Normally Closed Solenoid Gs021600V + Ccp230M

Plunger Type Pumps, Hydraulically Actuated Diaphragm Type Pumps, Mechanically Actuated Diaphragm Type Pumps, Solenoid, Operated Diaphragm Dosing Pumps, Complete Skid Mounted Dosing Systems, Chemical Process Pumps, Seal free Magnetic Drive Pumps, Progressive Pumps, Y Type Strainers, Pulsation dampners, etc.

SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".

6-35kv medium vollage power cable selection with cross-linked polyethylene insulation and plastic Sheath material, insulation layer USES the three co-extrusion technology, full automatic Change control. Such products, aging resistance, corrosion resistance, environmental stress not only electricity Gas properties and good mechanical properties, and has a simple structure and outer diameter Small, light weight, easy to use and elaborate divide not restricted, Public places such as crowed, place closed space.

The cable design conforms to the requirements of national standard GB/T12706-2008 and IEC60502 recommended by international Electrotechnical Commission. The normal operating temperature of the conductor of polyvinyl and XLPE insulated cable is 70â?? and 90â?? ,Xlpe cable not only has excellent electrical performance, high working temperature, large transmission capacity, but also has the advantages of simple structure, small outer diameter, light weight, easy installation and use, and unrestricted laying drop. It is widely used in industrial and mining enterprises and urban power grid.

Supplier: Centrifugal monobloc pump sets, end suction centrifugal pumps, vertical in line pumps, transformer oil pumps, close coupled centrifugal pumps, centrifugal pumps, a.c induction motors, solar pv surface pumps.
Services: Manufacturer, supplier & exporter

Design Features: Horizontal, Centrifugal, Monobloc (pump & motor have been combined to form a single unit) type pump fitted with single stage closed Impeller in Volute Casing having axial end suction and vertical centerline delivery. No fear of motor burning due to wide operating voltage range and Non-overloading power characteristics at any operating point. Advantage of mounting space saving due to elimination of base plate, coupling and coupling guard. Custom-built Design: Pumps with variable supply voltage / frequency and different material of construction can be offered on request.

AIR Circuit Breaker Spares And Parts Str 38 S , Motor Spring Charges , Coil , Shunt Closing Trip Etc