Glass Evacuated Solar Collector Tube

Difference between three high efficiency solar vacuum tube (effective tubes, high cold tube, high temperature special efficiency tube)and ordinary tube:

Absorption of heat membrane layer is difference between these two kind of tubes. (Absorption of heat membrane layer is the key part of vacuum tubes.) Absorption of heat membrane layer of three high efficiency solar vacuum tube is interference membrane, common tube is gradient membrane. The difference is mainly for interference membrane and the gradient membrane distinction.

1. Fundamental distinction: membrane layer structure is different, the principle of the absorption of sun's rays result in differently. gradient membrane, for multilayer, its absorbing layer is generally 9 layers. It to the sun's rays are layered absorption, and its absorb the light performance gradually become tall. Because the gradient structure, launch with increasing temperature rise than work, that temperature in 300 to 500 C than when launch greatly increased. The aluminum ions and absorbing layer in high temperature condition, lively nature greatly enhance the, and develop a drift. This happened in the internal structure of membrane layer caused confusion, coating began to aging. In the long run, the high temperature condition, membrane layer can fall off, thereby affecting the vacuum tube heat efficiency and life integrating.
Interference membrane, its absorbing layer altogether 2 layer, among two layer membranes, because the metal content between the different and interfere ratio effect, make absorption ratio increase, launch ratio decrease. Plus effect of reduce emission from minus reverse layer, thus achieve more higher absorptance and reducing the role of launch ,greatly improved collection thermal efficiency.

2.Features: Absorptance of three high efficiency solar vacuum tube increased by 12%, and launch reduced by 30 to 40 percent, the super absorbing, heat loss less, warming faster. Efficient tube, the super absorbing, thermal efficiency is high, warming faster, in the same light conditions, can create more and higher temperature water than common tubes ; high cold tube, copper ions for the launch of aluminum ion mantua, so low 0.2 thermal loss rarely, in high cold environment can still work normally. hot water turn out as usual under- 30 C. high temperature special efficiency tube, because the membrane layer stainless steel ion high temperature resistant, fight air drying. Membrane layer under the condition of the 400 C, not attenuation, not aging, discoloration.
In the same light conditions, ordinary tube heat absorption is lower than three high efficiency solar vacuum tube, can't even meet requirements that wash bath; In lower temperature, heat loss is bigger, collection hot effect is reduced, affect the normal use; Especially in the empty sun over 270 C, membrane layer began to aging, fall off, absorption rate drastically reduce, life shortens greatly.

3.Technology: high temperature special effects tube, high cold tube, efficient tube used respectively to three target, double target, single target magnetron sputtering craft; Ordinary tube typically use the single target magnetron sputtering technology.

4, appearance: A, Mouth of tube, here membrane layer above 800 C high temperature condition sealing off part is inevitable.
As high temperature special effects tube has high temperature resistant, only 1 cm long without membrane layer in mouth of tube, while others without membrane layer for without high temperature resistant, tube membrane layer falls off the length is about
2.5 cm

B, Inner tube color: with macroscopic observation, high-temperature tubes and high cold tube for internal color is kermesinus (for membrane layers bottom is copper); the bottom And efficient tube and ordinary tube are white (for membrane layer bottom is aluminum).
Anyhow, interference membrane is the new breakthrough basis of gradient on membrane technology ,it is the great innovation in coating technology progress and become current global, interference coating of the most advanced coating technology. But also to the vacuum coating technology bring epoch-making change. Especially with the high temperature effects made interference membrane, can also be used for cooling tube, dry, seawater desalination, opened up the update for vacuum tubes wider application fields.

Solar collector tube introduction
Feature:
1 Quality warranty :15 years
Quickly thermal collecting efficiency.
It works fine under cold weather and area.
Three kind of solar collector:
Common :evacuated collector tubes.
High-efficiency: Three-target evacuated collector tubes: blue and black-golden
High-efficiency: Three-target evacuated collector tubes: purple-golden (purple and golden)
Solar evacuated collector tubes technical data:
Dimension: 47: 58
Material of tubes: 3.3 high borosilicate: 3.3 high borosilicate
Glass expansion ratio: 3.3¡¾0.1X10-6 k-1: 3.3¡¾0.1X10-6 k-1
Outer diameter of tubes: 47¡¾0.7: 58¡¾0.7
Inner diameter of tubes: 37¡¾0.7: 48¡¾0.7
Thickness of glass: 1.6¡¾0.15: 1.6¡¾0.15
Transmittance: 0.89: 0.89
Selective coating: SS-CU-AL-N/AL: SS-CU-AL-N/AL
Adsorptivity: 0.86(AM1.5): 0.86(AM1.5)
Emissivity: 0.080(80¡¾5): 0.080(80¡¾5)
Vacuum degree: 5.0 X 10-3Pa: 5.0 X 10-3Pa
Collecting performance under sunshine: 190m2/kw: 190m2/kw
Hailstone resistance: 25mm: 25mm
Start up fast and collect solar energy fully
Unique super pure copper surface,allowing reflection and minimal heat loss.
High level vacuum ensure operation under cold weather.
Long time warranty to 15 years.



10pcs/Carton.
Applications: superior heat resisting products and crafts.


15-20KG/Carton.