TE Terminal MQS, Automotive Terminals, Receptacle, Mating Tab Width .63 mm [.025 in], Tab Thickness .025 in [.63 mm], 24- 22 AWG Wire Siz
PE coil pipes and tubes for water and wire cable conduit PL231 The PE coil pipes and tubes can be used: water pipe 4 â?? 6 â?? 1-inch black coil with pressure 1.6mpa, OD 20-75mm, WT 2.3-6.8mm pe conduit cable embedded wire cable and optical cable, OD 20-200mm, WT 1.8-3.5mm weak current protection tube and communication tube, OD 20-200mm, WT 1.8-3.5mm We use new 100% pure raw PE material WHY NEW MATERIAL HDPE PIPES? 1. Health performance PE pipe processing without adding heavy metal salt stabilizer, no scaling layer, and no bacteria. 2. Corrosion resistance It can resist various chemical media erosion, with no electrochemical corrosion. 3. Service life Under rated temperature and pressure conditions, PE pipes can be used for more than 50 years. 4. Impact resistance PE pipe toughness, high impact strength, heavy objects directly pressed through the pipeline will not break. 5. Connection performance The strength of the hot melt or electric melt interface of the polyethylene HDPE pipe is higher than that of the pipe body, and the joint will not be broken due to soil movement or live load. 6. Construction performance It has a lightweight pipe weight, a simple welding process, convenient construction, and a low overall project cost.
Part No 2109
TE Terminal Generation Y Connector System, Automotive Terminals, Receptacle, Mating Tab Width .64 mm [.025 in], Tab Thickness .025 in [.64 mm]
Automotive Terminals, Tab, Mating Tab Width .059 in [1.5 mm], Tab Thickness .031 in [.8 mm], 22 - 20 AWG Wire Size, AMP Superseal 1.5mm Series
Supplier: 1) plastic injection molded parts
2) mould design and development
3) automotive plastic parts
4) auto electrical parts
5) industrial/automotive battery parts
6) plastic household products
7) gear moulding
8) over moulding
9) insert moulding
Buyer: 1) copper plated/tin plated terminals for auto electrical parts.
Product Overview The ignition point of a fire inside the electric panel is mostly the part where the terminal block is fastened, so in order for initial fire extinguishing, the solution should be closely installed to the part where the terminal block is fastened. In the case of a small electric panel, a complete initial fire extinguishing is expected for fires occurring inside the electric panel by attaching the SFEX Pad to the top surface of the electric panel. Product Feature It has an excellent performance in the initial fire suppression as it can be installed near the ignition point as a flexible rope type. It uses a stand-alone method based on polymer chemistry so that it does not cause malfunctions and maintenance costs. The thermo-responsive Granule composed of KNO3 and subsidiary catalysts It does not affect the peripherals after the fire goes out. Function of SFEX Granule = fire extinguishing agent storage tank + temperature sensor + nozzle function Fire extinguishing method : Suffocation + subsidiary catalyst Example of Installation 1 : SFEX Line - If ducts exist Installing the SFEX Line horizontally or vertically in the ducts closest to the expected ignition points It can be installed without damaging the panel Example of Installation 2 : SFEX Line - If ducts do not exist Installing the SFEX Line horizontally or vertically, close to the expected ignition points of the Electric panel Example of Installation 2 : SFEX Pad - Small Electric Panel Simply attach it to the top inside the Electric panel.
System voltage 415 V +/- 10%, 3 Phase, 4 wire AC 2. Frequency 50 Hz +/- 3% 3. Fault level Shall be designed for fault level of 50 KA for 1 sec 4. Grounding Solidly grounded neutral system 5. Insulation level a) Power circuit b) Control circuit 2.5 KV / 1 minute 1.5 KV / 1 minute 6. Main bus bars Shall be designed to carry continuous current rating of 1.2 times of incomer ACB unitâ??s continuous current rating and STC of 50 kA for 1 sec. Temperature rise, short circuit design shall be as per IS 8623. Max. Current density for the material of bus bar shall be as follows: Copper: 1.6 Amp/Sq.mm Aluminum: 0.8 Amp/Sq.mm (For Sl. No. 12 PCC)
If you have the following product requirements, you can contact me to inquire,thanks. 1. Plug-in series, phoenix socket, pitch 3.5mm, 3.81, 5.0mm, 5.08mm, 7.62mm, etc pluggable terminal block. 2. Double-layer press type screw-free series 5.0mm spring terminal block 3. all kinds of barrier terminal blocks Whatsapp/Skype: +8615813394039 Dongguan AOSI Electronics Co.,Ltd is the collection development, production, sales in one of the specialized terminals, terminal, terminal, connector, connectors manufacturers, and has a number of high-quality management team and technical elite, through nearly ten years of careful management, products through the UL, VDE, CB, CQC, ROHS and other certification, the factory has passed ISO9001 : 2008 quality system certification. The main products are: CA series shrapnel type wiring terminal, CT series lifting type wiring terminal, CP series slide-in terminals, CS series screw free press buckle type connection terminal, CK series, CZ series fence type wiring terminal through type wiring terminal, a variety of single double pin and IC socket. Standing specifications have 2.54, 3.50, 3.81, 3.96, 5, 5.08, 6.35, 7.50, 7.62, 8.255, 9.525, 10, 10.16, 11, 13.00mm.
Certification:CE SGS UL Material: Pin header,Brass,Tin plated Wire guard: Stainless steel(SUS301) Plastic: PA66 UL94V-0 Electrical Standard: UL,IEC Rated voltage: 300V 250V Rated current: 10A 15A Wire range: 26-16AWG 1.5 mm2 Contact resistance: 20m Insulation resistance: 500M/DC500V Withstand Voltage: AC2000V/1Min Mechanical Temperature range: -40C~+105C MAX Soldering: +250C 5 Strip length: 8-9mm Size Pitch: 5.0mm(.197") Poles: 1P-XXP If you have the following product requirements, you can contact me to inquire,thanks. 1. Plug-in series, phoenix socket, pitch 3.5mm, 3.81, 5.0mm, 5.08mm, 7.62mm, etc pluggable terminal block. 2. Double-layer press type screw-free series 5.0mm spring terminal block 3. all kinds of barrier terminal blocks