ZP vertical centrifugal slurry pump, also known as a submerged slurry pump, submerged in liquid, with a vertical cantilevered single pump casing structure and a semi-open impeller. Without any shaft seal and shaft seal water, it can work even in the case of insufficient suction volume. The wet parts are made of high chrome alloy wear-resistant metal, Suitable for conveying dense slurries with large particles and high abrasiveness
Spare Parts for 65QV-SP, 100RV-SP, 150SV-SP Vertical Slurry Pumps. Mainly SP Metal Lined Vertical Sump Pump Parts: Impeller - Double suction impellers (top and bottom entry) induce low axial bearing loads and have heavy deep vanes for maximum wear resistance and for handling large solids. Wear resistant alloys, polyurethane and moulded elastomer impellers are interchangeable. The impeller is adjusted axially within the casting during assembly by external shims under the bearing housing feet. No further adjustment is necessary. Bearing Assembly - The bearings, shaft and housing are generously proportioned to avoid problems associated with the operation of cantilevered shafts in the first critical speed zones. The assembly is grease lubricated and sealed by labyrinths; the upper is grease purged and the lower protected by a special flinger. The upper or drive end bearing is a parallel roller type whilst the lower bearing is a double taper roller with preset end float. This high performance bearing arrangement and robust shaft eliminates the need for a lower submerged bearing. Column Assembly - Completely fabricated from mild steel. G refers to submerged depth 1200mm; J refers to submerged depth 1500mm; L refers to submerged depth 1800mm; M refers to submerged depth 2000mm; Q refers to submerged depth 2400mm; Casing - Has a simple bolt-on attachment to the base of the column. It is manufactured from a wear resistant alloy for the SP and from moulded elastomer for the SPR. Upper Strainer - Snap in elastomer strainers fit in column openings to prevent overly large particles and unwanted refuse from entering casing of the pump. Lower Strainer - Bolt-on cast strainers on the metal pump and molded snap-on elastomer strainers on the rubber pumps protect the pump from oversize particles. Discharge Pipe - Metal for SP, elastomer covered for SPR. All wetted metal parts are completely rust protected. Fully Cantilevered - Eliminates submerged bearings, packing, lip seals, and mechanical seals that other vertical slurry pumps typically require. Agitation - An external agitator spray connection arrangement can be fitted to the pump as an option. Alternatively, a mechanical agitator is fitted to an extended shaft protruding from the impeller eye. Materials - Pumps can be manufactured in abrasive and corrosive resistant materials.
SPR65092R55 Casing Spares on 65QV-SPR Vertical Cantilever Sump Pumps. Tobeea Vertical Spindle Pumps are available in a wide range of popular sizes to suit most pumping applications: Minerals processing Coal preparation Chemical processing Effluent handlin Abrasive and/or corrosive slurries High density slurries Sand and gravel and almost every other tank, pit or hole-in-theground slurry handling situation.
Product introduction: CK1 CKX is a single-stage single suction cantilever type centrifugal pump, the excellent hydraulic model and structure ensures that the user can effectively reduce the running cost of the pump in various occasions. Product features: The mechanism is simple, compact, small size, light weight, low power consumption, convenient repair using let characteristics. Technical parameters: Lift4.7-100m Flow4.5-380m/h Field of application: Apply to the transport of water and physical, chemical properties similar to liquid water, used in factories, mines, power plants, city water supply and drainage, air conditioning system, fire protection system, farmland irrigation and drainage.
1.5 1B-TH Slurry Pump is end-suction, split-case, centrifugal slurry pumps have set the world standard for heavy duty abrasive pumping applications. With large shaft diameters, heavy duty bearing assemblies and robust slurry pumping capacity, Application customization comes standard with this line by applying a wide variety of metallic and elastomeric parts options, an assortment of seal arrangements, and a standard impeller adjustment mechanism incorporated into every base assembly. Slurry Pump Design Features Slurry Pump wet parts are made of wear-resistant high chromium alloy. Slurry Pump bearing assembly use cylindrical structure, adjusting the space between impeller and front liner easily. They can be removed completely when being repaired. Bearing assembly use grease lubrication. International famous bearing The shaft seal could use the packing seal, expeller seal and mechanical seal for all slurry pump. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications at its working site. There are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. Wide performance, good NPSH and high efficiency. The slurry pump can be installed in multistage series to meet the delivery for long distance.
The versatile, fully lined Xinte® ZTNM series slurry pump offers a wide range of seal and rubber (wear-resistant metal) liner configurations allowing the pump to be tailored to the customer¡¯s specific application. Range of Applications of ZTNM Slurry Pump ZTNM series horizontal and cantilever centrifugal slurry pumps are used widely throughout the beneficiation section of the mining industry. ZTNM slurry pumps are also widely used for the disposal of ash from power plants the manufacture of fertilizers, and the long distance transportation of coal and minerals. Increased global focus on the environment and energy consumption will certainly generate much wider uses for slurry pumping in years to come. Design Features 1, Bearing assembly ¨C A large diameter shaft with short overhang minimizes deflection and contributes to long bearing life. 2,Liners ¨C Easily replaceable liners are bolted, not glued, to the casing for positive attachment and ease of maintenance. Hard metal liners are completely interchangeable with pressure molded elastomers. Sandwich Plate Carton.
Discharge diameters - 40mm to 250mm Flow rate to 1267m3/h Head range to 40m As customers'requests
The L series slurry pumps are cantilevered, horizontal, centrifugal, slurry pumps. They are suitable for delivering less abrasive, low dense slurry in the metallurgical, mining, coal and construction material industry. The shaft seal is adopted both gland seal and centrifugal seal. The L series slurry pumps have a high rate of revolution and small volume saving floor area. The frame plates have changeable, wear-resistant metal liners or rubber liners upon request and the impellers are made of wear-resistant metal or rubber. The discharge branch can be oriented to any of the eight different positions for installation and application upon request.
Vertical slurry pumps are no submerged bearings or seals cantilevered pumps, which ideal for a variety of submerged suction pumping applications. These pumps operate well in a variety of sump conditions, and can also be readily applied on floating dewatering or other floating pump platforms.
