Wellcoat Red/Grey oxide primer is a solvent based anticorrosive primer formulated with Alkyd resin, Red oxide pigment & other rust inhibitive ingredients. This is economic anticorrosive primer widely used in metal fabrication industry for use over
ferrous substrates & can be over coated with Wellcoat Maxigloss enamel. The product can also be used in Auto refinish system as metal primer followed by Nitrocellulose surfacer & topcoat.
An anticorrosive primer based on high molecular, two pack, epoxy-polyamide resin system and anticorrosive pigment excellent drying, adhesion and abrasion resistance properties.
An anticorrosive primer/ intermediate topcoat based on high molecular, two pack, epoxy-polyamide resin system and anticorrosive pigment excellent drying, adhesion and abrasion resistance properties.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Features: 1.Strong adhesion,high compactness and super anti-rust 2. Excellent weather resistance to harsh summer and winter, acid and alkali resistance, high solid content 3. Superior flexibility of paint film 4.Easy application Application site: 1.Bridge, steel structure, iron tower,vehicle and steel equipment 2.Wooden products
Water Based Coatings - Primers, Gloss & High Scuff - High Gloss/High Slip - Duct Gloss & Matt - Specialty Coatings - Soft Feel / Satin / Neutral / Super Matt
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
We are an intermediate associate with leading paint manufacturers based in Dubai Specializing in *Architectural coatings *Wood coating *Automotive Refinish *Protective coating *Thinners We Do branding, Marketing and logistics support to your door step
"Acrylic co-polymer-based primer cum sealer containing containing some aggregates , alkali resisting pigments / extenders & low particle size emulsion for better penetration on to the surface thus most effectively sealing the surface & improving adhesion of the subsequent coats. The product is compatible with similar products of any origin"
Water based Alkyd resins for industrial coatings Alkyd resins represent, both historically and commercially, the class of chemical compounds used in the field of paints and stains. Their chemical structure is a continuous and waterproof film which can protect surfaces from multiple strenuous agents conducting an anti-corrosive. The commercial paints based on these resins, the molecules of the structure, in particular, create strong structural interactions involving the formation of films able to cover any type of surface by protecting against aging, weather and wear. the paints made from alkyd resins have been among the first to be used in the construction industry, in particular in the production of exterior paints and enamels, and in the production of products for the treatment of surfaces exposed to particularly arduous conditions, for example various ferrous metal substrates such as structural steel, railings, equipment and machinery. We offers alkyd resins that have achieved high functionality through modification with other resins such as acrylics, urethanes, epoxies. Features: Good storage stability, no ease to hydrolyze; Environment friendly product, VOC of less than 7%; Fast dry, and excellent gloss; unnecessary to add drier during paint preparation; Excellent shear stability, and can directly use for pigment paste grinding; Excellent anti-corrosivity, and good initial water resistance; The finished product paint has good versatility and good in-can appearance, and can replace oil based alkyd anti-rust paint, alkyd ready mixed paint, alkydenamel, etc Waterborne Acryle Resin Product No. WL-310 Acryle modified akyd dispersion Solids content: 42±2 Viscosity(25,mPa·s): 2000 Air dry: Oxidation Cross-linking Property:Low VOC; High gloss; Excellent corrosion resistance. Application:Waterborne alkyd enamel ready mixed paint and anti-rust paint PS:(1) The Viscosity withï¼?is measured in the case of the resin diluted by equivalent amount of propylene glycol methyl ether.
