Himatrix F3 Dio 8/8 01 Manual

Supplier: 1) plastic injection molded parts 2) mould design and development 3) automotive plastic parts 4) auto electrical parts 5) industrial/automotive battery parts 6) plastic household products 7) gear moulding 8) over moulding 9) insert moulding
Buyer: 1) copper plated/tin plated terminals for auto electrical parts.

Supplier: 1. semiconductor / display material, part, equipment 2. electrical/electronic material, part, equipment 3. medical / biomaterial, equipment 4. machine metal part 5. chemical materials 6. power parts 7. car parts 8. cosmetic 9. consumer goods
Services: Consulting and advisory services: offering expertise and support for businesses engaging in international trade, such as compliance with trade regulations, market entry strategies, and risk management.
Buyer: Material, parts and equipment

Supplier: 1 lv and mv power cables , telecommunication cables , lsfh ,solar ,instrument and special cables. 2 copper rod 8 mm and copper wire from 1.60 to 3 3 pvc compounds

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

- Solar Lawn lamps 5 W / 7 W; - Housing: Aluminum Alloy; - 5 V / 5 W / 8 W / solar panel ; - Ternary Lithium Battery 4.2 V / 4.4 Ah; - LED chip SMD 20 pcs / 30 pcs; - Light Size: OD 205 mm, H 170~340 mm, Flange: ID 110 mm; - Control Mode: Light Control; - charging time 6 to 8 hours, Lighting time 12 hours;

- Solar flood lamp 40W/60W/120W/200W (Tetrad ); - Housing: Die Casting Aluminum; - 6V / 15W / 18W / 25W / 30W solar panel with 5M cable; - LiFePO4 Battery 3.2V / 10Ah / 13Ah / 30Ah / 35Ah; - LED chip 5730 SMD 180pcs / 216pcs / 396pcs / 660pcs; - Light-dependent control / Time control with remote; - charging time 6 to 8 hours, Lighting time 12 hours; - Battery indicator and intelligent timing, Color box/set.