Water Level Sensor

The Separated Liquid Flow Sensor A1MF can be used to detect high and low water levels, etc., and give a signal when the water level reaches a certain position. The Non contact Infrared Level Sensor is a device used to sense the level of liquid in a tank. There is a board in the plastic housing. When the liquid level rises, it drives the prism, level switch will output low voltage signal. When the liquid level falls, infrared level control will output high voltage signal. The photoelectric liquid level switch uses the principle of optical reflection to measure, the performance of level sensor will be affected when it is exposed to direct sunlight or other infrared interference. Adjust the mounting angle or use a hood to avoid it. The photoelectric liquid level switch has high precision, low price, high reliability and wide application environment, it is less affected by strong acid, alkali and viscosity.

Item Type: Flow Float Switch Sensor ; Item No: CFS-1025P Color: white; Cable Length: 350mm / 13.78inch; Switch Body Size: OD18 x 8mm; Thread Dia(Approx) : M8*1.25; Max Contact Rating: 10W; Float Body Material: PP Float Ball Material: PP Working Voltage: AC 110V-220V; Working Temperature: -10â??~85â?? Max Temperature: 85 Working Pressure: 0.4 Mpa; Max Pressure: 0.4Mpa; Max Switching Current: 0.5A; Max Breakdown Voltage : 220VDC; Max Carry Current : 1.0A; Max Contact Resistance: 100m Ohm; Max Carry Current : 1.0A;

This float switch is a device used to sense the liquid level of a tank, and may activate a pump, an alarm, or any other device AC 110V to 220V circuit can be used, electrical lifespan: 1 million times. It widely apply to the field of Tanks, aquariums, water dispenser, drainage system, drinking fountains, industrial equipment, agricultural equipment, household appliances, chemical liquid level control system, bathroom equipment vending machines, etc. Send me message for further support if you need customized product, we could offer you different material &different size customized product service PRODUCT SPECIFICATION: Item Name: Water level sensor float switch Color: white Cable Length: 350mm / 13.78â??â?? Switch Body Size: OD19 x 16.6mm Thread Dia (Approx): M8*1.25 Max Contact Rating: 10W Float Body Material: PP Float Ball Material: PP Working Voltage: AC 110V-220V Working Temperature: -10â??~+85â?? Max Temperature: 85â?? Working Pressure: 0.4Mpa Max Pressure: 0.4Mpa Max Switching Current: 0.5A Max Breakdown Voltage: 220VDC Max Carry Current: 1.0A Max Contact Resistance: 100mOhm Max Carry Current: 1.0A

HPT612-W is full sealed submersible level sensor. It is made by building in high stable and reliable piezo-resistive silicon pressure sensor and high accurate circuit board into the stainless steel housing. Integrated construction and standard signal provide the user easy and convenient application in the local working place. The special cable connects with housing, can be immerged into the media for a long time. HPT612-W level sensor has smart structure, high accuracy and good stability; it can be used for water or liquid measure and control of medicine, metallurgy, electricity, mine, city water supply and drainage and hydrology, etc. HPT612-W level transmitters is based on Zigbee wireless protocol and max transfer distance up to 400 meters, if add a wireless signal router, distance up to 800 meters. Characters: Accuracy: �±0.25%F.S. Wide working temperature scope Double supply by battery&DC power User-defined data transfer interval time With English level monitor PC software Highly-efficient lighting absorption and strong RFI & EMI resistance Remote signal transfer by Zigbee. 1.5 times range standard overload. 3 times range burst pressure CE approving Applications: well depth measurement and control water tank level measurement river level measurement and control wireless level monitor system Industrial course testing and control Building water supply systems Oil and Fuel Tank level measuring Automatic detection system Saving water to irrigate Liquid pressure and level measurement And so on

Non contact ultrasonic level switch is a kind of non-contact, high reliability, high cost performance, easy installation and maintenance of material level measuring instrument.It doesn't have to contact medium can meet the requirements of most of the material level measurement.Firing pulse and receives the pulse interval and the antenna to the surface of the measured medium is proportional to the distance, to calculate the distance on the surface of the antenna to the measured medium. Ultrasonic Level Sensor, As shown in Picture below, the ultrasonic sensor Tx transmits ultrasonic waves reflected after encountering an obstacle received by the ultrasonic sensor Rx calculates the distance d of the obstacle according to Time-Of-Flight (TOF):d = (C x t)/2

FS-IR02B series Water Liquid Single Point Level Sensor, the theory is infrared, it can totally replace traditional float level switch, it controls the level though output high or low voltage. When the detected level is in air, due to reflect of the prism,most of light will enter receiver LED, optical level sensor will output high voltage. When the detected level is in water, due to refraction of the liquid, just less of light enter receiver LED, optical level sensor will output low voltage.

The FS-IR2003D is a single point liquid level switch that can operate in high pressure, high temperature, and aggressive environments due to its stainless steel and glass construction. This level switch offers industrial supply voltages and outputs that can directly drive loads. This model has a wide operating voltage, which is from 5VDC to 24VDC. The output ways have two types, NPN and PNP. The sensor can detect the presence or absence of almost any liquid, and can be configured to output a high or low signal in either a wet or dry state. The microcontroller based Stainless Glass Range liquid level switches are solid state, incorporating an infra-red LED and phototransistor which are optically coupled by the tip when the sensor is in air. When the sensing tip is immersed in liquid, the infrared light escapes making the output change state. The sensor can detect the presence or absence of almost any liquid type; oil or water based. It is insensitive to ambient light and is not affected by foam when in air or by small bubbles when in liquid.

The reliability of liquid tank level sensor FS-IR2016D is high. It is not affected by liquid corrosiveness, pressure, magnetism, temperature, etc., it is less affected by external factors and has strong stability. EPT sensor is a manufacturer of liquid level sensors with 16 years of experience. We can provide corresponding solutions for all kinds of electrical equipment and other scenarios that require liquid level detection. If your steam microwave oven needs water level control, please contact us, we can provide you with food grade, hygienic, high precision, high reliability liquid level sensor to solve problems such as scale and water wall hanging. FS-IR2016D optical water level sensor has no mechanical moving components and with high reliability. This hot selling product is small in size and low in cost. Its advantage is high liquid level control precision. And it can be installed from any direction. Its waterproofing standard is IP68. The sensor itself also satisfies RoHS requirements.

Horizontal level sensor are side-mounted through a hermetically sealed hole on the side of a tank. With a doughnut-shaped floats rising and falling with the level of the liquid around stems, actuating reed switches inside the stems. Wires then send an electric signal to the outside of the tank , making these components essential for accurate monitoring. Features of horizontal water level sensor Compact size and easy to install. No power consumed in standby status. Design to work in harsh environment Size, cable length, connect and float are customizable There are many position sensor manufacturers, but we are one of the best choices for you.