Wire jump prevente
The wire jump preventer (wire roller-nt series) is used for a radical change of direction and adequate guidance and prevent the wire jumping during the winding process. The precision ceramics circle inside has an ultra-fine polishing degree ra0.2. There is a high-speed bearing in this porcelain circle which can control the sliding distance between enameled wire and the circle under 0.2mm, protect the film and assure the beating of the enameled wire in a very small scope to stabilized the tension.
Supplier: Motor nuzzle, tungsten carbide nozzle, ruby nozzle, wire jump preventer, wire roller, ceramic roller, ceramic eyelet, tension control, tension meter, barrel coiler, ceramic stick, ceramic tube
Supplier: Motor nuzzle, hard a alloy nozzle, ruby nozzle, wire jump preventer, assembled wire roller, ceramic roller, ceramic eyel, tension control, tension meter, barrel coiler, password lock
wire roller ú¦The wire roller (DL series) is the commonly used component for the wire passing, and it is used in the wire passing position of the coil winding machine and the textile machinery as well. The porcelain ring is trapped out of the bearing, it will rotate by the thread and wire passing on the surface of the ring. Thus the sliding friction has been converted to the static friction. But at the start and stop, in order to overcome the inertia, there will be a partial sliding friction. The difference between the usage of wire roller and ceramic ring is: there is a sliding friction between thread, wire and the surface of the ceramic ring, so it is applied for the smaller angle of the wire, lower pressure and other such kind of less demanding occasions. The wire roller is mainly used of static friction (part sliding friction); it is applied for the bigger angle of the wire, a certain pressure and other such kind of higher occasions. Recently, as improved processing technology, ceramic rings can also be used for important occasions, further illustration will be provided when orders. The surface polish degree of the porcelain ring reaches Ra0.2; the beating during rotation is under 0.15. We select the 99% AL2O3 as the material with the hardness of HRa88 and the density of 3.85. There are three types of the wire roller---wire roller (DL series), ceramic roller (NT-2 series) and the wire jump preventer (NT series). Two nylon sidewalls have been put to the both side of the ceramic ring and the bearing, it combines one wire roller. Two ceramic sidewalls have been put to the both side of the ceramic ring and bearing, there is a reverse hook or a ball to prevent the thread jumping out above the ring. The roller which is without the ceramic sidewalls is called ceramic roller. wire roller ú¦The wire roller (DL series) is the commonly used component for the wire passing, and it is used in the wire passing position of the coil winding machine and the textile machinery as well. The porcelain ring is trapped out of the bearing, it will rotate by the thread and wire passing on the surface of the ring. Thus the sliding friction has been converted to the static friction. But at the start and stop, in order to overcome the inertia, there will be a partial sliding friction. The difference between the usage of wire roller and ceramic ring is: there is a sliding friction between thread, wire and the surface of the ceramic ring, so it is applied for the smaller angle of the wire, lower pressure and other such kind of less demanding occasions. The wire roller is mainly used of static friction (part sliding friction); it is applied for the bigger angle of the wire, a certain pressure and other such kind of higher occasions. Recently, as improved processing technology, ceramic rings can also be used for important occasions, further illustration will be provided when orders. The surface polish degree of the porcelain ring reaches Ra0.2; the beating during rotation is under 0.15. We select the 99% AL2O3 as the material with the hardness of HRa88 and the density of 3.85. There are three types of the wire roller---wire roller (DL series), ceramic roller (NT-2 series) and the wire jump preventer (NT series). Two nylon sidewalls have been put to the both side of the ceramic ring and the bearing, it combines one wire roller. Two ceramic sidewalls have been put to the both side of the ceramic ring and bearing, there is a reverse hook or a ball to prevent the thread jumping out above the ring. The roller which is without the ceramic sidewalls is called ceramic roller.
ruby nozzle ú¦This product is assembled by the stainless steel main part and the processed stones. It has been widely used in various types of CNC automatic winding machine.The nozzle is installed at the end of the mechanical hand of the winding machine, the enameled wire will go through it and do the winding job under the guidance of its processing. It is not only the indispensable component of the winding machine, but also the key components which are used for ensure the quality of processed products. The main function of the nozzle is the protection of the enameled wire insulation layer. The ruby material has the characteristics of extremely hard and wear-resistant, we do the precision grinding and polishing by using sophisticated equipment under these characteristics, coupled with advanced technology, the roughness of bore, surface and R place will be reached over Ra0.025, therefore the rate of damage will be extremely low. We do the fine mosaic with the good toughness characteristics of the stainless steel. Advantages: good toughness, low friction coefficient of the ruby head, long life. Apply: applicable to fine coil and coil processing of thread . Processing Limit: d1 í¦ 0.2 mm D1 í¦ 0.7 mm ruby nozzle ú¦This product is assembled by the stainless steel main part and the processed stones. It has been widely used in various types of CNC automatic winding machine.The nozzle is installed at the end of the mechanical hand of the winding machine, the enameled wire will go through it and do the winding job under the guidance of its processing. It is not only the indispensable component of the winding machine, but also the key components which are used for ensure the quality of processed products. The main function of the nozzle is the protection of the enameled wire insulation layer. The ruby material has the characteristics of extremely hard and wear-resistant, we do the precision grinding and polishing by using sophisticated equipment under these characteristics, coupled with advanced technology, the roughness of bore, surface and R place will be reached over Ra0.025, therefore the rate of damage will be extremely low. We do the fine mosaic with the good toughness characteristics of the stainless steel. Advantages: good toughness, low friction coefficient of the ruby head, long life. Apply: applicable to fine coil and coil processing of thread . Processing Limit: d1 í¦ 0.2 mm D1 í¦ 0.7 mm
Tungsten carbide nozzle ú¦this product is made by the precision machining with the tungsten carbide materials (superhard alloy). The hardness reached over hra90 degree while the anti-bending degree reached over 2300n/mm. We do the precision grinding and surface treatment to achieve ra0.1 of the bore roughness and the ra0.025 of the r place of both ends. There is a scientific curvature radius design in the both entrance. This design can ensure a smooth transit of the thread. Due to the overall materials processing, and no elevation in the bore, the phenomenon of easy-bending and plugging has been improved comparing with the ruby nozzle. Advantages: high hardness, rigid and impact resistance. Tungsten carbide nozzle ú¦this product is made by the precision machining with the tungsten carbide materials (superhard alloy). The hardness reached over hra90 degree while the anti-bending degree reached over 2300n/mm. We do the precision grinding and surface treatment to achieve ra0.1 of the bore roughness and the ra0.025 of the r place of both ends. There is a scientific curvature radius design in the both entrance. This design can ensure a smooth transit of the thread. Due to the overall materials processing, and no elevation in the bore, the phenomenon of easy-bending and plugging has been improved comparing with the ruby nozzle. Advantages: high hardness, rigid and impact resistance.
