iron worker, steel worker, metal worker, shearing machine, cutting machine, sheet metal punching machine, notching machine, guillotine machine, bending machine, press brake, c-channel bar cutting machine, H-beam cutting machine, angle bar cutting machine, dual hydraulic cylinders, single cylinder, punch and shear station, rolling machine, band saw, pipe punching, tube bending, pipe notching, machine tool. Model AIW-60/L(Q35Y-16) AIW-90/E/L(Q35Y-20) AIW-120/E/L(Q35Y-25) AIW-160/E/L(Q35Y-30) AIW-200/E/L(Q35Y-40) AIW-250/E/L(Q35Y-50) Processing Capacity (KN) 600 900 1200 1600 2000 2500 Material Tensile Strength (Mpa) ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 ¡Ü450 Ram Stroke(mm) 80 80 80 80 100 100 Number of Stroke(times/min) 8-22 8-22 8-22 8-22 8-24 8-24 Throat Depth 300 355 400 600 550 550 Shear Angle 7¡ã 8¡ã 8¡ã 8¡ã 8¡ã 8¡ã Flat Shearing Max. Shearing Capacity (thickness* width (mm) 16¡Á250 20¡Á330 25¡Á330 30¡Á355 35¡Á400 40¡Á450 8¡Á400 10¡Á480 16¡Á600 20¡Á600 25¡Á700 30¡Á750 Bar Shearing Square Bar(mm) 40 45 50 55 60 65 Round Bar (mm) 45 50 60 65 70 80 C-channel (mm) 126 160 200 280 300 320 I-beam (mm) 126 160 200 280 300 320 Angle shearing 90¡ã shearing (mm) 120¡Á12 140¡Á12 160¡Á14 180¡Á16 200¡Á18 200¡Á20 45¡ã shearing (mm) 70x8 70x10 80x7 80x10 80x10 80x10 Hole Punching Max. Punching Capacity (diameter* thickness) (mm) ¦µ25*16 ¦µ30*20 ¦µ35*25 ¦µ38*28 ¦µ40*35 ¦µ40*40 Motor (KW) 4 5.5 7.5 11 15 18.5 Dimension(mm) Length 1650 1950 2350 2680 2800 3200 Width 800 900 980 1060 1260 1440 Height 1780 1930 2100 2380 2420 2450 Weight 1800 2600 4800 6800 9200 12800