Widely used in condensate polishing as precoatmedias. Powdered resins are widely used in condensate polishing as precoat medias. They are also used in the manufacture of membranes and other unique applications that require powders ground from resins. XResins powdered resins can be ground to very precise particle size requirements.
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
Powdered resins are widely used in condensate polishing as precoat medias. They are also used in the manufacture of membranes and other unique applications that require powders ground from resins. XResins powdered resins can be ground to very precise particle size requirements.
METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
1.Product name : melamine resin powder 2.Color : white , black , ivory , green , blue , gree , red and more customized as requirement 3.OEM service : molding temperature , curing time , color ,flowability , shiping marks 4.Application :abrasive tools ,diamond polishing pad 5.Other products :melamine resin powder 330 and 331 6.Packing 10kgs , 20kgs, 25kgs 7.Loading quantity : 20mt in 1*20 feet container
Reaches European Standard E0 Class. According to different Production Process of artificial panel, it could be used in different fields. Technical Specifications: Appearance: White or yellowish powder Granularity: over 95% pass 100 mesh Free formaldehyde: í_0.04% PH: 8.0-9.0 Water Content: í_2% Storage: Stored in cool place with sealed package at room temperature Package: Two-ply bag with an inner plastic bag and an outer fabric bag 25kg / bag
1. Physical property: White powder of high-molecular compound which becomes by the vinyl chloride monomer polymerization, it is with high whiteness, good workability and the resin pellet is loose & symmetrical. 2. Manufacturing process: Adopt suspension polymerization technology & equipment which self-develop and home-made. Quality standard Standard of the peopleí»s republic of China GB/T5761-2006 3. Application: General SG5 is suitable for the production tubing, the plate, the windows and doors, the different molding, the thin film, the hot contraction membrane, the artifical leather and so on.. SG3 is suitable in producing the electric insulation material, the cable sheath bond, the soft profile, kinds of thin film, plastic slipper, the automobile parts, the electric appliance and so on. SG7 is used in producing the transparent hard piece, the fitting, various packing container, the bottle material, the record disc, the smoke membrane, the gold card and so on. 4. Packing: Packed in kraft paper and polypropylene plastic woven compound bag , each bag of net weight 25KGS. 5. Storage attention: should store up in the dry well ventilated warehouse, take approves separates depositing as the unit.. Prevents the solarization and damp, should be far away from the heat source, must use to have awning's transport to prevents the rain to drench and to pollute in the transportation Packed in kraft paper and polypropylene plastic woven compound bag , each bag of net weight 25KGS.
Epoxy Resin
Our company, CNMI Industrial Corporation is one of the biggest epoxy resin and mica powder suppliers. We have been in the field of manufacturing and exporting epoxy resin and mica powder for more than 15 years. We are Alibaba Certificated factory. Product get FDA certificate (Safe for food touch). 1. Alibaba identification Manufacturer for Mica Powder. 2. Our Mica Powder produced according to the standard quality and 100% solved in resin. 3. We have been get FDA certificate for the Mica powder. 4. Lots of color for you choose. 5. Accept OEM order with your lable. Attached is our mica powder catalogue, please kindly check and tell us your detailed requirement for the mica powder, colors and quantity. We also have liquid dye, glitter, glow in the dark powder, if you have requirement, welcome inquiry. Looking forward to your early reply, and hope there's a chance for us to cooperate. m
