Handpiece Interpulse With Tip

Handpiece Interpulse With Tip, Tube UOM: 6/CS Product Number: 0210-114-000 Manufacturer: Stryker

Traditional fiber optic handpiece cannot work without wire. Now our revolutionary new product E-Generator Fiber Optic Handpiece brings light without wire. This Handpiece has an internal Air-Driven Generator, which supplies fiber optic to light the tip of the handpiece. NEW SY E-Generator Fiber Optic Handpiece high performance 25,000 LUX. It also offers triple water spray. Improving visibility and cooling where you need it. 1. Super torque, standard head, mini head 2. 2 Hole/ 4 holes 3. Triple water spray 4. Fibre optic handpice with Air-driven generator inside; 5. Push button 6. Ceramic bearing 7. Noise Level: less than 70dB 8. Net weight: 88g 9. Torque Head Height 12.55 mm 10. Torque Head Diameter 14.4 mm 11. Air Pressure: 250-300Kpa 12. Rotation Speed: 310,000-350,000 RPM. Please contact us through SYdentistry website directly; we will get back to you within 24 hours.

SY E-Generator LED Dental handpiece brings light to dental offices that have been using handpieces those do not have the light on the tip. It has an internal power motor that is air-driven, which supplies LED lighting to the tip of the handpiece, so dental professionals can view the operation area without outside light. In fact this SY lighting system is even more focused and bright than most fiber optic systems. The pricing, as we are manufacture, sells even lower than most other regular high speed handpieces. It also weighs less than most others. Some other features are below for your reference. 1. Self-sufficient power system instead of external light source. Self-illuminated, natural light 2. Operating air pressure: 0.25-0.3Mpa (0.3MPa preferred) 3. Air consumption: 55L/min 4. Speed of generator: 25,000-30,000 R.P.M 5. 420,000 r.p.m for standard head 6. Ceramic Bearings: Quieter and longer life 7. Push button 8. Triple water spray 9. Sterilization by autoclave at (135) Centigrade 10. Unenclosed Cartridge 11. Noise level: Less than 68 dB 12. Chucking power: 20-45N 13. Net weight: 88g 14. Ergo Grip: Secure Grip for your confidence 15. ISO 7785-1 16. CE Mark 0197 17. One year guarantee (half year for bearings).

Features: 1. Steady power, high efficiency and negligible heat generation. 2. Digitally controlled, automatic frequency tracking 3. High strength alloy scaling tip 4. Ergonomic design 5. High quality and durable cable. 6. Titanium alloy axis 7. Full spectrum power range 8. Exquisite craft work, small and light 9. Detachable Handpiece 10. Can be autoclaved at 135 centigrade and 0.22MPa. Technical information: 1. Adapter input: 110V~230V ~ 50/60Hz 2. Main unit input: 24V ~ 50/60Hz 3. Input power: lower than 40VA 4. Main unit fuse: 250V/T 1AL 5. Output power: 3W to 20W 6. Primary tip vibration excursion: lower than100um 7. Tip vibration frequency: 28kHz 8. Half-excursion force: lower than 2N 11. Water pressure: 0.01MPa~0.5MPa(0.1bar to 5bar) 12. Gross Weight: 2.2Kgs 13. Net weight: 1.85Kgs

Tungsten Carbide Dental Burs Description Tungsten carbide dental burs are manufactured from a single piece of tungsten carbide (TC) or from a TC tip brazed onto a surgical steel stem. The range includes patterns designed to meet the needs of all surgery and laboratory applications. Tungsten Carbide Dental Burs Applications Tungsten carbide dental burs can be used to cut or polish a wide variety of materials encountered in dentistry. These include tooth material such as enamel, dentine and bone, dental materials such as amalgam, composite, glass-ionomer cements, polymer and ceramic veneers and precious and not-precious alloys. The bur pattern will be selected to cut a specific material in a specific application and the following table gives guidance on selection. Safety in Tungsten Carbide Dental Burs Use Eye protection must be worn to protect against ejected particles. Surgical mask must be worn to avoid inhalation of aerosol or dust generated. Inspect the bur for broken flutes before each use and discard defective burs. Ensure that the bur is fully seated and gripped in the handpiece collet. Maintain handpieces in good working order and correctly lubricated. Do not exceed the maximum speeds tabulated above. Move the bur continuously when in use to avoid localized heating. Clean and sterilize the burs in accordance with the directions below before first use an before each reuse. These instructions are applicable to the processing of tungsten carbide, diamond and steel dental rotary instruments before first use and each reuse. Dental rotary instruments are supplied mechanically clean but are not sterile. They should therefore be sterilized before first use. Steel burs are single use devices and the instructions therefore only apply to processing before first use. Used burs should be considered as contaminated and appropriate handling precautions should be taken during reprocessing. Gloves, eye protection and a mask should be worn. Other measures may be required if there are specific infection or cross-contamination risks from the patient. With the exception of steel burs, which are single use devices, reprocessing will have little effect on dental burs. The end of life is determined by wear and damage in use and the burs should be inspected for defects during the preliminary cleaning process. Unless there is specific infection or cross-contamination risks, there are no special requirements for containment. The burs can be transported wet or dry and should be protected from damage to the cutting edges. If transported wet there is an increased chance of staining or corrosion. Prolonged storage in disinfectant solutions may result in corrosion and should be avoided.

Whitening handpiece for teeth bleaching consist of whitening handpiece and bare fiber, contoured to treat an entire quadrant of teeth consistently and comfortably. Specifications Handpiece length: 140mm Whitening tip width: 45mm Whitening tip thickness: 7mm Tip radial: R50 Bare fiber Core: 200um, 400um NA: 0.22 Length: 2m Connector: standard SMA905 or FC Aesthetic procedures Bleaching 1.5-3W Depigmentation 2-3.5W Gummy smile correction 2W Aphthae and herpes 1.5-2W Crown lengthening 1.5W

The dental laser handpiece 670 can be matched with the disposable tip, whitening tip, bio-stimulation tip and TMJ therapy tip. Besides, our handpiece can match with the mainstream laser machine all over the world. Any oral laser machine of pluggable fiber, SMA905 or FC connector are all compatible, including Biolase Laser, Denlase Laser, Doctor Smile Simpler, AMD Laser.

Alma Soprano XLi with SHR Diode & NIR Handpieces; Excellent Cosmetic and Operating Condition, Single Owner, Full Maintenance Service, Calibration, and Replacement of Flow Switch Performed on 08/30/2019, Record Available Upon Request; Original SHR Total Pulse Count = 10,241,483; NIR Total Pulse Count =2,545,712 ; Includes: (1) 810 Diode Handpiece with Sapphire Dual Chill Tip and 12Ã??10 mm Spot Size, (1) NIR Skin Tightening Handpiece, (2) Keys, (1) Footswitch, (1) Operator Manual, (1) Consult Book, (1) Water Refill Kit, (1) Warning Sign, and 120 Day Warranty

SPECIFICATION Tip 18 x 15.2 mm (WxH) Overall handpiece length 266 mm Weight 276g Imaging technology 3D-in-motion video technology Color 3D full color streaming capture Connectivity USB 3.0 Scanning FOV 14 x 13 mm