1. Material: Polypropylene (PP-R) & Blue
2. Collector pipe size: 20*2.0 mm
3. Capillary tube size: 4.3*0.8 mm
4. Spacing of Capillary tubes: 10mm, 20mm, 40mm,
5. Width: 1000mm
6. Connection method: Connect mats to another and to the water circuit by means of thermal welding.
7. Test pressure in production: 20 bar
8. Recommended operating pressure: 4 bar
9. Max allow heating water temp: +60
10. Optimal input temp. For heating: +28~32
11. Optimal input temp. For cooling: +16~18
12. Type of delivery: The mats are supplied rolled-up, packed in cartons
It's an energy-efficient, low-temperature heating and high-temperature cooling system.
It is made of Polypropylene. It consists of the multitude, parallel plastic tubes with diameter of only 4.3mm and two collection pipes.
The mats can be connected to different heat energy carrier (heat pump, gas boiler, central heating, solar energy) that is circulating at an efficient temperature.
Model Number: Portable Air Conditioner ((WT-F26 gray) Power Type: DC Use: Room Condition: New After-sales Service Provided: None Warranty:1 year Type: PORTABLE Certification:CB, ce Cooling/Heating:Cooling Only Application:Car, Commercial, Garage, Hotel, Household, Outdoor, RV Power Source:Electric, usb Remote Control: Yes App-Controlled: Yes
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Flexible Duct & Accessories
Duct Fabrication
Grill & Diffuser
A/C Units
Supplier: Air conditioner spare parts , compressors , gases and motors.
Buyer: Air conditioner spare parts , compressors , gases and motors.
i.About The Product The device is designed based on the Volkswagen Passat B5 automatic air conditioner system to holistically demonstrate the structure and operation of the system. The device applies to theoretical teaching and maintenance training of the automatic air conditioner system in secondary and senior vocational skill schools, normal education and training institutions. ii.Features 1.A real and operable automatic air conditioner system is used to illustrate the structure and operation of the system. 2.The compressor is driven by a three-phase motor. A control panel can be operated to demonstrate operation and operating principle of the automatic air conditioner system. Heat generated by the water heater. A control panel can be operated to demonstrate operation and operating principle of the auto manual air conditioner system. 3.The training bench is made of advanced aluminum-plastic plate with characteristics of not less than 4mm thick, corrosion resistance, impact resistance, pollution resistance, fireproof, and moistureproof. Its surface are processed by special craft and spraying primer. Never fade color circuit diagram and working principal diagram are painted on the board whose surface coating with varnish. The trainees can learn and analyze the working principle of the control system by referencing the diagram and the real object. 4.The training bench is installed with detection terminals to detect electric signals, for example, resistance, voltage, current, and frequency, of circuit components of the air conditioner system. 5.The training bench is installed with pressure gauges and thermometers, which display real-time pressure and temperature at the inlet and outlet of the air conditioner system. 6.The training bench supports practice of filling refrigerant and detecting leakage. 7.The training bench's base frame is made in steel and the surface is paint-coated. Self-retention wheels are installed to ensure that the bench is flexible, reliable and endurable. 8.Equipped with intelligent fault setting and appraisal system, include fault setting, troubleshooting and assessment functions etc. iii. Basic Parameter 1.Size: 1000mm � 1000mm � 1800mm (length x width x height) 2.Driving power supply: three-phase four-wire (three-phase five-wire 380 ± 10% V 50 Hz) 3.External power supply: A.C. 220V ± 10% 50Hz 4.Operating voltage: 12V DC 5.Refrigerant: R134a 6.Operating temperature: -40? to +50? 7.High pressure gauge: 0 ? 3.5 Mpa 8.Low pressure gauge: 0 ? 1.5 Mpa 9.Three-phase asynchronous motor ? Model: YT 100L1-4 ? Voltage: A.C. 220V/380V ? Power: 2.2 KW ? Rotation speed: 1420 r/mi
"Ultrasonic heating and cooling energy meters to measure flow and energy in hydronic heating or refrigerant circuits. Available as heat, cooling energy, or combined heat/cooling energy meters Separate acquisition of heating or cooling energy by the combined heat/cooling energy meters, with automatic changeover Non-wearing due to non-moving parts Approved in accordance with EN 1434 and MID accuracy class 2 Any mounting position (horizontal or vertical), in return Measuring range of flow 1:100 as per EN 1434, 1:1,000 total range Choice of communication modules and power supplies Upstream or downstream setting paths are not required Optical interface as per EN 62056-21 Self-diagnostics"