Bactericide; Industrial sterilization and mildew prevention; Efficient and broad spectrum bactericide and algicide; It is used to manufacture rubber products such as cables, wires and tires.
0.008mm Insulated Sliver jump wire PCB Repair flying line For iPhone Motherboard PCB Welding Repair Tool. MY-F008 0.008 200M solder wire for motherboard fingerprint CPU IC welding repair. Features: 1. Diagmeter 0.08 mm insultaed copper logic board jump wire. 2. Fully shielded and insulated, Insulated magnet jumper wire. 3. Running Long Jumpers Without Worrying About Shorting Out Components 4. It's made of copper, and not the common enameled wire, the surface is conductive. 5. Durable,Tensile, great for running long jumpers without worrying about shorting out components along the way. 6. Super compacity: for phone logic boards link wire copper and soldering wire for motherboard BGA chip welding repairing. 7. Options: 1 Pcs 0.08mm 50m/200m are available. Product Specifications: 1. Material: Plastic,Metal,Sliver 2. Weight: 0.05kg/0.08Kkg 3. Length: 50m 4. Diagmeter: 0.01mm/0.02mm 5. Color: Metal/Sliver 6. Type: Logic board Jump Wire 7. Application: for Motherboard BGA chip Welding Repairing 8. Customized: Yes 9. Function: Insulated magnet jumper wire for running long jumpers 10. Insulation or: Insulated 11. Type: PCB welding tools 12. Usage: Logic board BGA chip Welding
TX001 Portable Jump Wire Soldering Iron Replaceable JBC T210 Welding Iron Tip for Mobile Phone PCB Soldering Repair, heating up quickly, 2 seconds up to 380 degrees. quick cooling, automatic sleep, QC Quick Charging Adapter, replacing damaged or unusable iPhone motherboard repair. Features: 1. Small size, easy to carry and use, suitable for soldering jump wire/solder wire on the motherboard. 2. Heating up quickly, 2 seconds up to 380 degrees. Quick cooling, automatic sleep, wake up with a touch, 3-gear adjustable temperature. 3. TYPE-C power supply interface, and charge with power bank or other USB power supply. Voltage 5V-12V, current 1A-5.9A is available TX001 Portable Jump Wire soldering iron Specification: Model: Portable Jump Wire Soldering Iron TX001. Voltage: 5-12V. Current: 1-5.9A. Temperature: 0-450 degrees (350-400-450 degrees adjustable). Features: compact, portable, fast heating-up, quick cooling, automatic sleep, adjustable temperature. USB 210 Soldering Iron Features: 1. Three levels of temperature adjustable(350-400-450 degrees). 2. With status light. 3. Support QC protocol, charging head automatic voltage boost 4. Type-c sockets in a gold-plated process, high current does not generate heat. 5. The heating core clamping shrapnel adopts the same material as the JBC handle. 6. Standard 66W quick charger with QC agreement. 7. Lightweight handle, metal button, one key switch. Working Mode: 1. One key switching, three levels of temperature adjustable. 2. Green light mode 350, blue light mode 400, red light mode 450, yellow light is at sleep mode. 3. The green, blue and red light stays on shows it's heating. 4. Flashing green-blue-red light indicates that the temperature has reached the set value.
Sunshine S210 110W Universal Portable Smart Soldering Iron With Universal C210 Series Soldering Tips 2 Seconds to Heat up Smart Sensor Sleep Multifunctional Welding Tool. Features: 1. Portable 110W high power C210 series soldering iron tips, say goodbye to long-term preheating. 2. The soldering iron stand is designed for sleep, prolong the life of the heating core, save power and worry. 3. Cleaning copper wire ball and a heating core cleaning hole can also place a replacement soldering iron tip to prevent loss and quickly replace it. 4. Lead-free soldering iron head conducts heat quickly, oxidation resistance, easy to tin. Plug and play, 2 seconds disassembly and replacement, convenient and fast. 5. The soldering iron is widely suitable for various chip-level maintenance, PCB manufacturing, mobile phone motherboard flying lead desoldering, etc. Specification: Product name: Portable Soldering Iron Model: S210 Handle size: 195 16 15mm Line length: About 1350mm Soldering: iron holder size: 135 72 83mm Package Size: 207 121 95mm Input voltage: AC100 240V The output voltage: DC 15V Frequency: 50~60HZ Warming time: 2S Output peak power: 110W Inductive sleep: Yes Display method: LED temperature display
